journal article·2019-01

Strengthening mechanisms in an ultrafine grained powder metallurgical hot work tool steel produced by high energy mechanical milling and spark plasma sintering

Faraz Deirmina, Massimo Pellizzari

Publisher page

Abstract

Abstract The strengthening mechanisms in an ultrafine grained (UFG) powder metallurgical (PM) tool steel produced by high energy mechanical milling (MM) and spark plasma sintering (SPS) have been investigated. In order to gain a proper insight to the Hall-Petch relation, bimodal grain size microstructures were produced by mixing different fractions of the nanocrystalline (NC) MM and the coarse grain (CG) gas-atomized powders to achieve different equivalent grain sizes. Dislocation strengthening (~ 435 MPa) and Hall-Petch strengthening (~ 388 MPa) are the major contributing mechanisms in strengthening the as-sintered steel. The presence of 34 vol% retained austenite (RA) had a negative influence on the strength (~ 555 MPa) and highlights the need of heat treatments (i.e., quenching and tempering) to achieve a fully tempered martensitic microstructure with a dispersion of fine secondary carbides. Recovery of dislocations and defects accompanying the precipitation of carbides reduces the effect of grain size (i.e., martensite packet size) on the strength after tempering. However, dislocations acting as preferential sites for secondary carbides nucleation during tempering, provide a finer and more homogenous particles dispersion compared to the CG counterpart. In this condition, the strength is mainly governed by the carbides size and distribution (~ 210 MPa) confirming that the indirect beneficial effects of MM can still be observed after heat treatment.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (64)

