journal article·2017-05

Mechanical properties and microstructure of ultrafine grained commercial purity aluminium prepared by cryo-hydrostatic extrusion

Wacek Pachla, Mariusz Kulczyk, Julita Smalc-Koziorowska, Monika Wróblewska, Jacek Skiba, Sylwia Przybysz, Mariusz Przybysz

Publisher page

Abstract

Abstract CP 99.5% aluminium was processed by cryo-hydrostatic extrusion with true strains up to 3.4 in one pass. The aim was to refine its microstructure and improve its mechanical properties. The properties of the thus processed material were compared with those obtained after the same process but run at room temperature. Cooling the billet with liquid nitrogen combined with water cooling of the extruded wire enabled suppressing partially the dynamic and static structural processes. The grain size was reduced to ~400 nm in the cryo-extrusion, and to ~450 nm in the room-extrusion. In the cryo-extrusion the increase of the yield strength to 168 MPa and the hardness to 56HV0.2 with the respective reduction of the elongation to fracture to 13.6% were obtained. The cryo-cooling effectiveness and the influence of the adiabatic heat generated during the plastic processing on the structure, mechanical properties, hardness, and tensile impact toughness just after hydrostatic extrusion, an also after the post deformation annealing are discussed. In view of the intensive adiabatic heating amounting to 0.57Tm no special improvement of the mechanical properties after the post-deformation annealing was observed. The cryo-cooling became effective at the true strain e>2, where the extrusion pressures clearly differed from the room-extrusion pressures and the defect density substantially increased. After the cryo-hydrostatic extrusion the mechanical properties were comparable to the highest values reported in the literature for cryo-rolling but, since they were obtained in a single deformation step and with twice as large subgrains, the ductility of the extruded aluminium was higher. During the cryo-hydrostatic extrusion conducted at high strains the reduction in ductility of the aluminium is hindered and thanks to the beneficial role of the hydrostatic stress active in the material the structural and mechanical effects which occur during severe plastic deformation are enhanced.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. Effect of grain size on corrosion of high purity aluminium10.1016/j.electacta.2010.09.023 ↗
2. Microstructure and mechanical properties of cryo-rolled AA6061 Al alloy10.1016/S1003-6326(16)64083-9 ↗
3. Natural aging behavior of AA7050 Al alloy after cryogenic rolling10.1016/j.msea.2013.11.017 ↗
4. Production of ultrafine grain sizes in aluminium sheets by severe plastic deformation using the technique of groove pressing10.1016/j.scriptamat.2005.03.001 ↗
5. Mechanical properties and microstructural evolution of Al 6061 alloy processed by multidirectional forging at liquid nitrogen temperature10.1016/j.matdes.2013.10.045 ↗
6. Effect of the grain refinement via severe plastic deformation on strength properties and deformation behavior of an Al6061 alloy at room and cryogenic temperatures10.1016/j.matlet.2011.06.057 ↗
7. Nanocrystalline Al–Mg alloy with ultrahigh strength and good ductility10.1016/j.scriptamat.2005.09.028 ↗
8. Mechanical properties of aluminium–copper–lithium alloy AA2195 at cryogenic temperatures10.1016/j.matdes.2014.02.024 ↗
9. Tensile behavior of 3104 aluminum alloy processed by homogenization and cryogenic treatment10.1016/S1003-6326(14)63370-7 ↗
10. Hailiang Yu, Cheng Lu, Kiet Tieu, Xianghua Liu, Yong Sun, Qingbo Yu, Charlie Kong, Asymmetric cryorolling for fabrication of nanostructural aluminum sheets, Scientific Reports 2 : 772 | 〈DOI: 10.1038/srep00772〉.10.1038/srep00772 ↗
11. Strain rate effect on the cyclic deformation response of UFG Al alloys10.1016/j.msea.2012.03.085 ↗
12. Cyclic deformation response of ultrafine pure Al10.1016/j.actamat.2011.05.013 ↗
13. Roll-formability of cryo-rolled ultrafine aluminium sheet10.1016/j.matdes.2014.06.036 ↗
14. Studies on void coalescence analysis of nanocrystalline cryorolled commercially pure aluminium formed under different stress conditions10.1016/j.matdes.2010.01.056 ↗
15. Effect of cryo-rolling and annealing on microstructure and properties of commercially pure aluminium10.1016/j.msea.2005.03.026 ↗
16. Formability of cryo-rolled aluminium in uniaxial and biaxial tension10.1016/j.msea.2012.06.044 ↗
