Determination of the single-phase constitutive relations of α/β dual phase TC6 titanium alloy
Source abstract
Abstract
Abstract The constitutive relations of α and β phases in a TC6 titanium alloy were determined by implementing a two-phase elastic-plastic self-consistent (EPSC) framework combined with the evolution of lattice strains; these strains were obtained via in-situ tensile loading synchrotron-based x-ray diffraction experiments. It was found that the {200}β reflection has the lowest stiffness and load partitions prior to the α phase during the elastic loading stage in this alloy. The simulated parameters including the diffraction elastic constant and initial yield stress of lattice reflections exhibited satisfactory correspondence with the experimental results. Further analysis of the characteristics of the Schmid Factor (SF) distributions of the main slip systems revealed that the elastic-plastic transition process in the α phase occurs over a prolonged period. In contrast, the β phase undergoes a transient process owing to its relatively more concentrated SF frequency distributions, than those of the α phase. In addition, the fitted stress-strain curve of each phase was compared with the measured macro stress-strain curve obtained from the in-situ experiment. It revealed Young's moduli of 110.3 GPa and 104.5 GPa, and yield stresses of 877.8 MPa and 969 MPa, for the α and β phases, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Microstructure and mechanical properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Micromechanical Modeling of Ferrite-Pearlite Steels Using Finite Element Unit10.2355/isijinternational.40.1170 ↗
2. Predicting the deformation behavior of ferrite-pearlite steels using micro mechanical modeling of cells10.1016/j.mechmat.2013.04.005 ↗
3. based machining simulation methodology accounting for cast iron microstructure10.1016/j.finel.2013.10.006 ↗
4. Characterization and modelling of failure initiation in DP steel10.1016/j.commatsci.2013.04.001 ↗
5. Micromechanics stress-strain behavior prediction of dual phase steel considering plasticity and grain boundaries debonding10.1016/j.matdes.2014.12.013 ↗
6. Deformation response of ferrite and martensite in a dual-phase steel10.1016/j.actamat.2013.10.001 ↗
7. Separation of size-dependent strengthening contributions in fine-grained Dual Phase steels by nanoindentation10.1016/j.actamat.2006.03.031 ↗
8. Micropillar and macropillar compression responses of magnesium single crystals oriented for single slip or extension twinning10.1016/j.actamat.2013.10.073 ↗
9. Lattice strain evolution during uniaxial tensile loading of stainless steel10.1016/S0921-5093(98)00878-8 ↗
10. Elastoplastic deformation of ferritic steel and cementite studied by neutron diffraction and self-consistent modelling10.1016/S1359-6454(02)00026-5 ↗
11. Lattice strain evolution in IMI 834 under applied stress10.1016/S0921-5093(02)00183-1 ↗
12. Interphase and intergranular stress generation in composites exhibiting plasticity in both phases10.1016/j.actamat.2005.02.041 ↗
13. Effect of cyclic plasticity on internal stresses in a metal matrix composite10.1007/s11661-006-0140-9 ↗
14. Self-consistent modelling of lattice strains during the in-situ tensile loading of twinning induced plasticity steel10.1016/j.msea.2013.09.073 ↗
15. Intergranular strain and texture in steel Luders bands10.1016/j.actamat.2005.04.008 ↗
16. Investigation of deformation mechanisms involved in the plasticity of AZ31 Mg alloy: In situ neutron diffraction and EPSC modelling10.1016/j.msea.2008.07.031 ↗
17. Measured and predicted intergranular strains in textured austenitic steel10.1016/S1359-6454(99)00354-7 ↗
18. Two-dimensional detector software: from real detector to idealised image or two-theta scan10.1080/08957959608201408 ↗
19. An investigation into the warm deformation behavior of Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si alloy10.1016/j.msea.2015.12.065 ↗
20. Stepped superplasticity deformation-induced plastic enhancement of Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si alloy10.1016/j.matdes.2011.09.048 ↗
21. Continuum micro-mechanics of elastoplastic polycrystals10.1016/0022-5096(65)90023-2 ↗
22. Elastic-Plastic Behaviour of Polycrystalline Metals and Composites
23. A study of residual stresses in Zircaloy-2 with rod texture10.1016/0956-7151(94)90191-0 ↗
24. The Elastic Field Outside an Ellipsoidal Inclusion
25. Kocks · 1998
26. Evolution of lattice strain in Ti-6Al-4V during tensile loading at room temperature10.1016/j.actamat.2008.08.030 ↗
27. Microstructure of polycrystalline Ti and its microelectrochemical properties by means of electron-backscattering diffraction (EBSD)10.1016/S0013-4686(01)00572-2 ↗
28. O. Engler, V. Randle. Introduction to Texture Analysis: Macrotexture, Micro-Texture, Orientation Mapping, 2000.
29. Kocks · 1998
30. Microtexture determination by electron back-scatter diffraction10.1007/BF01165988 ↗
31. Brandes · 1992
32. Phonon dispersion of the bcc phase of group-IV metals. I. bcc titanium10.1103/PhysRevB.43.10933 ↗
33. Twinning and texture development in two Mg alloys subjected to loading along three different strain paths10.1016/j.actamat.2007.03.006 ↗
34. Use of Schmid factors to select extension twin variants in extruded magnesium alloy tubes10.1016/j.scriptamat.2006.07.059 ↗
35. Simulation of slip band evolution in duplex Ti-6Al-4V10.1016/j.actamat.2009.10.025 ↗
36. Crystal plasticity modeling of slip activity in Ti-6Al-4V under high cycle fatigue loading10.1016/j.ijplas.2008.08.004 ↗
37. Deformation behavior of HCP Ti-Al alloy single crystals10.1007/s11661-002-0153-y ↗
38. Micromechanical behavior and texture evolution of duplex stainless steel studied by neutron diffraction and self-consistent modeling10.1016/j.actamat.2007.10.040 ↗
39. An in situ high-energy X-ray diffraction study of micromechanical behavior of multiple phases in advanced high-strength steels10.1016/j.actamat.2009.05.002 ↗