Experimental quantification of carbon gradients in martensite and its multi-scale effects in a DP steel
Source abstract
Abstract
Abstract In multi-phase steel grades such as ferrite-martensite dual phase (DP) steels, it is of the utmost importance to understand the underlying effects of solid phase transformations with respect to their consequences on the final mechanical properties. In the present research, by employing dilatometry experiments two equivalent DP microstructures have been designed which are identical in most primary aspects such as constituents’ volume fractions, the corresponding grain sizes and their morphologies. The difference, however, is the fashion in which carbon atoms in the martensite constituents are distributed. Electron probe microanalysis (EPMA) shows that excess carbon atoms which are rejected as a consequence of ferrite formation are accumulated in the adjacent austenite grains close to the boundaries yielding sharp carbon gradients. During final quenching, the characteristics of martensite transformation are therefore severely influenced. Through electron backscatter diffraction (EBSD) analysis many coarse substructures were detected in the interior regions of the inhomogeneous martensite associated with low dislocation densities. However, the areas close to the ferrite/martensite boundaries demonstrate finer substructures. Moreover, by means of nanoindentation tests it was found that the interior areas with lower carbon contents and coarser substructures show lower local strength as compared to the marginal regions. Macroscopic stress-strain behavior revealed that a higher ultimate tensile strength and enhanced post-uniform elongation are achieved in the specimen with sharp carbon gradients in its martensite constituents.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. N. Fonstein, Dual-phase steels, in: Automotive Steels, Elsevier, 2017, pp. 169–216.10.1016/B978-0-08-100638-2.00007-9 ↗
2. Alloying effects on microstructure formation of dual phase steels10.1016/j.actamat.2015.05.005 ↗
3. Dual phase steels10.1146/annurev.ms.11.080181.001333 ↗
4. Influence of martensite composition and content on the properties of dual phase steels10.1007/BF02659924 ↗
5. Work hardening of dual-phase steels10.1179/030634581790426615 ↗
6. Integrated experimental–simulation analysis of stress and strain partitioning in multiphase alloys10.1016/j.actamat.2014.07.071 ↗
7. Development of high throughput assays for establishing process-structure-property linkages in multiphase polycrystalline metals10.1016/j.actamat.2016.10.033 ↗
8. Influence of thermomechanical treatment on the structure-property relationship of a microalloyed dual-phase high strength, low alloy steel10.1016/0025-5416(86)90088-1 ↗
9. Microstructure control during fabrication of ultrafine grained dual-phase steel10.2355/isijinternational.52.874 ↗
10. The effect of cooling rate on the damage micromechanisms of DP steels10.4028/www.scientific.net/MSF.638-642.3337 ↗
11. Quantification of the effect of transformation-induced geometrically necessary dislocations on the flow-curve modelling of dual-phase steels10.1016/j.ijplas.2012.11.003 ↗
12. Effect of martensite strength on the tensile strength of dual phase steels10.1007/BF02385411 ↗
13. Effect of morphology of second-phase martensite on tensile properties of Fe-0.1C dual phase steels10.1007/BF00580148 ↗
14. Effect of martensite plasticity on the deformation behavior of a low-carbon dual-phase steel10.1007/s11661-006-9023-3 ↗
15. Influence of ferrite-martensite microstructural morphology on tensile properties of dual-phase steel10.1007/BF00356631 ↗
16. The dependence of some tensile and fatigue properties of a dual-phase steel on its microstructure10.1007/BF02658673 ↗
17. Influence of martensite content and morphology on the toughness and fatigue behavior of high-martensite dual-phase steels10.1007/s11661-001-0196-5 ↗
18. Bhadeshia · 2006
19. Digital image correlation studies for microscopic strain distribution and damage in dual phase steels10.1016/j.scriptamat.2007.01.031 ↗
20. Local plastic strain evolution in a high strength dual-phase steel10.1016/j.msea.2010.04.052 ↗
21. Experimental study of the distribution of alloying elements after the formation of epitaxial ferrite upon cooling in a low-carbon steel10.1016/j.matchar.2010.06.006 ↗
22. Microstructural evolution of a low-carbon steel during application of quenching and partitioning heat treatments after partial austenitization10.1007/s11661-008-9701-4 ↗
23. Martensite in steel10.1016/S0921-5093(99)00288-9 ↗
24. The effect of prior ferrite formation on bainite and martensite transformation kinetics in advanced high-strength steels10.1016/j.actamat.2013.06.043 ↗
25. Effect of prior austenite carbon partitioning on martensite hardening variation in a low alloy ferrite–martensite dual phase steel10.1016/j.msea.2014.09.041 ↗
26. Correlations between nanoindentation hardness and macroscopic mechanical properties in DP980 steels10.1016/j.msea.2013.12.084 ↗
27. Experimental and numerical study on geometrically necessary dislocations and non-homogeneous mechanical properties of the ferrite phase in dual phase steels10.1016/j.actamat.2011.03.062 ↗
28. Ferrite hardening response in a low alloy ferrite–martensite dual phase steel10.1016/j.jallcom.2013.11.183 ↗
29. Deformation response of ferrite and martensite in a dual-phase steel10.1016/j.actamat.2013.10.001 ↗
30. Characterization of dual-phase steel microstructure by combined submicrometer EBSD and EPMA carbon measurements
31. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
32. Prediction of post-dynamic austenite-to-ferrite transformation and reverse transformation in a low-carbon steel by cellular automaton modeling10.1016/j.actamat.2012.06.007 ↗
33. Quantitative analysis of the dilatation during an isothermal decomposition of austenites10.1016/S0921-5093(01)01723-3 ↗
34. Conversional model of transformation strain to phase fraction in low alloy steels10.1016/j.actamat.2006.09.008 ↗
35. Dilatometric analysis of austenite decomposition considering the effect of non-isotropic volume change10.1016/j.actamat.2006.12.007 ↗
36. In situ study of austenite formation by dilatometry in a low carbon microalloyed steel10.1016/j.scriptamat.2008.01.019 ↗
37. Modulated formation of lath martensite10.1016/j.actamat.2016.02.047 ↗
38. Effects of auto-tempering on microstructure and mechanical properties in hot rolled plain C-Mn dual phase steels10.1016/j.msea.2016.04.038 ↗
39. Structure-property changes during hardening and tempering of new ultra high strength medium carbon low alloy steel10.1179/030192303225004097 ↗
40. The influence of microstructure and composition on the plastic behaviour of dual-phase steels10.1016/j.actamat.2014.04.015 ↗
41. Failure mechanisms in DP600 steel10.1016/j.msea.2013.09.048 ↗