journal article·2019-03

Short austenitization treatment with subsequent press hardening: Correlation between process parameters, microstructure and mechanical properties

Olexandr Grydin, Anatolii Andreiev, Martin Joachim Holzweißig, Christian Johannes Rüsing, Kristina Duschik, Yaroslav Frolov, Mirko Schaper

Publisher page

Abstract

Abstract This study discusses contact heating of blanks as a time- and cost-saving alternative to conventional heating in radiation furnaces for press hardening of high-strength car body elements. Different from radiation furnaces, where the process takes up to 10 min, contact heating allows to austenitize the material within seconds. Various experimental series were carried out to investigate the influence of short austenitization on the microstructure and resulting mechanical properties after subsequent press hardening. Attention was given to the individual effects on the relevant processing parameters of the production chain “contact heating – press hardening”. Those include thickness and initial state of the material, cooling rate as well as the presence of post-treatment (cathodic dip coating). The obtained results were compared both to the conventionally austenitized and press-hardened material as well as to the requirements of the industrial standard. Finally, the feasibility of the process was proven by considering the example of press hardening of a door impact beam.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. A review on hot stamping10.1016/j.jmatprotec.2010.07.019 ↗
2. Portfolio der Warmumformstähle für differenzierte Bauteilanforderungen
3. Hot stamping
4. T. Vibrans, Induktive Erwärmung von Formplatinen für die Warmumformung. Dissertation, Chemnitz, 2016.
5. Review of the high-temperature oxidation of iron and carbon steels in air or oxygen10.1023/A:1023685905159 ↗
6. A. Zeichner, Entwicklung einer Ofenrollenbeschichtung für das Presshärten, Aachen, 2013.
7. U. Götze, S. Zönnchen, J. Schönherr, Wirtschaftliche Bewertung von Prozesskettenvarianten am Beispiel von Strukturbauteilen, in: R. Neugebauer, U. Götze, W. Drossel (Eds.), Tagungsband zum 1. und 2. Methodenworkshop der Querschnittsarbeitsgruppe 1 Energetisch-wirtschaftliche Bilanzierung des Spitzentechnologieclusters eniPROD, Wissenschaftliche Scripten, Auerbach, 2013, pp. 375–396.
8. R. Kolleck, R. Veit, Current and future trends in the field of hot stamping of car body parts, in: H. Wieland (Ed.), Proceedings of 3rd International Conference on Steels in Cars and Trucks, Stahleisen, Düsseldorf, 2011, pp. 67–74.
9. R. Kolleck, R. Veit, F. Lenze, Alternative Erwärmungstechnologien für die temperierte Blechumformung, in: M. Liewald (Ed.), Tagungsband "Neuere Erwärmungstechnologien in der Blechumformung", MAT INFO, Frankfurt am Main, 2008, pp. 226–234.
10. Entwicklung einer Anlage zur induktiven Erwärmung von Formplatinen
11. Advanced induction heating system for hot stamping10.1007/s00170-018-2385-z ↗
12. H. Livatyali, M. Terziakin, Forming of heat treatable-high strength steel sheets at elevated temperature, in: I. Hagen, H. Wieland (Eds.), Steel - Future for the Automotive Industry, Stahleisen, Düsseldorf, 2005, pp. 187–195.
13. Warm and hot stamping of ultra high tensile strength steel sheets using resistance heating10.1016/S0007-8506(07)60085-7 ↗
14. Evolution of microstructure and properties of steel 22MnB5 due to short austenitization with subsequent quenching10.1002/srin.201600086 ↗
15. V. Ploshikhin, A. Prihodovsky, J. Kaiser, R. Bisping, H. Lindner, G. Lengsdorf, K. Roll, New heating technology for furnace-free press hardening process, in: Tools and Technologies for Processing Ultra High Strength Materials, 19–21 September, 2011, pp. 1–8.
