The influence of microstructure on the cyclic deformation and damage of copper and an oxide dispersion strengthened steel studied via in-situ micro-beam bending
Source abstract
Abstract
Abstract Service materials are often designed for strength, ductility, or toughness, but neglect the effects of cyclic time-variable loads ultimately leading to macroscopic mechanical failure. Fatigue originates as local plasticity that can first only be observed on the micro scale at defects serving as stress concentrators such as inclusions or grain boundaries. Thus, a recently developed technique to perform in-situ observation of micro scale bending fatigue experiments was applied. Micro-beams fabricated from copper, single grained and ultrafine grained (ufg), and an oxide dispersion strengthened (ODS) steel were subject to cyclic deformation and subsequent damage. The elastic stiffness, yield strength, dissipated energy, and maximum stress were measured as a function of cycle number and plastic strain amplitude. From these properties, cyclic stress-strain curves were developed. Initial pronounced monotonic hardening and an increasing Bauschinger effect were observed in all samples with increasing strain amplitude. Cyclic stability was maintained until plastic strain amplitudes reached a critical value. At this point, dramatic cyclic softening and microcracking occurred. The critical strain amplitude was found to be approximately 5.4×10 −3 for the copper with a refined grain structure and 1.2×10 −2 for the steel specimen. Grain rotation and noticeable changes in sub-grain structure were evident in the ufg copper after a critical strain amplitude of e a =8.3×10 −3 . In-situ micro fatigue bending couples the cyclic evolution of bulk mechanical properties measurements with real-time electron microscopy analysis techniques of damage and failure mechanisms, which renders it a powerful method for developing novel fatigue resistant materials.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · High-Velocity Impact and Material Behavior · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
2. The correlation of the indentation size effect measured with indenters of various shapes10.1016/S0022-5096(01)00103-X ↗
3. Indentation size effect in polycrystalline FCC metals10.1016/S1359-6454(02)00175-1 ↗
4. The indentation size effect: a critical examination of experimental observations and mechanistic interpretations10.1146/annurev-matsci-070909-104456 ↗
5. Sample dimensions influence strength and crystal plasticity10.1126/science.1098993 ↗
6. Size-affected single-slip behavior of pure nickel microcrystals10.1016/j.actamat.2005.05.023 ↗
7. A methodology to investigate size scale effects in crystalline plasticity using uniaxial compression testing10.1016/j.msea.2005.03.082 ↗
8. Plasticity in small-sized metallic systems: intrinsic versus extrinsic size effect10.1016/j.pmatsci.2011.01.005 ↗
9. Micro-compression testing: a critical discussion of experimental constraints10.1016/j.msea.2009.01.005 ↗
10. A further step towards an understanding of size-dependent crystal plasticity: in situ tension experiments of miniaturized single-crystal copper samples10.1016/j.actamat.2007.10.015 ↗
11. Micro-and nanoscale tensile testing of materials10.1007/s11837-009-0037-3 ↗
12. Mechanical properties of micro-sized copper bending beams machined by the focused ion beam technique10.1016/j.actamat.2005.05.036 ↗
13. Micro-bending tests: a comparison between three-dimensional discrete dislocation dynamics simulations and experiments10.1016/j.actamat.2007.12.053 ↗
14. The mechanical size effect as a mean-field breakdown phenomenon: example of microscale single crystal beam bending10.1016/j.actamat.2009.11.031 ↗
15. A microcantilever investigation of size effect, solid-solution strengthening and second-phase strengthening for prism slip in alpha-Ti10.1016/j.actamat.2011.06.005 ↗
16. Stress-controlled fatigue behaviour of micro-sized polycrystalline copper wires10.1016/j.msea.2009.02.037 ↗
17. Anomalous plasticity in the cyclic torsion of micron scale metallic wires10.1103/PhysRevLett.110.244301 ↗
18. Damage evolution during cyclic tension–tension loading of micron-sized Cu lines10.1016/j.actamat.2013.12.006 ↗
19. Cyclic bending experiments on free-standing Cu micron lines observed by electron backscatter diffraction10.1016/j.actamat.2014.10.012 ↗
20. Elastic limit and strain hardening of thin wires in torsion10.1103/PhysRevLett.103.155501 ↗
21. Yield and plastic flow of soft metals in small volumes loaded in tension and flexure10.1080/14786435.2012.685967 ↗
22. Fatigue crack growth behavior of micro-sized specimens prepared from an electroless plated Ni-P amorphous alloy thin film10.2320/matertrans.42.68 ↗
23. Cyclic response of copper single crystal micro-beams10.1016/j.scriptamat.2010.05.014 ↗
