journal article·2020-07-01Open access

Influence of high-energy shot peening on the microstructure and mechanical properties of Ti–6Al–4V welded joints

He Xiaomei, Song Guodong, Zhu Xiaoya

Materials Research Express· Volume 7· Issue 7

Abstract

Abstract In this study, Ti–6Al–4V welded joints were subjected to a high-energy shot peening (HESP) treatment. The structural characteristics of the Ti–6Al–4V welded joints were investigated by optical microscopy (OM) and x-ray diffraction (XRD). The Rockwell hardness and residual stress in different regions of the Ti–6Al–4V welded joints were assessed before and after treatment. Tension tests were then performed to investigate the effect of HESP on the welded samples. Experimental results showed that an Surface nanocrystallization (SNC) layer can be prepared on a Ti–6Al–4V welded joint via HESP. The average grain size of the SNC layer was approximately 30 nm after HESP. HESP also resulted in a higher surface hardness compared with that of the original sample. After treatment, surface compressive residual stresses formed in welded joints, and the residual peak stress of the weld zone was decreased from 650 MPa to −638 MPa. The surface hardness and surface residual stress were distributed more uniformly on the surface of the welded joint. After treatment, the tensile properties were improved.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Structural Nanocrystalline Materials. Fundamentals and Applications. Von Carl C. Koch, Ilya A. Ovid’ko, Sudipta Seal und Stan Veprek10.1002/ange.200685538 ↗
2. Gleiter · Prog. Mater Sci. · 1989 · 33 · 22310.1016/0079-6425(89)90001-7 ↗
3. Shot peening effect on 904 L welds corrosion resistance10.1016/j.jcsr.2015.08.041 ↗
4. Fatigue strength improvement of 5083 H11 Al-alloy T-welded joints by shot peening: experimental characterization and predictive approach10.1016/j.ijfatigue.2005.02.001 ↗
5. The effect of shot peening on fatigue life of welded tubular joint in offshore structure10.1016/j.matdes.2011.11.024 ↗
6. Magnesium: properties-applications-potential10.1016/S0921-5093(00)01351-4 ↗
7. Mechanical surface treatments on titanium, aluminum and magnesium alloys10.1016/S0921-5093(98)01168-X ↗
8. Surface nanocrystallization treatment of AZ91D magnesium alloy by cold spraying shot peening process10.1016/j.surfcoat.2019.04.093 ↗
9. An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment10.1016/S1359-6454(02)00310-5 ↗
10. Nanocrystalline materials10.1179/imr.1995.40.2.41 ↗
11. Mechanical properties of nanocrystalline materials10.1016/j.pmatsci.2005.08.003 ↗
12. Segregation stabilizes nanocrystalline bulk steel with near theoretical strength10.1103/PhysRevLett.113.106104 ↗
13. Heterogeneous and architectured materials: a possible strategy for design of structural materials10.1002/adem.200700289 ↗
14. Revealing extraordinary intrinsic tensile plasticity in gradient nano-grained copper10.1126/science.1200177 ↗
15. Making strong nanomaterials ductile with gradients10.1126/science.1255940 ↗
16. Inverse temperature dependence of toughness in an ultrafine grain- structure steel10.1126/science.1156084 ↗
17. Formation of nanolaminated structure in an interstitial-free steel10.1016/j.scriptamat.2014.10.003 ↗
18. Characterization and properties of nanocrystalline surface layer in Mg alloy induced by surface mechanical attrition treatment10.1016/j.jallcom.2006.11.079 ↗
19. Wear behavior of nanocrystalline structured magnesium alloy induced by surface mechanical attrition treatment10.1016/j.surfcoat.2014.11.026 ↗
20. Effect of surface mechanical attrition treatment on biodegradable Mg-1Ca alloy10.1016/j.msec.2013.11.010 ↗
21. Surface nanocrystallization of iron induced by ultrasonic shot peening10.1016/S0965-9773(99)00324-4 ↗
22. Microstructure and evolution of mechanically-induced ultrafine grain in surface layer of Al-alloy subjected to USSP10.1016/S1359-6454(02)00051-4 ↗
23. Surface self- nanocrystallization on industrial pure iron by high energy shot peening10.13251/j.issn.0254-6051.2010.05.020 ↗
24. Mechanical surface treatments on titanium, aluminum and magnesium alloys10.1016/S0921-5093(98)01168-X ↗
25. An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel10.1016/S0142-1123(01)00205-5 ↗
26. Influence of shot peening on the fatigue life of laser hardened 17-4Ph steel10.1016/j.ijfatigue.2010.10.010 ↗
27. Experimental study of the microstructure and stress state of shot peened and surface mechanical attrition treated nickel alloys10.1016/j.scriptamat.2009.10.015 ↗
28. The Scherrer equation versus the ‘Debye–Scherrer equation’10.1038/nnano.2011.145 ↗
29. Shot peening effects on residual stresses redistribution of offshore wind monopile multi-pass weldments10.1016/j.marstruc.2019.03.006 ↗
30. Effect of compressive residual stress generated by plastic preload on fatigue initiation of 6061 Al-alloy10.1016/j.prostr.2016.06.386 ↗
31. AISI 4140 steel fatigue performance: Cd replacement by electroplated Zn-Ni Alloy coating10.1007/s11665-020-04669-1 ↗
32. Investigation of residual stress, stress relaxation and work hardening effects induced by shot peening on the fatigue life of AA 6005-T6 aluminum alloy10.1088/2053-1591/ab6c8f ↗
33. Plasma immersion ion implantation and shot peening influence on the fatigue strength of AA 7050-T7451 aluminum alloy10.1088/2631-8695/ab6ac7 ↗