16. J.N. Rasera, K.J. Daun, M. D'Souza, Direct contact heating for hot forming die quenching, in: ASME 2014 International Mechanical Engineering Congress and Exposition, Friday 14 November, 2014, pp. 1–8.10.1115/IMECE2014-38373 ↗
17. Influence of short austenitization treatments on the mechanical properties of low-alloy steels for hot forming applications10.1007/s11661-015-2907-3 ↗
18. Conduction heating of boron alloyed steel in application for hot stamping10.1007/s12541-015-0258-z ↗
19. Investigation on induction heating for hot stamping of boron alloyed steels10.1016/j.cirp.2009.03.090 ↗
20. R. Veit, R. Kolleck, C. Gasser, G. Wilfinger, Development of a close-to-production prototype of an induction heating device for hot stamping of boron alloyed steels, in: H. Wieland (Ed.), Proceedings of 3rd International Conference on Steels in Cars and Trucks, Stahleisen, Düsseldorf, 2011, pp. 83–90.
21. Temperature distribution of boron-manganese sheet metal blank by induction heating in application for hot stamping10.15302/J-ENGI-2014026 ↗
22. T. Marten, J. Niewel, T. Tröster, Investigation on alternative heating concepts for the hot sheet metal forming, HTM, 66, 2011, pp. 309–315.10.3139/105.110119 ↗
23. T. Carsten, Warmformlinie sowie Verfahren zur Herstellung eines warmumgeformten und pressgehärteten Kraftfahrzeugbauteils, EP 2 730 665 A1, 2014.
24. M. Niesse, J. Lackmann, G. Frost, S. Konrad, H. Lambers, Warmformlinie und Verfahren zur Herstellung von warmumgeformten Blechprodukten, DE 10, 2014, 101 539 B9, Benteler Automobiltechnik GmbH, 2016.
25. Formhärten von feuerverzinktem 22MnB5: ein stabiler und reproduzierbarer Prozess
26. Mercedes-Benz, Body Components Manufactured from Press-Hardened Steel Sheets, 2008. 〈https://wenku.baidu.com/view/eedd61ed960590c69fc37644.html〉,
27. Verband der Automobilindustrie e.V., Plättchen-Biegeversuch für metallische Werkstoffe, Verband der Automobilindustrie, Berlin, 2010.
28. Improved etching technique to emphasize martensite and bainite in high-strength dual-phase steel10.1007/BF03354553 ↗
29. Crystallographic analysis of martensite in 0.2C-2.0Mn-1.5Si-0.6Cr steel by EBSD
30. Estimation of martensite feature size in a low-carbon alloy steel by microtexture analysis of boundaries10.1016/j.micron.2014.09.008 ↗
31. Deutsches Institut für Normung e.V., Stahl - Mikrophotographische Bestimmung der erkennbaren Korngröße (ISO 643:2012); Deutsche Fassung EN ISO 643:2012, Beuth, Berlin, 2013.
32. Tempering of steel10.1007/BF02642436 ↗
33. Herstellung von gewichtsoptimierten Strukturbauteilen durch den Einsatz presshärtbarer Stähle
34. Ferrite recrystallization and austenite formation in cold-rolled intercritically annealed steel10.1007/BF02658671 ↗
35. Characterization of the bendability of press-hardened 22MnB5 steel10.1002/srin.201300276 ↗
36. Automated single-particle SEM/EDX analysis of submicrometer particles down to 0.1 μm10.1021/ac0009604 ↗
37. Simulation eines partiellen Presshärteprozesses unter Berücksichtigung thermomechanischer und metallurgischer Zusammenhänge
38. Development of Niobium Alloyed Press Hardening Steel with Improved Properties for Crash Performance10.4028/www.scientific.net/AMR.1063.7 ↗
39. K. Hikida, N. Kojima, Effects of heating time on transformation during cooling of boron steel sheets, in: K. Steinhoff, M. Oldenburg, B. Prakash (Eds.), Proceedings of 5th International Conference "Hot Sheet Metal Forming of High-Performance Steel", Wissenschaftliche Scripten, Auerbach, 2015, pp. 541–548.
