Grain refinement and stabilization in spray-formed AISI 1020 steel
Source abstract
Abstract
Abstract An AISI 1020-grade mild steel, with a small amount of aluminum, was spray-formed by nitrogen gas-atomization and deposition. The spray-formed 1020 steel contained 0.05 mass% of nitrogen and 0.06 mass% of aluminum. Rolling the spray deposit at 1123 K for a thickness reduction of 70% and subsequent normalizing at low austenitic temperatures produced a fully dense steel having a refined ferrite grain size as small as 3 μm. This grain refinement resulted from the pinning of prior austenite grain boundaries by fine AlN particles which precipitated during the thermomechanical treatments. Room-temperature tensile properties (YS: 550 MPa, UTS: 630 MPa, elongation: 23%), exceeding those of conventional microalloyed high-strength low alloy steels, were achieved in the normalized state. The AlN-pinned fine-grained microstructure survived subsequent re-austenizing at temperatures as high as 1273 K. When tensile-tested in the austenite region at 1123 K, the microalloyed 1020 steel showed a large elongation exceeding 200%.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Metal and Thin Film Mechanics · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Baird · 1973 · 1
2. F.B. Pickering, in: M. Korchynski (Ed.), Microalloying 75, Union Carbide Corporation, New York, 1977, p. 9 (distributed by ASM Metals Park, OH).
3. T. Gladman, D. Dulieu, I.D. McVor, in: M. Korchynski (Ed.), Microalloying 75, Union Carbide Corporation, New York, 1977, p. 32 (distributed by ASM Metals Park, OH).
4. L. Meyer, F. Heisterkamp, W. Mueschenborn, in: M. Korchynski (Ed.), Microalloying 75, Union Carbide Corporation, New York, 1977, p. 153 (distributed by ASM Metals Park, OH).
5. Leslie · 1981 · 189
6. Honeycombe · 1981 · 166
7. Zhou · ISIJ Int. · 1996 · 36 · 139710.2355/isijinternational.36.1397 ↗
8. Wright · J. Iron Steel Inst. · 1962 · 200 · 299
9. Kuziak · 1992 · 51
10. Leslie · Trans. ASM · 1954 · 46 · 1470
11. Singer · Met. Mater. · 1970 · 4 · 245
12. Annavarapu · Metall. Trans. A · 1988 · 19A · 307710.1007/BF02647735 ↗
13. Lavernia · J. Mater. Sci. Eng. · 1988 · 98 · 38110.1016/0025-5416(88)90191-7 ↗
14. Bewley · Mater. Sci. Eng. · 1989 · A118 · 20710.1016/0921-5093(89)90072-5 ↗
15. Ferguson · 1984 · 7 · 531
16. Grant · 1988 · 203
17. Grant · Metall. Trans. A · 1992 · 23A · 108310.1007/BF02665040 ↗
18. Harada · Mater. Sci. Eng. · 1991 · A133 · 78010.1016/0921-5093(91)90185-P ↗
19. Rai · J. Met. · 1985 · 37 · 22
20. Gladman · J. Iron Steel Inst. · 1967 · 205 · 653
21. Chauerjea · Metal Treat. · 1957 · 24 · 54
22. Hall · J. Iron Steel Inst. · 1967 · 205 · 309
23. Willson · Int. Mat. Rev. · 1988 · 33 · 22110.1179/imr.1988.33.1.221 ↗
24. Croft · Met. Tech. · 1983 · 10 · 12510.1179/030716983803291596 ↗
25. Grance · Metall. Trans. · 1971 · 2 · 6510.1007/BF02662639 ↗
26. Honer · 1977
27. Hannerz · Met. Sci. J. · 1968 · 2 · 14810.1179/030634568790443260 ↗
28. Pehlke · Trans. AIME · 1963 · 227 · 844
29. Elliott · 1985 · 294
30. Joint Committee on Powder Diffract ion Standards, International Center for Diffraction Data, Swarthmore, PA, 1975, Card No. 25–1133.
31. Smith · 1981 · 101
32. Wada · Metall. Trans. B · 1978 · 9B · 44110.1007/BF02654419 ↗
33. Darken · Trans. AIME · 1951 · 191 · 1174
34. Michalak · Trans. AIME · 1968 · 242 · 1149
35. Richards · J. Aust. Inst. Metals · 1967 · 12 · 2
36. Gladman · Heat Treat. Metals · 1994 · 1 · 11
37. Gao · ISIJ Int. · 1998 · 38 · 74410.2355/isijinternational.38.744 ↗
38. Gladman · Proc. Roy. Soc. Ser. A · 1966 · 295 · 29810.1098/rspa.1966.0208 ↗
39. Manohar · ISIJ Int. · 1998 · 38 · 91310.2355/isijinternational.38.913 ↗