24. Structural instabilities during cyclic loading of ultrafine-grained copper studied with micro bending experiments10.1016/j.actamat.2016.11.040 ↗
25. Small scale mechanical testing of irradiated materials10.1557/jmr.2015.26 ↗
26. Proton irradiation creep of thin foil specimens of type 304 austenitic stainless steel and the thickness effects on their mechanical properties10.1016/0022-3115(84)90624-X ↗
27. The effects of grain and specimen sizes on mechanical properties of type 316 austenitic stainless steel10.1016/0022-3115(85)90199-0 ↗
28. Specimen size effects on mechanical properties of 14MeV neutron irradiated metals10.1016/0022-3115(88)90526-0 ↗
29. Specimen size effects on tensile properties of neutron-irradiated steels10.1016/0022-3115(91)90113-L ↗
30. Specimen size effects on the tensile properties of JPCA and JFMS10.1016/S0022-3115(00)00245-2 ↗
31. Evaluation of irradiation effects on fracture strength of silicon carbide using micropillar compression tests10.1007/s11340-012-9678-1 ↗
32. Development and testing of microcompression for post irradiation characterization of ODS steels10.1016/j.jnucmat.2013.09.025 ↗
33. Determination of mechanical properties of copper at the micron scale10.1002/adem.200600129 ↗
34. Source truncation and exhaustion: insights from quantitative in situ TEM tensile testing10.1021/nl201890s ↗
35. Dislocation-induced crystal rotations in micro-compressed single crystal copper columns10.1007/s10853-008-2531-3 ↗
36. Investigation of specimen size effects by in-situ microcompression of equal channel angular pressed copper10.1016/j.msea.2015.09.110 ↗
37. Size‐dependent fracture mode transition in copper nanowires10.1002/smll.201101911 ↗
38. Approaching the theoretical elastic strain limit in copper nanowires10.1021/nl201233u ↗
39. Tensile deformation of electroplated copper nanopillars10.1080/14786435.2010.505180 ↗
40. Microstructure versus size: mechanical properties of electroplated single crystalline Cu nanopillars10.1103/PhysRevLett.104.135503 ↗
41. Higher compressive strengths and the Bauschinger effect in conformally passivated copper nanopillars10.1016/j.actamat.2012.03.013 ↗
42. Influence of homogeneous interfaces on the strength of 500nm diameter Cu nanopillars10.1021/nl2003076 ↗
43. Emergence of strain-rate sensitivity in Cu nanopillars: transition from dislocation multiplication to dislocation nucleation10.1016/j.actamat.2011.05.038 ↗
44. Strain rate effects on the mechanical response in multi-and single-crystalline Cu micropillars: grain boundary effects10.1016/j.ijplas.2013.03.009 ↗
45. Yield stress influenced by the ratio of wire diameter to grain size–a competition between the effects of specimen microstructure and dimension in micro-sized polycrystalline copper wires10.1080/14786435.2012.693215 ↗
46. In situ nanocompression testing of irradiated copper10.1038/nmat3055 ↗
47. Helium implantation effects on the compressive response of Cu nanopillars10.1002/smll.201201614 ↗
48. H. Höppel, M. Brunnbauer, H. Mughrabi, Cyclic deformation behaviour of ultrafine grain size copper produced by equal channel angular extrusion, Materials Week 2000, 25–28 September 2000, Werkstoffwoche-Partnerschaft (ed.), Frankfurt, 〈http://www.materialsweek.org/proceedings〉, 2001.
49. The cyclic hardening and saturation behaviour of copper single crystals10.1016/0025-5416(78)90174-X ↗
50. Cyclic softening of ultrafine grain copper10.1016/S0921-5093(97)00689-8 ↗
51. Microstructural study of the parameters governing coarsening and cyclic softening in fatigued ultrafine-grained copper10.1080/01418610208235689 ↗
52. Deformation behaviour of ultra-fine-grained copper10.1016/0956-7151(94)90326-3 ↗
53. Structure and mechanical properties of ultrafine-grained metals10.1016/S0921-5093(97)00183-4 ↗
54. Observations and issues on mechanisms of grain refinement during ECAP process10.1016/S0921-5093(00)00978-3 ↗
55. Markus, Aicheler. Surface Phenomena Associated with Thermal Cycling of Copper and their Impact on the Service Life of Particle Accelerator Structures, Diss. Ruhr U., Bochum, 2010.
56. Recent developments in irradiation-resistant steels10.1146/annurev.matsci.38.060407.130315 ↗
57. Irradiation creep of oxide dispersion strengthened (ODS) steels for advanced nuclear applications10.1016/j.jnucmat.2009.03.025 ↗
58. Oxide dispersion-strengthened steels: a comparison of some commercial and experimental alloys10.1016/j.jnucmat.2005.01.017 ↗
59. Overview on established and novel FIB based miniaturized mechanical testing using in-situ SEM10.3139/146.110149 ↗
60. 1968
61. P. Schwarzkopf Plansee, Bar Grain Class 6 ODS Iron Alloy Sheet, material property datasheet, Material No.: 1.4768, Abbreviated DIN name: CrAI, 21(6), 2000.
62. Fatigue behaviour of ODS ferritic-martensitic Eurofer steel10.1016/j.proeng.2010.03.077 ↗
63. Low cycle fatigue properties of ODS ferritic-martensitic steels at high temperature10.1016/j.jnucmat.2007.03.020 ↗