Effect of yttria inclusion on room temperature tensile properties of investment cast TiAl
Source abstract
Abstract
Abstract Yttria is the best face coat material in the shell mold for the investment casting of γ-TiAl alloys. However, yttria inclusions may occur in the cast products and there is a lack of knowledge about the influence of yttria inclusions on the mechanical properties of TiAl. In the present study, the effect of yttria inclusions on room temperature tensile properties of two investment cast TiAl alloys, Ti-45Al-2Mn-2Nb (at%) + 0.08 vol% TiB2 and Ti-46 Al-2 Nb-2Cr-0.15B (at%), were studied. The results show that tensile failure tends to initiate from yttria inclusions, resulting in reduced plastic strain and ultimate strength. Yttria inclusions differ in location (surface /internal), size, and morphology (agglomerate /whole piece), those with larger sizes or located at the sample surface being more harmful. The tensile properties of inclusion containing TiAl parts can be estimated using the size and location determined by X-ray inspection. The critical size at which inclusions become detrimental to the mechanical properties of TiAl was discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Intermetallic alloys based on gamma titanium aluminide10.1007/BF03220267 ↗
2. Gamma titanium aluminides as prospective structural materials10.1016/S0966-9795(00)00073-X ↗
3. Application of TiAl in a turbocharger for passenger vehicles10.1002/1527-2648(200105)3:5<307::AID-ADEM307>3.0.CO;2-3 ↗
4. Performance, tolerance and cost of TiAl passenger car valves10.1016/j.intermet.2005.08.009 ↗
5. Appel · 2011
6. Alpha-case formation mechanism on titanium investment castings10.1016/j.msea.2005.05.092 ↗
7. Investment casting technology for production of TiAl low pressure turbine blades – process engineering and parameter analysis10.1016/j.intermet.2010.11.014 ↗
8. Investigation into refractories as crucible and mould materials for melting and casting γ-TiAl alloys10.1179/026708300101508964 ↗
9. A study of two refractories as mould materials for investment casting TiAl based alloys10.1007/s10853-006-6785-3 ↗
10. Alloy development and shell mould casting of gamma TiAl10.1016/S0924-0136(02)00873-7 ↗
11. On the evaluation of stability of rare earth oxides as face coats for investment casting of titanium10.1007/BF02667869 ↗
12. Microstructure and composition of cast Ti–47Al–2Cr–2Nb alloys produced by yttria crucibles10.1016/j.msea.2012.01.099 ↗
13. Fabrication of transparent lanthanum-doped yttria ceramics by combination of two-step sintering and vacuum sintering10.1111/j.1551-2916.2009.03312.x ↗
14. Interactions between TiAl alloys and yttria refractory material in casting process10.1016/j.jmatprotec.2010.03.003 ↗
15. Effects of inclusions on very high cycle fatigue properties of high strength steels10.1179/1743280411Y.0000000008 ↗
16. Fatigue behavior of A356-T6 aluminum cast alloys. Part I. Effect of casting defects10.1016/S1471-5317(00)00008-0 ↗
17. Intermetallics: why is it so difficult to introduce them in gas turbine engines?10.1016/j.intermet.2006.01.064 ↗
18. Chapter 7 – bearing steels
19. Effect of boron addition on tensile ductility in lamellar TiAl alloys10.1016/S0966-9795(02)00087-0 ↗
20. The role of microtexture on the faceted fracture morphology in Ti–6Al–4V subjected to high-cycle fatigue10.1016/j.actamat.2010.03.036 ↗
21. The significance of acoustic emission during stressing of TiAl-based alloys. Part I: detection of cracking during loading up in tension10.1016/S1359-6454(01)00091-X ↗
22. Chapter 2 – stress concentration
23. Surface defect tolerance of a cast TiAl alloy in fatigue10.1016/S1359-6462(01)01097-1 ↗