journal article·2007-06

In situ manipulation of cooling rates during planar-flow melt spinning processing

Cormac J. Byrne, Aaron M. Kueck, Shefford P. Baker, Paul H. Steen

Materials Science and Engineering: A· Volume 459· Issue 1-2
Publisher page

Abstract

Abstract Planar-flow melt spinning (PFMS) is a single stage rapid manufacturing/solidification technique for producing thin metallic sheet or foil. A new technology, envisioned to allow real-time manipulation of the local cooling rates and properties in melt-spun ribbon, has been tested successfully when casting Al–7%Si. Pulsed laser heating, directed low on the upstream meniscus, or on the substrate, leaves patterns of ‘dimples’ in the ribbon. Typical cooling rates of 10 4 K/s have been measured using a control-volume approach. Secondary dendrite arm spacing (SDAS) has been measured through the thickness of ribbons showing areas both affected by the laser heating and unaffected by the laser. Through a correlation of cooling rates and SDAS, it is shown that the unmodified ribbon has an average cooling rate similar to that measured macroscopically. The cooling rate underneath a laser dimple is estimated to be six times slower near the contact surface. It is envisioned that the technology described may bring the concept of ‘casting-by-design’ one step closer to realization.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Solidification and crystal growth phenomena · Fluid Dynamics and Thin Films · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. U.S. Census Bureau, Manufacturing Energy Consumption Survey, 1997.
2. D.O.E Energy Use: Aluminum Industry Brief, 1997.
3. P.H. Steen, A. Hirsa, Proceedings of the NSF Design and Manufacturing Conference, San Juan, PR, 2002.
4. M.C. Narasimhan, U.S. Patent 4,142,571 (1979).
5. Kavesh · 1978 · 36
6. Steen · Ann. Rev. Fluid Mech. · 1997 · 29 · 37310.1146/annurev.fluid.29.1.373 ↗
7. Lee · Scr. Mater. · 1997 · 37 · 16510.1016/S1359-6462(97)00086-9 ↗
8. P.H. Steen, U.S. Patent 7,082,986 (2006).
9. Young · Met. Trans. A · 1975 · 6A · 19710.1007/BF02673688 ↗
10. Spear · American Foundrymen’s Soc. Trans. · 1963 · 71 · 209
11. Matyja · J. Inst. Metals · 1968 · 96 · 30
12. Pond · Trans. Metall. Soc. AIME · 1969 · 245 · 2475
13. Flemings · 1974
14. 1989
15. Kirkwood · Mater. Sci. Eng. · 1985 · 73 · 110.1016/0025-5416(85)90294-0 ↗
16. Spinelli · J. Alloys Compd. · 2005 · 403 · 22810.1016/j.jallcom.2005.06.010 ↗
17. Bamberger · Mater. Sci. Tech. · 1987 · 3 · 4910.1179/mst.1987.3.1.49 ↗
18. Sarreal · Met. Trans. A · 1986 · 17A · 206310.1007/BF02645003 ↗
19. J. Kukura, K. Ford, A. Singh, P.H. Steen, T. Ibaraki, in: S.F., Shen, P., Dawson (Eds.), Simulations of Materials Processing: Theory, Methods, and Applications, Balkema, Rotterdam, 1995, pp. 1153–1157.
20. Byrne · Met. Mater. Trans. B · 2006 · 37B · 44510.1007/s11663-006-0029-4 ↗
21. Roosz · Prakt. Metallogr. · 2002 · 39 · 10010.1515/pm-2002-390206 ↗
22. Huang · Met. Trans. A · 1985 · 16 · 177310.1007/BF02670365 ↗
23. Ibaraki · 1996 · 159
24. T. Ibaraki, Master’s thesis, Cornell Univeristy, 1996.
25. Ma · Acta. Metall. Mater. · 1992 · 40 · 25110.1016/0956-7151(92)90300-4 ↗
26. Birol · J. Mater. Sci. · 1996 · 31 · 213910.1007/BF00356637 ↗