17. Effects of warm rolling and ageing after cryogenic rolling on mechanical properties and microstructure of Al 6061 alloy10.1016/j.matdes.2012.02.010 ↗
18. A comparative study on mechanical properties of ultrafine-grained Al 6061 and Al 6063 alloys processed by cryorolling10.1007/s12666-008-0028-z ↗
19. Localized corrosion of an ultrafine grained Al–4Zn–2Mg alloy produced by cryorolling10.1016/j.corsci.2012.04.009 ↗
20. Effect of cryorolling on the mechanical properties of AA5083 alloy and the Portevin-Le Chatelier phenomenon10.1016/j.matdes.2014.11.022 ↗
21. Study on cryorolled Al–Cu alloy using X-ray diffraction line profile analysis and evaluation of strengthening mechanisms10.1016/j.matdes.2013.05.095 ↗
22. Effect of cryorolling on microstructure of Al–Mg–Si alloy10.1016/j.matlet.2008.01.003 ↗
23. Development of ultrafine-grained Al 6063 alloy by cryorolling with the optimized initial heat treatment conditions10.1016/j.matdes.2010.11.027 ↗
24. Experimental investigations on microstructure and formability of cryorolled AA 5052 sheets10.1016/j.matdes.2013.08.008 ↗
25. Development of ultrafine grained high strength Al–Cu alloy by cryorolling10.1016/j.scriptamat.2006.03.012 ↗
26. Simultaneously increasing the ductility and strength of nanostructured alloys10.1002/adma.200600310 ↗
27. Effect of annealing temperature on microstructures and mechanical properties of a 5083 Al alloy deformed at cryogenic temperature10.1016/j.scriptamat.2004.02.037 ↗
28. The effect of cryogenic temperature and change in deformation mode on the limiting grain size in a severely deformed dilute aluminium alloy10.1016/j.actamat.2007.12.017 ↗
29. W. Pachla, M. Kulczyk, A. Świderska-Środa, M. Lewandowska, H. Garbacz, A. Mazur, K.J. Kurzydłowski, Nanostructuring of metals by hydrostatic extrusion, in: Proceedings of the 9th International Conference on Mat. Forming ESAFORM-2006, Glasgow, UK, 26–28 April, 535–538, 2006.
30. Recent development in grain refinement by hydrostatic extrusion10.1007/s10853-008-2810-z ↗
31. Effect of severe plastic deformation realized by hydrostatic extrusion and rotary swaging on the properties of CP Ti grade 210.1016/j.jmatprotec.2015.02.027 ↗
32. Nanostructurization of 316L type austenitic stainless steels by hydrostatic extrusion10.1016/j.msea.2014.07.069 ↗
33. UFG and nanocrystalline microstructures produced by hydrostatic extrusion of multifilament wires10.3139/146.110142 ↗
34. Pugh · 1970
35. Microstructural path and temperature dependence of recrystallization in commercial aluminium10.1016/S1359-6454(01)00074-X ↗
36. Image based analysis of complex microstructures of engineering materials10.2478/v10006-008-0003-1 ↗
37. Strength and ductility of 316L austenitic stainless steel strengthened by nano-scale twin bundles10.1016/j.actamat.2011.11.009 ↗
38. Hall-Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys10.1016/S0921-5093(03)00008-X ↗
39. Strengthening mechanisms in nanostructured high-purity aluminium deformed to high strain and annealed10.1016/j.actamat.2009.05.017 ↗
40. Change in microstructure and mechanical properties of ultra-fine grained aluminum during annealing10.2320/jinstmet1952.64.6_429 ↗
41. Strength and ductility of ultrafine grained aluminum and iron produced by ARB and annealing10.1016/S1359-6462(02)00282-8 ↗
42. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗
43. The tensile behavior and deformation microstructure of cryo-rolled and annealed pure nickel10.1016/j.msea.2005.07.045 ↗
44. Dependence of strength, elongation, and toughness on grain size in metallic structural materials10.1063/1.2720184 ↗
45. 〈http://www.matweb.com/〉 (last (accessed 25.02.17).
46. Fatigue crack growth rate in ultrafine-grained Al 5483 and 7475 alloys processed by hydro-extrusion10.1016/j.mechmat.2013.07.005 ↗
47. Tailoring microstructure and mechanical properties of 6063 aluminium alloy for lightweight structural parts10.4028/www.scientific.net/MSF.765.388 ↗
48. Microstructure and mechanical properties of AA5483 treated by a combination of ECAP and Hydrostatic Extrusion10.2478/amm-2014-0026 ↗
49. Optimizing the strength and ductility of fine structured 2024 Al alloy10.1016/j.actamat.2007.06.043 ↗
50. Development of high strength Al–Mg–Si AA6061 alloy through cold rolling and ageing10.1016/j.msea.2009.03.077 ↗
51. Effect of rolling temperature on microstructure and mechanical properties of 6063 Al alloy10.1016/j.msea.2008.03.029 ↗