journal article·2002-12

The effect of strain path reversal during hot rolling on austenitic stainless steel

R.L Higginson, C.M Sellars

Materials Science and Engineering: A· Volume 338· Issue 1-2
Publisher page

Abstract

During flat rolling the metal undergoes complex strain paths due to the interaction of the stock with the rolls. These changes in strain path affect the stored energy and hence the recrystallisation behaviour of the material on annealing. The current paper investigates the effect of the roll pass schedule on the recrystallisation kinetics of type 316L stainless steel. By changing the direction of rolling and the reduction on the second pass the effect of the deformation on the recrystallisation kinetics was determined following static annealing. The effect was found to be at a maximum after lower second pass deformation, with the maximum effect at 0.8 from the centre of the sample half thickness. A forward/forward pass gave an increase in the recrystallisation kinetics at this point with more homogeneous recrystallisation seen after a forward/reverse pass. The origins of these differences were investigated by the study of the sub-structure developed during deformation. The differences in the kinetics cannot be attributed to a single microstructural feature, but to a combination of all of them.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. Lindh · Scripta Metall. · 1976 · 10 · 67310.1016/0036-9748(76)90340-9 ↗
2. Cowan · Mater. Sci. Tech. · 1996 · 11 · 110410.1179/mst.1995.11.11.1104 ↗
3. A.D. Rollet, T. Lowe, U.F. Kocks, M.G. Stout, in: J.S. Kallend, G. Gottstein (Eds.), ICOTOM 8, The Eighth International Conference on Textures of Materials, Met. Soc. Inc., PA (1988) 473–478.
4. M.E. Hargreaves, M.H. Loretto, L. Clarebrough, R.L. Segall, in: NPL Symposium No 15, London, HMSO (1963) 209–215.
5. Hasegawa · Mater. Sci. Eng. · 1975 · 20 · 26710.1016/0025-5416(75)90159-7 ↗
6. Lachmann · Steel Res. · 1991 · 10 · 44710.1002/srin.199100427 ↗
7. McLaren · Mat. Sci. Tech. · 1992 · 8 · 109010.1179/mst.1992.8.12.1090 ↗
8. Kato · Trans. ISIJ · 1984 · 24 · 105010.2355/isijinternational1966.24.1050 ↗
9. Sakai · Trans. ISIJ · 1988 · 28 · 102810.2355/isijinternational1966.28.1028 ↗
10. Black · Mater. Sci. Eng. · 2001 · 17 · 1055
11. C.M. Sellars, Q. Zhu, in: J.B. Bilde-Sorenson (Ed.), Proceedings of the Twentieth Risø International Symposium on Materials Science, Deformation-induced Microstructures: Analysis and Relation to Properties. Riso National Laboratory, Roskilde, Denmark, 1999, pp. 167–182.
12. Y. Choi, M.Phil thesis, The effect of grain size on the mechanical behaviour of 316L stainless steel, The University of Sheffield, 1999.