Creep rupture behavior of Hastelloy C276-BNi2 brazed joint
Source abstract
Abstract
Abstract This paper studied the creep rupture behavior of Hastelloy C276-BNi2 brazed joint by experimental. Based on a series of creep rupture tests at 600 °C under 110–250 MPa, a relation between the stress and rupture time was achieved to evaluate the creep life of brazed joint. The results show that all the brazed joints were fractured in brazed seam immediately after the second creep stage. The creep model, fracture behavior and failure mechanism are dependent on the level of applied stress. The creep behavior of the brazed joint should be depicted by two-regime Norton (2RN) creep model rather than single Norton model. The creep damage tolerance factor was used to identify the cause of creep damage. From low to high stress level, the failure mode is changed from intergranular brittle to transgranular ductile fracture due to the increases of damage tolerance factor with applied stress increases.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. High temperature strength and inelastic behavior of plate-fin structures for HTGR10.1016/j.nucengdes.2006.09.007 ↗
2. Development of structural design procedure of plate-fin heat exchanger for HTGR10.1016/j.nucengdes.2012.09.013 ↗
3. Optimal design approach for the plate-fin heat exchangers using neural networks cooperated with genetic algorithms10.1016/j.applthermaleng.2007.03.032 ↗
4. High temperature strength and inelastic behavior of plate-fin structures for HTGR10.1016/j.nucengdes.2006.09.007 ↗
5. Creep of brazed plate-fin structures in high temperature compact heat exchangers10.1007/s11465-009-0065-2 ↗
6. Elevated temperature creep and fracture properties of the 62Cu-35Au-3Ni braze alloy10.1007/BF02647598 ↗
7. Creep rupture and fatigue properties of transient liquid phase bonded joints of Ni base single crystal superalloy10.1179/026708303225001957 ↗
8. Creep and fatigue lifetime analysis of directionally solidified superalloy and its brazed joints based on continuum damage mechanics at elevated temperature10.1016/j.matdes.2012.09.052 ↗
9. Effect of diffusion treatment on microstructures and mechanical properties of wide-gap brazed joints of cast superalloy K403
10. Effect of heat treatment on γ’ phase and property of brazed joints of K403 alloy
11. Parametric study of the creep failure of double lap adhesively bonded joints10.1016/j.matdes.2014.08.003 ↗
12. Impression creep behavior of Sn-3.5Ag-0.7Cu/Cu brazed10.1016/j.proeng.2015.12.279 ↗
13. A comparison of brazed residual stress in plate-fin structure made of different stainless steel10.1016/j.matdes.2008.04.051 ↗
14. The effect of filler metal thickness on residual stress and creep for stainless steel plate-fin structure10.1016/j.ijpvp.2008.02.007 ↗
15. Creep damage and crack initiation in P92-BNi2 brazed joint10.1016/j.matdes.2015.01.011 ↗
16. The microstructure, mechanical properties and fracture behavior of hastelloy C276-BNi2 brazed joint10.1016/j.matdes.2016.11.069 ↗
17. Notch effect on creep damage for Hastelloy C276-BNi2 brazing joint10.1016/j.matdes.2015.06.111 ↗
18. Creep failure prediction of brazing joints with double notches10.1016/j.matdes.2016.03.140 ↗
19. Effect of notch position on creep damage for brazed joint10.1016/j.advengsoft.2016.07.001 ↗
20. Experimental investigations on creep rupture strength and failure mechanism of vacuum brazed joints of a DS superalloy at elevated temperature10.1016/j.msea.2012.02.099 ↗
21. Prediction of creep crack growth behaviour in 316H stainless steel for a range of specimen geometries10.1016/j.ijpvp.2014.05.006 ↗
22. Damage localization of conventional creep damage models and proposition of a new model for creep damage analysis10.1299/jsmea.41.57 ↗
23. An empirical relationship between for rupture life and minimum creep rate in creep rupture tests
24. Evans · 1984 · 18
25. The relation between minimum creep rate and time to fracture10.1080/03063453.1976.11683560 ↗
26. Relationship for rupture and creep stresses
27. Determination and application of larson-miller parameter for heat resistant steel 12CrlMoV and 15CrMo
28. Tension and creep design stresses of the “Hastelloy-X” alloy for high-temperature gas cooled reactors10.1016/j.msea.2006.12.184 ↗
29. Creep damage mechanics and micromechanisms10.1016/B978-1-4832-8440-8.50017-X ↗
30. Creep deformation behavior of modified 9Cr- 1Mo steel10.1016/j.jnucmat.2011.02.024 ↗
31. Tertiary creep in nickel-base superalloys: analysis of experimental data and theoretical synthesis10.1016/0001-6160(87)90083-6 ↗
32. Intergranular fracture during power-law creep under multiaxial stresses10.1179/030634580790441187 ↗
33. Creep deformation in a modified 9Cr-1Mo steel10.1179/026708303225009436 ↗
34. The creep behavior of discontinuously reinforced metal-matrix composites10.1007/s11837-003-0187-7 ↗
35. Creep rupture behavior of 9Cr-1.8W-0.5Mo-VNb (ASME grade 92) ferritic steel weld joint10.1016/j.msea.2013.10.071 ↗
36. A multiaxial creep-damage model for creep crack growth considering cavity growth and microcrack interaction10.1016/j.engfracmech.2014.03.001 ↗
37. The growth of grain boundary voids under stress10.1080/14786435908243264 ↗
38. An analysis of the effect of cavity nucleation rate and cavity coalescence on the tensile behavior of superplastic materials10.1007/s11661-000-0260-6 ↗
39. Creep cavitation in metals10.1016/S0749-6419(02)00111-0 ↗
40. The role of cavity growth mechanisms in determining creep-rupture under multiaxial stresses10.1111/j.1460-2695.1994.tb00257.x ↗
41. A review on damage mechanisms, models and calibration methods under various deformation conditions10.1177/1056789505050357 ↗
42. Vacancy potential and void growth on grain boundaries10.1179/030634575790445161 ↗
43. Constraints on the diffusive cavitation of isolated grain boundary facets in creeping polycrystals10.1016/0001-6160(81)90150-4 ↗
44. Continuous cavity nucleation and creep fracture10.1016/0036-9748(83)90065-0 ↗
45. Creep and fracture of metals: mechanisms and mechanics10.1051/rphysap:01988002304060500 ↗