journal article·2013-09

Influence of heat treatment on microstructure and tensile property of a new high strength beta alloy Ti–2Al–9.2Mo–2Fe

Cheng-Lin Li, Xu-Jun Mi, Wen-Jun Ye, Song-Xiao Hui, Dong-Geun Lee, Yong-Tai Lee

Publisher page

Abstract

Abstract An investigation is given on the influence of heat treatment by the microstructural characteristics and tensile properties of a new high strength alloy Ti–2Al–9.2Mo–2Fe. Both of the α/β and β solution treatment (α/β-ST and β-ST), then aged at temperatures ranging from 400 °C to 600 °C, were prepared. The primary α phases having 2–5 μm are formed during the α/β-ST, and restrain the size of β grains below 10 μm. As a result of the fine β grains, the α/β-ST contributes a higher strength than the β-ST. The co-existence of α″ and athermal ω phase is found in the β-ST and water quenched samples. However, these have little influence on the alloy hardening. After aging, the alloys in the α/β-ST and β-ST condition reveal the phase transformation of β to isothermal ω, and β to α depending on the aging temperature. Although the primary α phase formed during the α/β-ST increases the stability in the β matrix, and the isothermal ω phase also appears to occur during aging at 400 °C and 450 °C for 2 h. These phenomena are less common in beta titanium alloys, when treated in the α/β-ST and aged at lower temperatures. The isothermal ω phase formed in both conditions results in high strength levels (1600 MPa of ultimate strength) with much ductility loss (2.5–4.5% of elongation) as a result of the superior hardening effect and brittleness of ω phase. However, the secondary α phase with the size of 1–3 μm leads to attractive combinations of strength and ductility (1200–1400 MPa of ultimate strength with 7.5–12.5% of elongation). The reason for that is too fine α phase below 1 μm tends to result in ultra-high strength with much ductility loss. As a whole, the alloy can be heat treated to obtain excellent balances of strength and ductility, and provided abundant stress levels with optional ductility as a usable material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Ankem · Mater. Sci. Eng. A · 1999 · 265 · 12710.1016/S0921-5093(98)01170-8 ↗
2. Titanium
3. Wang · Mater. Sci. Eng. A · 1996 · 213 · 13410.1016/0921-5093(96)10243-4 ↗
4. Ankem · 1984 · 107
5. Nyakana · J. Mater. Eng. Perform. · 2005 · 14 · 79910.1361/105994905X75646 ↗
6. Ivasishin · Mater. Sci. Eng. A · 2005 · 405 · 29610.1016/j.msea.2005.06.027 ↗
7. Weiss · Mater. Sci. Eng. A · 1998 · 243 · 4610.1016/S0921-5093(97)00783-1 ↗
8. Ivasishin · J. Alloys Compd. · 2008 · 457 · 29610.1016/j.jallcom.2007.03.070 ↗
9. Schmidt · Metall. Mater. Trans. A · 2011 · 42 · 265210.1007/s11661-011-0662-7 ↗
10. Ohmori · Mater. Sci. Eng. A · 2001 · 312 · 18210.1016/S0921-5093(00)01891-8 ↗
11. Weiss · Mater. Sci. Eng. A · 1998 · 243 · 4610.1016/S0921-5093(97)00783-1 ↗
12. Froes · Key Eng. Mater. · 2010 · 436 · 110.4028/www.scientific.net/KEM.436.1 ↗
13. Cost-Affordable Titanium-Symposium Proceedings
14. Bania · 1993 · 3
15. Kosaka · Wire J. Int. · 2006 · 39 · 87
16. Kocan · J. Mater. Eng. Perform. · 2005 · 14 · 76510.1361/105994905X75583 ↗
17. Kosaka · J. Mater. Eng. Perform. · 2005 · 14 · 79210.1361/105994905X75637 ↗
18. MMPDS 03, Metallic Material Properties Development and Standardization, 2006.
19. Lütjering · 2007
20. Duerig · 1984 · 19
21. M. Morinaga, N. Yukawa, T. Maya, K. Sone, H. Adachi, in: P. Lacombe, R. Tricot, G. Beranger (Eds.), Proceedings of the Sixth World Conference on Titanium, Societe fracaise de Metallurgie, Cannes, France, 1988, pp. 1601–1606.
22. Collings · 1994
23. Bowen · 1984 · 85
24. Leyens · 2003
25. Duerig · Metall. Mater. Trans. A · 1980 · 11 · 198710.1007/BF02655118 ↗
26. Min · Mater. Sci. Eng. A · 2011 · 528 · 456910.1016/j.msea.2011.02.071 ↗
27. Min · Mater. Sci. Eng. A · 2008 · 497 · 7410.1016/j.msea.2008.06.018 ↗
28. Min · Mater. Sci. Eng. A · 2010 · 527 · 549910.1016/j.msea.2010.06.016 ↗
29. Ng · Mater. Sci. Eng. A · 2010 · 527 · 701710.1016/j.msea.2010.07.055 ↗
30. Duerig · 1980 · vol. 2 · 1299
31. Wang · Mater. Sci. Eng. A · 2011 · 528 · 237010.1016/j.msea.2010.12.044 ↗
32. Ivasishin · 2004 · 1227
33. Rhodes · Metall. Mater. Trans. A · 1977 · 8 · 174910.1007/BF02646879 ↗
34. ASTM F 2066-2001, Standard Specification for Wrought Titanium-15 Molybdenum Alloy for Surgical Implant Applications (UNS R58150), 2001.
35. Grosdidier · Scr. Mater. · 1997 · 36 · 2110.1016/S1359-6462(96)00341-7 ↗
36. Bhattacharjee · Metall. Mater. Trans. A · 2006 · 37 · 142310.1007/s11661-006-0087-x ↗
37. Grosdidier · Metall. Mater. Trans. A · 2000 · 31 · 109510.1007/s11661-000-0105-3 ↗
38. Paris · Metall. Mater. Trans. A · 1976 · 7 · 27310.1007/BF02644467 ↗
39. Xu · Scr. Mater. · 2006 · 54 · 194310.1016/j.scriptamat.2006.02.002 ↗
40. Fanning · J. Mater. Eng. Perform. · 2005 · 14 · 78810.1361/105994905X75628 ↗