journal article·2016-06

Heterogeneities in local plastic flow behavior in a dissimilar weld between low-alloy steel and stainless steel

Fanny Mas, Guilhem Martin, Pierre Lhuissier, Yves Bréchet, Catherine Tassin, François Roch, Patrick Todeschini, Aude Simar

Publisher page

Abstract

Abstract In dissimilar welds between low-alloy steel and stainless steel, the post-weld heat-treatment results in a high variety of microstructures coexisting around the fusion line, due to carbon diffusion and carbides dissolution/precipitation. The local constitutive laws in the vicinity of the fusion zone were identified by micro tensile specimens for the sub-millimeter sized zones, equivalent bulk materials representing the decarburized layer using both wet H2 atmosphere and diffusion couple, and nano-indentation for the carburized regions (i.e. the martensitic band and the austenitic region). The decarburized zone presents only 50% of the yield strength of the low-alloy steel heat affected zone and a ductility doubled. The carburized zones have a yield strength 3–5 times higher than that of the low-alloy steel heat affected zone and have almost no strain hardening capacity. These properties result in heterogeneous plastic deformation happening over only millimeters when the weld is loaded perpendicularly to the weld line, affecting its overall behavior. The constitutive laws experimentally identified were introduced as inputs into a finite elements model of the transverse tensile test performed on the whole dissimilar weld. A good agreement between experiments and simulations was achieved on the global stress-strain curve. The model also well predicts the local strain field measured by microscale DIC. A large out-of-plane deformation due to the hard carburized regions has also been identified.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Fusion-boundary macrosegregation in dissimilar-filler welds
2. Austenitic stainless steel-ferritic steel weld joint failures
3. Technical note: Martensite formation in austenitic/ferritic dissimilar alloy welds
4. Direct TEM observation of microstructures of the austenitic/carbon steels welded joint10.1007/BF00587687 ↗
5. Microstructural transformations in austenitic-ferritic transition joints10.1007/BF01153967 ↗
6. Carbon migration in 5Cr-0.5 Mo/21Cr-12Ni dissimilar metal welds10.1007/s11661-998-0211-1 ↗
7. Modelling of friction stir welding of 7xxx aluminium alloys10.1016/j.msea.2007.02.070 ↗
8. Torque, temperature and hardening precipitation evolution in dissimilar friction stir welds between 6061-T6 and 2014-T6 aluminum alloys10.1016/j.jmatprotec.2013.01.001 ↗
9. Microstructural and mechanical characterization of radial friction welded supermartensitic stainless steel joints10.1016/j.msea.2013.08.014 ↗
10. Local mechanical properties of a dissimilar metal welded joint in nuclear powersystems10.1016/j.msea.2013.01.037 ↗
11. Asymmetric mechanical properties and tensile behaviour prediction of aluminium alloy 5083 friction stir welding joints10.1016/j.msea.2012.12.014 ↗
12. Local property characterization of friction stir welded Ti-5111: transverse orientation measurements10.1016/j.actamat.2013.01.065 ↗
13. Effects of mechanical heterogeneity on the tensile and fatigue behaviours in a laser-arc hybrid welded aluminium alloy joint10.1016/j.matdes.2014.08.050 ↗
14. “Multiscale analysis of the strength and ductility of AA 6056 aluminum friction stir welds,”10.1007/s11661-007-9121-x ↗
15. Influence of the silicon content on the mechanical properties of AA6xxx laser welds10.1016/j.msea.2008.11.033 ↗
16. A study on heat affected zone softening in resistance spot welded dual phase steel by nanoindentation10.1007/s10853-009-4141-0 ↗
17. Computational modeling of the forward and reverse problems in instrumented sharp indentation10.1016/S1359-6454(01)00295-6 ↗
18. Determination of plastic properties of metals by instrumented indentation using different sharp indenters10.1016/S1359-6454(02)00568-2 ↗
19. Local mechanical properties of the 6061-T6 aluminium weld using micro-traction and instrumented indentation10.1016/j.euromechsol.2010.12.007 ↗
20. Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings10.1016/j.msea.2012.11.077 ↗
21. Experimental characterization of the local strain field in a heterogeneous elastoplastic material10.1016/0956-7151(94)90452-9 ↗
22. “Caractérisation de la répartition de la déformation dans les matériaux hétérogènes10.1016/j.mecind.2003.09.002 ↗
23. Characterization of the high temperature strain partitioning in duplex steels10.1007/s11340-012-9628-y ↗
24. Microscale plastic strain heterogeneity in slip dominated deformation of magnesium alloy containing rare earth10.1016/j.msea.2014.01.102 ↗
25. Local plastic-strain heterogeneities and their impact on the ductility of Mg
26. Metallurgical characterization of coupled carbon diffusion and precipitation in dissimilar steel welds10.1007/s10853-016-9792-z ↗
27. Strain softening, slip localization and propagation: From simulations to continuum modelling10.1016/1359-6454(96)00115-2 ↗
28. Influence of strain-rate sensitivity on necking under uniaxial tension10.1016/0001-6160(77)90168-7 ↗
29. Pickering · 1978 · 63
30. The effect of grain size on the stress-strain relationship in low-carbon steel
31. Effects of strengthening mechanisms on sulfide stress cracking resistance of low strength steels10.2355/isijinternational.33.1190 ↗
32. “User”s manual Abaqus.” Providence RI, 2013.