Show source-provided references
1. Structural nanocrystalline materials: an overview10.1007/s10853-006-0609-3 ↗
2. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
3. The synthesis and structure of nanocrystalline materials produced by mechanical attrition: a review10.1016/0965-9773(93)90016-5 ↗
4. Nanocrystalline metals prepared by high-energy ball milling10.1007/BF02646980 ↗
5. Koch · 2006
6. Preparation of bulk ultrafine-grained and nanostructured Zn, Al and their alloys by in situ consolidation of powders during mechanical attrition10.1016/S1359-6462(02)00048-9 ↗
7. Microstructural changes during annealing of work-hardened mechanically milled metallic powders (overview)10.2320/matertrans1989.36.289 ↗
8. Grain growth behavior of cryomilled INCONEL 625 powder during isothermal heat treatment10.1007/s11661-002-0011-y ↗
9. In situ characterization of microstructural instabilities: recovery, recrystallization and abnormal growth in nanoreinforced steel powder10.1016/j.actamat.2014.11.051 ↗
10. Stabilization of nanocrystalline grain sizes by solute additions10.1007/s10853-008-2870-0 ↗
11. Nanostructured materials: basic concepts and microstructure10.1016/S1359-6454(99)00285-2 ↗
12. Fabrication of bulk nanocrystalline Fe–C alloy by spark plasma sintering of mechanically milled powder10.1016/j.scriptamat.2005.05.039 ↗
13. Spark plasma co-sintering of mechanically milled tool steel and high speed steel powders10.3390/ma9060482 ↗
14. Structure and properties of ultrafine-grained CoCrFeMnNi high-entropy alloys produced by mechanical alloying and spark plasma sintering10.1016/j.jallcom.2016.12.010 ↗
15. The effect of electric field and pressure on the synthesis and consolidation of materials: a review of the spark plasma sintering method10.1007/s10853-006-6555-2 ↗
16. Cryomilled nanostructured materials: processing and properties10.1016/j.msea.2007.06.099 ↗
17. Influence of iron oxide particles on the strength of ball-milled iron10.2320/matertrans.47.1508 ↗
18. Characterization of nanocrystalline ferrite produced by mechanical milling of pearlitic steel10.1016/j.scriptamat.2004.10.020 ↗
19. Effect of deep cryogenic treatment on the mechanical properties of tool steels10.1016/S0924-0136(01)00973-6 ↗
20. High-temperature properties and microstructural stability of hot-work tool steels10.1016/j.msea.2009.06.010 ↗
21. Practical applications of hotisostatic pressing diagrams: four case studies10.1007/BF02651618 ↗
22. Fedrizzi · 2013
23. Deirmina · 2017
24. On the yield strength of quenched low-carbon lath martensite
25. The relation between microstructure and yield strength in tempered low-carbon lath martensite with 5% nickel10.1179/030634576790431868 ↗
26. Bimodally grained high-strength Fe fabricated by mechanical alloying and spark plasma sintering10.1016/j.actamat.2009.03.034 ↗
27. B962-08, Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes' Principle - MADCAD.com, (n.d.). 〈http://www.madcad.com/library/ASTM-B962-08/〉 (Accessed 5 August 2016).
28. Combined texture and structure analysis of deformed limestone from time-of-flight neutron diffraction spectra10.1063/1.364220 ↗
29. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray debye-scherrer spectrum
30. Stacking faults in face-centred cubic metals and alloys
31. Flow stress analysis of TWIP steel via the XRD measurement of dislocation density10.1016/j.msea.2010.01.033 ↗
32. ASTM E92 - 82, Standard Test Method for Vickers Hardness of Metallic Materials, (n.d.). 〈http://www.astm.org/DATABASE.CART/HISTORICAL/E92-82R03.htm〉 (Accessed 3 September 2016).
33. On the measurement of stress–strain curves by spherical indentation10.1016/S0040-6090(01)01439-0 ↗
34. Spherical indentation of elastic–plastic solids10.1098/rspa.1999.0423 ↗
35. Production of a powder metallurgical hot work tool steel with harmonic structure by mechanical milling and spark plasma sintering10.1007/s11661-017-3957-5 ↗
36. H13–partially stabilized zirconia nanocomposites fabricated by high-energy mechanical milling and selective laser melting10.1016/j.matdes.2018.03.017 ↗
37. Estimation of cooling rates during close-coupled gas atomization using secondary dendrite arm spacing measurement10.1007/s11663-013-9856-2 ↗
38. Voort · 1984 · 1984 · 752
39. Hydrogen-enhanced-plasticity mediated decohesion for hydrogen-induced intergranular and “quasi-cleavage” fracture of lath martensitic steels10.1016/j.jmps.2017.12.016 ↗
40. Effects of nanocrystalline and ultrafine grain sizes on constitutive behavior and shear bands in iron10.1016/S1359-6454(03)00169-1 ↗
41. Effect of pre-existed austenite on austenite reversion and mechanical behavior of an Fe-0.2C-8Mn-2Al medium Mn steel10.1016/j.actamat.2018.01.009 ↗
42. Multiscale modeling of tempering of AISI H13 hot-work tool steel – Part 1: prediction of microstructure evolution and coupling with mechanical properties10.1016/j.commatsci.2015.11.020 ↗
43. The morphology and crystallography of lath martensite in Fe-C alloys10.1016/S1359-6454(02)00577-3 ↗
44. The evolution of dislocation density during heat treatment and creep of tempered martensite ferritic steels10.1016/S1359-6454(03)00324-0 ↗
45. Tempering of lath martensite in low and medium carbon steels: assessment and challenges10.1002/srin.201700038 ↗
46. Austenite grain size and the martensite-start temperature10.1016/j.scriptamat.2008.11.043 ↗
47. Kinetics of the austenite→martensite transformation10.1007/BF03398922 ↗
48. Retained austenite and tempered martensite embrittlement10.1007/BF02646396 ↗
49. The deformation of plastically non-homogeneous materials10.1080/14786437008238426 ↗
50. Steels: Microstructure and Properties - 3rd Edition, (n.d.). 〈https://www.elsevier.com/books/steels-microstructure-and-properties/bhadeshia/978-0-7506-8084-4〉 (Accessed 13 March 2018).
51. Winchell · 1962
52. Martensite in steel: strength and structure10.1016/S0921-5093(99)00288-9 ↗
53. Pickering · 1978
54. Atom probe study of the carbon distribution in a hardened martensitic hot-work tool steel X38CrMoV5-110.1016/j.micron.2012.02.005 ↗
55. The influence of austenite strength upon the austenite-martensite transformation in alloy steels10.1007/BF02641994 ↗
56. Direct or indirect: influence of type of retained austenite decomposition during tempering on the toughness of a hot-work tool steel10.1016/j.msea.2012.11.105 ↗
57. A model for the microstructure behaviour and strength evolution in lath martensite10.1016/j.actamat.2015.07.018 ↗
58. Effect of block size on the strength of lath martensite in low carbon steels10.1016/j.msea.2005.12.048 ↗
59. Effect of austenite grain size on the morphology and crystallography of lath martensite in low carbon steels10.2355/isijinternational.45.91 ↗
60. Comments on the microstructure and properties of ultrafine grained steel10.2355/isijinternational.48.1063 ↗
61. The effect of structure on the deformation of as-quenched and tempered martensite in an Fe-0.2 pct C alloy10.1007/BF02644037 ↗
62. Influence of alloying elements on the hall-petch coefficient in ferritic steel10.4028/www.scientific.net/MSF.706-709.181 ↗
63. Understanding the factors controlling the hardness in martensitic steels10.1016/j.scriptamat.2015.08.010 ↗
64. J. Sjöström, Chromium martensitic hot-work tool steels: damage, performance and microstructure, 2004. 〈http://www.diva-portal.org/smash/record.jsf?Pid=diva2:24899〉 (Accessed 4 April 2017).