40. Bhadeshia · 2001
41. Effect of solution carbon and retained austenite films on the development of deformation structures of low-carbon lath martensite10.2355/isijinternational.53.2226 ↗
42. P. Kelly, J. Nutting, The martensite transformation in carbon steels, in: Royal Society (Ed.), in: Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, The Royal Society Publishing, London, 1960, pp. 45–58.
43. Effect of quenching rate on hardness and microstructure of hot-stamped steel10.1016/j.jallcom.2011.12.154 ↗
44. Setting mechanical properties of high strength steels for rapid hot forming processes10.3390/ma9040229 ↗
45. Effect of cooling rate on the high strain rate properties of boron steel10.1016/j.ijimpeng.2009.05.009 ↗
46. M. Naderi, Hot Stamping of Ultra High Strength Steels. Dissertation, Aachen, 2007.
47. A. Guk, A. Kunke, V. Kräusel, D. Landgrebe, Influence of inductive heating on microstructure and material properties in roll forming processes, in: Author(s), p. 80027.
48. J. Orlich, A. Rose, P. Wiest, Atlas zur Wärmebehandlung der Stähle, Stahleisen M.B.H., Düsseldorf, 1973.
49. Microstructure and mechanical properties of bainite containing martensite and retained austenite in low carbon HSLA steels10.2320/matertrans1989.32.715 ↗
50. Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures10.1179/174328409X433813 ↗
51. Strength of mixtures of bainite and martensite10.1179/mst.1994.10.3.209 ↗
52. The deformation and ageing of mild steel: III. Discussion of results10.1088/0370-1301/64/9/303 ↗
53. The cleavage strength of polycrystals
54. Formation of austenite during intercritical annealing of dual-phase steels10.1007/BF02643686 ↗
55. Improvement in lower temperature mechanical properties of 0.40 pct C-Ni-Cr-Mo ultrahigh strength steel with the second phase lower bainite10.1007/BF02644225 ↗
56. Werkstoffverbund TriBond® - Neue Möglichkeiten in der Warmumformung
57. The formation of austenite in a low-alloy steel10.1007/BF02700436 ↗
58. Gridnev · 1973
59. The rapid heat treatment of steel10.1007/BF02662639 ↗
60. J.J. Wilzer, Wärmeleitfähigkeit martensitisch härtbarer Stähle: Physikalische Zusammenhänge, Einflussfaktoren und technischer Nutzen, Lehrstuhl Werkstofftechnik, RUB, Bochum, 2014.
61. C. Arya, A. Ghosh, A. Moitra, A. Bhaduri, R. Mitra, D. Chakrabarti, The Role of Crystallographic Orientation of Martensitic Variants on Cleavage Crack Propagation, arXiv:1606.09474 [cond-mat.mtrl-sci], pp. 1–8.
62. The tempering of iron-carbon martensite; dilatometric and calorimetric analysis10.1007/BF02645469 ↗
63. Effect of cooling rate on morphology and crystallography of lath martensite in Fe-Ni alloys10.4028/www.scientific.net/MSF.638-642.1459 ↗
64. Deformation, fracture, and mechanical properties of low-temperature-tempered martensite in SAE 43xx steels10.1007/s11661-997-0139-x ↗
65. Relationship between microstructure, mechanical properties and damage mechanisms in high martensite fraction dual phase steels10.2355/isijinternational.ISIJINT-2015-186 ↗
66. Influence of hot plastic deformation and cooling rate on martensite and bainite start temperatures in 22MnB5 steel10.1016/j.msea.2012.01.018 ↗
67. Critical review of automotive hot-stamped sheet steel from an industrial perspective10.1080/02670836.2018.1425239 ↗
68. Effect of plastic hot deformation on the hardness and continuous cooling transformations of 22MnB5 microalloyed boron steel10.1007/s11661-009-9790-8 ↗
69. Effect of part/die boundary conditions on microstructural evolution during hot stamping 2000 MPa class boron steel10.1002/srin.201700495 ↗