Tribological behavior of extruded spray-forming 2195-T6 Al-Li alloy at different loads using pin-on-disk tribotester
Source abstract
Abstract
Abstract The tribological properties of Al-Li alloys impact the reliability of components used in different industrial sectors. In this research, the effect of normal load on friction and wear properties of the extruded spray-formed 2195-T6 Al-Li alloy is investigated by using a pin-on-disk tester. Through the microstructure of the friction subsurface, it is evaluated that the friction coefficient of 2195 alloy decreases from 0.408 to 0.306 by increasing load (25 N to 150 N), while the wear rate increases exponentially. It is also analyzed that a mild-severe wear transition occurs between 100 N and 125 N and the main wear mechanism gradually shifts from abrasive wear and oxidative wear to delamination wear (25 N ∼ 100 N), and finally attains the state of severe plastic deformation (125 N ∼ 150 N). Under the action of normal load and friction shearing force, the deformation layer in the subsurface increases from 3 μm to 43 μm with increasing load, and the accumulation of strain leads to cracks and holes.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
2. Recent advances in the development of aerospace materials10.1016/j.paerosci.2018.01.001 ↗
3. Mechanical behaviour of aluminium-lithium alloys10.1007/BF02717134 ↗
4. Hot extrusion processing of Al–Li alloy profiles and related issues: a review10.1186/s10033-020-00479-7 ↗
5. Influence of post-weld heat treatment on microstructure and mechanical properties of laser beam welded 2195 Al–Li alloy10.1088/2053-1591/ab1736 ↗
6. Effect of temperature on friction and galling behavior of 7075 aluminum alloy sheet based on ball-on-plate sliding test10.1016/j.triboint.2019.105872 ↗
7. On the enhancement of wear resistance of Al-Mg-Si alloy via micro-alloying Sn10.1007/s12046-021-01655-8 ↗
8. Influence of bioceramic reinforcement on tribological behaviour of aluminium alloy metal matrix composites: experimental study and analysis10.1016/j.jmrt.2021.09.090 ↗
9. Influence of micro B4C ceramic particles addition on mechanical and wear behavior of aerospace grade Al-Li alloy composites10.1007/s12046-020-01543-7 ↗
10. Statistical approach on high temperature dry sliding wear behavior of Al-Li-Si3N4 metal matrix composite10.1007/s12633-021-00995-8 ↗
11. Effects of extrusion parameters and post-heat treatments on microstructures and mechanical properties of extrusion weld seams in 2195 Al-Li alloy profiles10.1016/j.jmrt.2019.12.095 ↗
12. Effects of pre-stretching and aging treatments on microstructure, mechanical properties, and corrosion behavior of spray-formed Al-Li alloy 219510.1007/s11665-020-05142-9 ↗
13. Effect of extrusion parameters on microstructure, texture and mechanical property anisotropy of spray deposited 2195 Al–Li alloy profile10.1016/j.msea.2021.141406 ↗
14. Effects of laser shock peening on microstructures and properties of 2195 Al-Li alloy10.1016/j.jallcom.2018.12.118 ↗
15. Microstructure analysis and low-cycle fatigue behavior of spray-formed Al–Li alloy 2195 extruded plate10.1016/j.msea.2018.11.053 ↗
16. Microstructure and mechanical properties of 2195 alloys prepared by traditional casting and spray forming10.1016/j.msea.2020.139337 ↗
17. Microstructure evolution of spray deposited and as-cast 2195 Al-Li alloys during homogenization10.1016/j.jmst.2020.12.028 ↗
18. Processing and characterization of Al–Cu–Li alloy AA2195 undergoing scale up production through the vacuum induction melting technique10.1016/j.msea.2013.03.054 ↗
19. The influence of cold forging process on the microstructure, porosity and wear behavior of spray formed Al-Si alloys10.1016/j.matpr.2017.11.595 ↗
20. Microstructure evolution and precipitation characteristics of spray-formed and subsequently extruded 2195 Al-Li alloy plate during solution and aging process10.1016/j.jmatprotec.2020.116718 ↗
21. Friction stir welding process of aluminum-lithium alloy 219510.1016/j.proeng.2016.06.639 ↗
22. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
23. Effect of precipitates on mechanical properties of AA219510.1016/j.jallcom.2016.01.229 ↗
24. Effect of different aging processes on the microstructure and mechanical properties of a novel Al–Cu–Li alloy10.1016/j.jmst.2016.01.018 ↗
25. Influence of pre-deformation on aging precipitation behavior of three Al–Cu–Li alloys10.1007/s40195-016-0519-6 ↗
26. Effect of pre-deformation on microstructure and properties of a novel aluminum-lithium alloy
27. Microstructure and mechanical properties of 2195 alloys prepared by traditional casting and spray forming10.1016/j.msea.2020.139337 ↗
28. Microstructures and mechanical properties of spray deposited 2195 Al-Cu-Li alloy through thermo-mechanical processing10.1016/j.msea.2018.04.116 ↗
29. Effects of pre-stretching and aging treatments on microstructure, mechanical properties, and corrosion behavior of spray-formed Al-Li alloy 219510.1007/s11665-020-05142-9 ↗
30. Effect of pre-stretching on microstructure and mechanical properties of spray formed 2195 Al-Li alloy after aging10. 13289 / j. issn. 1009-6264. 2021-0521 ↗
31. Effects of pre-rolling on mechanical properties and fatigue crack growth rate of 2195 Al-Li alloy10.1007/s11771-022-4969-x ↗
32. Oxidative wear kinetics in unlubricated steel sliding contact10.1016/j.triboint.2011.05.021 ↗