journal article·2011-09

Effects of heat treatment processes on microstructure and creep properties of a high nitrogen 15Cr–15Ni austenitic heat resistant stainless steel

Vu The Ha, Woo Sang Jung

Materials Science and Engineering: A· Volume 528· Issue 24
Publisher page

Abstract

Abstract Conventional thermo-mechanical treatment (CTMT) and modified thermo-mechanical treatment (MTMT) process were applied for manufacturing a high nitrogen niobium-stabilized 15Cr–15Ni austenitic alloy. CTMT process consists of 5 h of solution treatment at 1270 °C followed by water quenching and subsequent aging at 820 °C for 50 h. MTMT process differs from CTMT process in hot plastic deformation performed immediately after the solution treatment at 1270 °C and longer aging time. Microstructure and creep properties of the steel obtained by both processing routes were investigated. Creep rupture tests at 750 °C showed double increase in rupture time brought about by MTMT process. Examination of crept microstructure by transmission electron microscopy revealed that the improved creep properties in MTMT process were mainly due to improved distribution uniformity of fine nano-sized carbonitride precipitates in the austenitic matrix and that MTMT process has no effects on the number density and distribution of copper precipitates present in the steel. However, the creep ductility in MTMT process drastically reduced comparing to CTMT process. The higher density of grain boundaries due to finer grain recrystallized microstructures and the formation of higher volume fraction of coarser M23C6 precipitates at the boundaries are believed to be the main reason for the lower creep ductility in MTMT process.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Viswanathan · J. Mater. Eng. Perf. · 2001 · 10/1 · 8110.1361/105994901770345394 ↗
2. Rautio · Adv. Mater. Proc. · 2008 · 35
3. T. Sourmail, Thesis, University of Cambridge, London, 2001, pp. 12–14.
4. Shingledecker · Int. J. Press. Vessels Piping · 2007 · 84 · 2110.1016/j.ijpvp.2006.09.014 ↗
5. Tohyama · NKK Tech. Rev. · 2001 · 84 · 30
6. Ishitsuka · JSME Int. J. Ser. A · 2002 · 45/1 · 11010.1299/jsmea.45.110 ↗
7. Liljestrand · Met. Trans. A · 1975 · 6A · 27910.1007/BF02667282 ↗
8. Kotecki · 1993
9. Caminada · Int. J. Press. Vessels Piping · 2010 · 87 · 33610.1016/j.ijpvp.2010.03.009 ↗
10. Shinya · J. Intell. Mater. Syst. Struct. · 2006 · 17 · 112710.1177/1045389X06065238 ↗
11. Masiasz · J. Turbomach. · 2006 · 128 · 81410.1115/1.2187525 ↗
12. Tendo · ISIJ Int. · 2001 · 41/3 · 26210.2355/isijinternational.41.262 ↗
13. Maruyama · Mater. Sci. Eng. · 2002 · A327 · 3410.1016/S0921-5093(01)01889-5 ↗
14. Tohyama · 1999 · 494
15. Baena · An Int. J. Curr. Microbiol. · 2006 · 53 · 49110.1007/s00284-006-0193-4 ↗
16. Zhang · J. Mater. Sci. Technol. · 2008 · 24/5 · 781
17. Yu Chentsov · Met. Sci. Heat Treatment · 1981 · 23/1 · 6910.1007/BF00700310 ↗
18. Kimura · 1986 · 221
19. Aghaie · Mater. Sci. Eng. A · 2008 · 487 · 38810.1016/j.msea.2007.11.010 ↗
20. Estrin · Acta Mater. · 1999 · 47/2 · 59510.1016/S1359-6454(98)00362-0 ↗
21. Gittins · J. Mater. Sci. · 1970 · 5 · 23310.1007/BF00550999 ↗