journal article·2017-04

Microscopic investigation of failure mechanisms in AA5182-O sheets subjected to electro-hydraulic forming

Arash Jenab, Daniel E. Green, Ahmet T. Alpas

Publisher page

Abstract

Abstract In this study, damage mechanisms in AA5182-O aluminium sheets are investigated using quasi-static (QS) Marciniak tests and high strain-rate electro-hydraulic forming (EHF) process. The results confirm that void nucleation, growth and coalescence are the main damage mechanisms of AA5182-O at both high and low strain rates. The EDS analysis suggests that cracking of Al 3 (Fe-Mn) intermetallic particles is the main source of void nucleation, whereas Mg 2 Si particles do not majorly influence void formation. Void growth analysis suggests that specimens deformed under QS conditions contained more voids in areas away from the sub-fracture surface but specimens deformed at high strain rate exhibit more significant rate of void growth close to sub-fracture areas. Void formation is suppressed by increasing the applied energy in EHF. And more significantly, the growth of voids is suppressed due to the high-velocity impact of the sheet against the die which plays an important role in increasing formability of AA5182-O aluminium sheet in EHF process. When the void percentage increase remains less than about 0.5% AA5182-O can be formed safely. However, when the void percentage increases beyond 0.6–0.8% fracture becomes inevitable.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Non-Destructive Testing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. I.J. Polmear, Light Alloys From Traditional Alloys to Nanocrystals, Butterworth-Heinemann-Elsevier, Oxford, 2006.
2. Recent development in aluminium alloys for the automotive industry10.1016/S0921-5093(99)00653-X ↗
3. Hyperplasticity increased forming limits at high workpiece velocity10.1016/0956-716X(94)90613-0 ↗
4. Hyperplasticity enhanced formability at high rates10.1016/0924-0136(94)90404-9 ↗
5. Experimental characterization of sheet metal deformation during electro-hydraulic forming10.1016/j.jmatprotec.2011.06.005 ↗
6. Electro-hydraulic forming of sheet metals free-forming vs. conical-die forming10.1016/j.jmatprotec.2011.12.014 ↗
7. An investigation of enhanced formability in AA5182-O Al during high-rate free-forming at room-temperature quantification of deformation history10.1016/j.jmatprotec.2013.07.015 ↗
8. Quantitative microstructural analysis of formability enhancement in dual phase steels subject to electrohydraulic forming10.1007/s11665-012-0438-2 ↗
9. Formability of dual phase steels in electrohydraulic forming10.1016/j.jmatprotec.2013.01.026 ↗
10. Numerical modelling of electrohydraulic free-forming and die-forming of DP590 steel10.1016/j.jmapro.2014.04.004 ↗
11. High strain rate tensile testing of automotive aluminum alloy sheet10.1016/j.ijimpeng.2005.04.013 ↗
12. Workability of 1045 spheroidized steel under superimposed hydrostatic pressure10.1007/BF02663205 ↗
13. Effects of superimposed hydrostatic pressure on fracture in sheet metals under tension10.1016/j.ijmecsci.2009.09.014 ↗
14. Effect of velocity on flow localization in tension10.1016/1359-6454(95)00228-6 ↗
15. Enhanced formability of interstitial free iron at high strain rates10.1016/0956-716X(92)90019-B ↗
16. The effect of tool-sheet interaction on damage evolution in electromagnetic forming of aluminum alloy sheet10.1115/1.1839212 ↗
17. Analysis of failure in dual phase steel sheets subject to electrohydraulic forming
18. A. Jenab, D.E. Green, A.T. Alpas, K.P. Boyle, Formability of AA5182-O Sheet during Electro-Hydraulic Forming: Influence of Input Energy. in: MS&T, 2015, pp. 535–542.
19. The use of genetic algorithm and neural network to predict rate-dependent tensile flow behaviour of AA5182-O sheets10.1016/j.matdes.2016.01.038 ↗
20. Hull · 1999
21. K.R. Spencer, Evolution of fracture in an automotive aluminum alloy under plane strain tension, (Ph.D. thesis), University of Waterloo, 2000.
22. Effects of strain rate on mechanical properties and failure mechanism of structural Al-Mg alloys10.1016/j.msea.2008.03.037 ↗
23. ASTM-E1251-11, Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry (2011). http://dx.doi.org/10.1520/E1251-11.10.1520/E1251-11 ↗
24. ASTM-E8/E8M11, Standard Test Methods for Tension Testing of Metallic Materials (2016). http://dx.doi.org/10.1520/E0008.
25. A.C. Thompson, High Strain Rate Characterization of Advanced High Strength Steels by, (Ph.D. thesis), University of Waterloo, 2006.
26. Constitutive modelling of dual phase steel sheet and tube
27. Effect of strain rate on flow stress and anisotropy of DP600, TRIP780, and AA5182-O sheet metal alloys10.1016/j.ijimpeng.2015.09.006 ↗
28. High-ve­loc­ity metal form­ing, met­al­work­ing: sheet form­ing
29. O.S. Orlov, A Three-Dimensional Damage Percolation Model, (Ph.D. thesis), Department of Mechanical and Mechatronics Engineering, University of Waterloo (2006).
30. Constituent particle break-up during hot rolling of AA518210.1002/adem.200900241 ↗
31. A eutectoid phase transformation for the primary intermetallic particle from Alm(Fe,Mn) to Al3(Fe,Mn) in AA5182 alloy10.1016/j.actamat.2004.02.041 ↗
32. Solidification structures and phase selection of iron-bearing eutectic particles in a DC-cast AA5182 alloy10.1016/j.actamat.2004.02.015 ↗
33. Micromechanisms of multistage fatigue crack growth in a high-strength aluminum alloy10.1016/j.actamat.2006.11.009 ↗
34. Damage characterization and modeling of a 7075-T651 aluminum plate10.1016/j.msea.2009.07.049 ↗
35. Damage characterization and damage percolation modelling in aluminum alloy sheet10.1016/S1359-6454(01)00163-X ↗
36. Work-hardening of copper of copper - silica -5. Equilibrium plastic relaxation by secondary dislocations10.1080/14786437608222028 ↗
37. Thomason · 1990
38. A criterion for ductile fracture by the growth of holes10.1115/1.3601204 ↗
39. Continuum model for void nucleation by inclusion debonding10.1115/1.3173064 ↗
40. An analysis of inclusion morphology effects on void nucleation10.1088/0965-0393/10/2/305 ↗
41. Investigation of void nucleation in Al-Mg sheet10.1016/j.msea.2006.12.150 ↗
42. Metallurgical investigations on hyperplasticity in dual phase steel sheets10.1115/1.4027492 ↗