Serrated yielding in an advanced stainless steel Fe-25Ni-20Cr (wt%)
Source abstract
Abstract
Abstract Understanding serrated yielding behavior resulting from dynamic strain aging (DSA) is essential for design and safety considerations. In this work, uniaxial tensile tests were carried out at temperatures ranging from 298 to 1073 K and strain rates 10−5 – 10−3 s−1 followed by microstructural examination of Fe-25Ni-20Cr (wt%) austenitic stainless steel (Alloy 709), a candidate structural material for Sodium-cooled Fast Reactors. Serrated yielding was found to occur in this alloy in two temperature regimes; low-temperature serrated flow (LT-SF) from 498 to 648 K and high-temperature serrated flow (HT-SF) from 648 to 973 K (depending on the strain rate) with activation energies of 103 ± 13 kJ/mole and 204 ± 11 kJ/mole respectively. The critical strain for the occurrence of serrations was found to increase with strain rate as an exponential function with exponent (m + β) of 0.78 ± 0.1 and 1.56 ± 0.2 for the LT-SF and HT-SF regimes respectively. Based on the activation energies and m + β values, diffusion of interstitial atoms has been suggested to be responsible for serrated flow in the LT-SF regime while Cr atom migration was inferred to be responsible for DSA in the HT-SF regime. Manifestations of DSA in the Alloy 709 were observed including peaks and/or plateaus in flow stresses along with negative strain rate sensitivity at intermediate temperatures. However, no loss in ductility was observed within DSA regime attributed to the relatively high work hardening rate and strain-hardening exponent. The samples deformed in DSA regime showed planar substructure while equiaxed subgrains formed at higher temperatures. The fraction of low angle grain boundaries after deformation exhibited a valley at intermediate temperatures believed to be another manifestation of the DSA.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Fusion materials and technologies · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Structural materials for Gen-IV nuclear reactors: challenges and opportunities10.1016/j.jnucmat.2008.08.044 ↗
2. Hoffelner · 2013
3. Economic benefits of advanced materials in nuclear power systems10.1016/j.jnucmat.2009.03.018 ↗
4. W. Corwin, Advanced Structural Materials (RC-3), Nuclear Energy University Programs (NEUP), Fiscal Year (FY) 2015 Annual Planning Webinar, DOE, 2014.
5. Sham · 2015 · 1
6. High temperature time-dependent low cycle fatigue behaviour of a type 316L(N) stainless steel10.1016/S0142-1123(98)00052-8 ↗
7. Effect of temperature and strain rate on upper shelf fracture behavior of A533B Class 1 pressure vessel steel
8. Deformation mechanisms in commercial Ti (0.5 at. pct oineq) at intermediate and high temperatures (0.3 - 0.6 tinm)10.1007/BF02644581 ↗
9. Elongation minimum and strain Ram sensitivity minimum of Zircaloy-410.1016/0022-3115(83)90117-4 ↗
10. Ductility and dynamic strain aging in rapidly solidified aluminum alloys10.1007/BF02661095 ↗
11. Effect of serrated flow on deformation behaviour of AISI 403stainless steel10.1016/S0921-5093(00)00992-8 ↗
12. Influence of strain rate and temperature on tensile deformation and fracture behavior of type 316L(N) austenitic stainless steel10.1007/s11661-013-1978-2 ↗
13. Dynamic strain-aging and neutron irradiation in mild steel
14. Investigation of Portevin−Le Chatelier effect in HT-9 steel10.1016/j.msea.2015.02.022 ↗
15. Yield-point phenomena in substitutional alloys10.1179/imr.1970.15.1.101 ↗
16. Serrated plastic flow10.1007/BF02743993 ↗
17. Serrated plastic flow in austenitic stainless steel
18. Effects of carbon and nitrogen levels on the temperture ranges for serrated flow in austenitic stainless steel
19. Athermal and temperature dependent behavior of serrated flow in an austenitic stainless steel10.1016/0036-9748(85)90149-8 ↗
20. Serrated Yielding in AISI 316 Stainless Steel10.1016/0001-6160(88)90331-8 ↗
21. Dynamic strain ageing in prior cold worked 15Cr–15Ni titanium modified stainless steel (Alloy D9)10.1016/j.jnucmat.2006.03.016 ↗
22. Serrated flow behavior in AL6XN austenitic stainless steel10.1016/j.jnucmat.2009.08.002 ↗
23. LXXXVI. A note on the Portevin-Le Chatelier effect, Lond. Edinb10.1080/14786440808520347 ↗
24. A model for the portevin-Le Chatelier effect in substitutional alloys10.1016/0001-6160(72)90028-4 ↗
25. Theory of the effect of dynamic strain aging on mechanical properties10.1002/pssa.2210300120 ↗
26. On the mechanism of serrated yielding and dynamic strain ageing10.1016/0001-6160(80)90114-5 ↗
27. Dynamic strain ageing and the mechanical response of alloys
28. Effect of vacancy sinks and sources on serrated yielding due to solute locking10.1016/0036-9748(71)90179-7 ↗
29. Activation energy for serrated flow In A 15Cr-15Ni Ti-modified austenitic stainless steel10.1016/0956-7151(92)90406-5 ↗
30. Activation energy for serrated flow in type 316L(N) austenitic stainless steel10.1016/j.msea.2014.02.083 ↗
31. Stress varied creep of 20%Cr-25%Ni-Nb stabilized austenitc stainless steel, Creep strength in steel and high temperature alloys
32. Precipitation in creep resistant austenitic stainless steels10.1179/026708301101508972 ↗
33. Creep behavior and Microstructural evolution of a Fe-20Cr-25Ni (mass percent) austenitic stainless steel (alloy 709) at Elevated temperatures10.1007/s11661-018-5044-y ↗
34. A study of strain-ageing in austenite10.1016/0001-6160(66)90172-6 ↗
35. Volume and grain-boundary diffusion in 20 Cr/25/Ni_Nb stainless steel10.1179/msc.1969.3.1.93 ↗
36. In-situ nuclear magnetic resonance investigation of strain, temperature, and strain-rate variations of deformation-induced vacancy concentration in aluminum10.1007/s11661-998-0168-0 ↗
37. A proposed model for the disappearance of serrated flow in two Fe alloys10.1016/0001-6160(84)90054-3 ↗
38. The influence of grain size on elevated temperature deformation behaviour of a Type 316 stainless steel
39. On the origin of the tensile flow stress in the stainless steel AISI 316L at 300 K: back stress and effective stress10.1016/S1359-6454(99)00222-0 ↗
40. Microstructural manifestation of dynamic strain aging in AISI 316 stainless steel10.1016/j.jnucmat.2009.10.047 ↗
41. Influence of thermo-mechanical treatment on the tensile properties of a modified 14Cr–15Ni stainless steel10.1016/j.jnucmat.2014.06.067 ↗
42. Dynamic strain aging and ductility minima in zirconium10.1007/BF02643421 ↗
43. High work-hardening rate and deformation twinning of Co-Ni-based superalloy at elevated temperatures10.1080/01418619908210378 ↗
44. Correlation between strain rate sensitivity and characteristics of Portevin-LeChátelier bands in a twinning-induced plasticity steel10.1016/j.msea.2017.04.078 ↗
45. Enhanced ductility in dynamic strain aging regime in a Fe-25Ni-20Cr austenitic stainless steel10.1016/j.msea.2018.05.060 ↗
46. Murty · 2013
47. Strain rate sensitivity as a measure of ductility