journal article·2010-10Open access

Investigation of size effects of very thin aluminum and copper sheets using aero-bulge test

J. Kim, R. Golle, H. Hoffmann

Materials Science and Engineering: A· Volume 527· Issue 27-28

Abstract

Material behavior is heavily influenced by its microstructure. For very thin sheets, the ratio of the sheet thickness to the average grain size is usually small. In this case, the influence of surface grains on the material strength, which is normally lower strength than inner grains, is relatively large, so that the material strength further decreases by increasing grain size. In this paper, the change of the material behavior for very thin aluminum (99.5%) with thicknesses of 50 and 95 μm and copper (99.9%) sheet with thicknesses of 35 and 50 μm depending on the grain size were discussed. To this end, the material strength and the work hardening exponent were determined using a modified bulge test (aero-bulge test). For both materials, material strength decreases with increasing grain size and decreasing sheet thickness. For copper sheets, an additional size effect due to the amount of phosphorous was observed. The work hardening exponent of aluminum sheets changes similarly with the change of material strength. For copper sheets, the work hardening exponent was changed however anomalously vis. the work hardening exponent changes inversely with respect to the material strength.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Geiger · CIRP Ann. · 1996 · 45 · 27710.1016/S0007-8506(07)63063-7 ↗
2. Engel · J. Mater. Process. Technol. · 2002 · 125–126 · 3510.1016/S0924-0136(02)00415-6 ↗
3. Koç · J. Power Sources · 2007 · 172 · 72510.1016/j.jpowsour.2007.05.089 ↗
4. Vollertsen · J. Mater. Process. Technol. · 2004 · 151 · 7010.1016/j.jmatprotec.2004.04.266 ↗
5. Vollertsen · CIRP Ann. · 2006 · 55 · 29110.1016/S0007-8506(07)60419-3 ↗
6. Hall · Phys. Soc.: Proc. · 1951 · 64 · 74710.1088/0370-1301/64/9/303 ↗
7. Petch · Iron Steel Inst. · 1953 · 174 · 25
8. Kals · SheMet · 1996 · 2 · 65
9. Michel · J. Mater. Process. Technol. · 2003 · 141 · 43910.1016/S0924-0136(03)00570-3 ↗
10. Kim · J. Manuf. Sci. Eng. · 2007 · 129 · 47010.1115/1.2714582 ↗
11. Kals · J. Mater. Process. Technol. · 2000 · 103 · 9510.1016/S0924-0136(00)00391-5 ↗
12. Hansen · Acta Mater. · 1977 · 25 · 86310.1016/0001-6160(77)90171-7 ↗
13. Raulea · J. Mater. Process. Technol. · 2001 · 115 · 4410.1016/S0924-0136(01)00770-1 ↗
14. Mahabunphachai · Int. J. Mach. Tools Manuf. · 2008 · 48 · 101410.1016/j.ijmachtools.2008.01.006 ↗
15. Atkinson · Int. J. Mech. Sci. · 1997 · 39 · 76110.1016/S0020-7403(96)00093-8 ↗
16. Hill · Philos. Mag. · 1950 · 4–41 · 1113
17. Chakrabarty · J. Strain Anal. · 1970 · 5 · 15510.1243/03093247V053155 ↗
18. Kruglov · Mater. Sci. Eng. · 2002 · A323 · 41610.1016/S0921-5093(01)01376-4 ↗
19. Ashby · Philos. Mag. · 1970 · 21 · 39910.1080/14786437008238426 ↗
20. Taylor · Proc. R. Soc. (Lond.) · 1943 · A145 · 362
21. Yuichiro · J. Inst. Met. · 2001 · 65 · 21710.2320/jinstmet1952.65.3_217 ↗
22. Jia · Scripta Mater. · 2006 · 54 · 124710.1016/j.scriptamat.2005.12.035 ↗