journal article·2026-02Open access

3D printed, dissolvable molds for the fabrication of geometrically complex, elastomeric energy absorbers

D.J. Bischoff, M.J. DeGrange, J.M. Morales-Ferrer, A.M. Clay, E.D. Wetzel

Materials & Design· Volume 262

Abstract

Elastomeric, architected energy absorbers are fabricated by fused filament fabrication (FFF) of dissolvable molds, casting and curing elastomeric resins in the mold cavities, and then dissolving the mold. Multiple mold materials and dissolution solvents are considered, with water-soluble, butenediol vinyl alcohol copolymer (BVOH) molds down selected based on compatibility and dissolution rate studies. A diverse set of lattices, springs, and generalized cylindrical shells are fabricated using cast silicone and urethane elastomers with durometers from 20A to 60D, as well as a foamed elastomer lattice and a glassy epoxy lattice. The use of vacuum during casting enables fine features with high geometric accuracy. Comparisons between cast springs and elastomeric springs fabricated directly via FFF show the superior geometric resolution, and mechanical property space, available using this casting approach. Quasistatic and dynamic compression are performed demonstrating a wide range of mechanical responses, including high energy absorption efficiency. Additional hybrid lattices are fabricated using two different polymers within a single, interlocked structure. The results of this study demonstrate that FFF of dissolvable molds can be used to fabricate complex geometry energy absorbers over a wider range of material properties and chemistries, and with superior feature resolution, compared to the direct FFF fabrication of such structures.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Materials and Mechanics · Advanced Sensor and Energy Harvesting Materials · Dielectric materials and actuators

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Research progress on helmet liner materials and structural applications10.3390/ma17112649 ↗
2. Elastomeric microlattice impact attenuators10.1016/j.matt.2019.10.004 ↗
3. Impact response of advance combat helmet pad systems10.1016/j.ijimpeng.2023.104757 ↗
4. A review on additive manufactured engineering materials for enhanced road safety and transportation applications10.3390/polym17070877 ↗
5. Polyurea coatings for enhanced blast-mitigation: a review10.1039/C6RA23866A ↗
6. High energy absorption efficiency and biodegradable polymer based microcellular materials via environmental-friendly CO2 foaming for disposable cushioning packaging10.1016/j.polymer.2023.126612 ↗
7. An experimental study on energy absorption behavior of polyurethane foams10.1177/0731684408094220 ↗
8. Superlative mechanical energy absorbing efficiency discovered through self-driving lab-human partnership10.1038/s41467-024-48534-4 ↗
9. Compression behavior and impact energy absorption characteristics of 3D printed polymer lattices and their hybrid sandwich structures10.1007/s11665-021-06242-w ↗
10. Experimental investigation of the quasi-static and dynamic compressive behavior of polymer-based 3D-printed lattice structures10.1016/j.ijimpeng.2023.104640 ↗
11. A computational approach in understanding the low-velocity impact behavior and damage of 3D-printed polymer lattice structures10.1007/s11665-021-05873-3 ↗
12. Low-velocity impact response of 3D-printed lattice structure with foam reinforcement10.1016/j.compstruct.2018.02.042 ↗
13. Energy absorption and self-sensing performance of 3D printed CF/PEEK cellular composites10.1016/j.matdes.2021.109863 ↗
14. N. Khan, A. Riccio, A systematic review of design for additive manufacturing of aerospace lattice structures: current trends and future directions. Prog. Aerosp. Sci., 2024. 149.10.1016/j.paerosci.2024.101021 ↗
15. 3D printed octet plate-lattices for tunable energy absorption10.1016/j.matdes.2023.111835 ↗
16. Fused filament fabricated strut-based uniform and density gradient gyroid structures: an experimental investigation of mechanical properties and energy absorption capabilities
17. Energy-absorbing porous materials: bioinspired architecture and fabrication10.1007/s12274-023-6223-8 ↗
18. Impact performance of 3D printed spatially varying elastomeric lattices10.3390/polym15051178 ↗
19. Impact of filler composition on mechanical and dynamic response of 3-D printed silicone-based nanocomposite elastomers10.1016/j.compscitech.2020.108258 ↗
20. 3D-auxetic elastomeric cellular structures for impact protection
21. Influence of structural arrangements on static and dynamic properties of additively manufactured polyester elastomer lattice metamaterials
22. Liquid‐crystal‐elastomer‐based dissipative structures by digital light processing 3D printing10.1002/adma.202000797 ↗
23. On the effect of strain rate during the cyclic compressive loading of liquid crystal elastomers and their 3D printed lattices10.1016/j.mechmat.2024.105086 ↗
24. The impact attenuation behavior of three-dimensional soft elastomeric lattices10.1016/j.taml.2025.100579 ↗
25. Mechanically robust 3D printed elastomeric lattices inspired by strong and tough hierarchical structures
26. Objective optimization and two-way design of double-layer cushion structure enhanced force stability
27. Vertical stiffness of functionally graded hexagonal honeycomb structures for non-pneumatic tyres produced by fused filament fabrication
28. Effect of fused filament fabrication process parameters on compressive strength of thermoplastic polyurethane and polylactic acid lattice structures10.1007/s11665-022-06664-0 ↗
29. Compression and resilient behavior of graded triply periodic minimal surface structures with soft materials fabricated by fused filament fabrication10.1016/j.jmapro.2023.09.034 ↗
30. On the relation between indentation hardness and Young's modulus10.5254/1.3542351 ↗
31. Buckling elastomeric springs and lattices for tailored energy absorption
32. Additive manufacturing of thermoplastic elastomer structures using dual material core-shell filaments
33. The coupled strength and toughness of interconnected and interpenetrating multi-material gyroids10.1557/s43577-021-00249-3 ↗
34. Toughening by interpenetrating lattices10.1016/j.matt.2022.11.025 ↗
35. Design and fabrication of architected multi-material lattices with tunable stiffness, strength, and energy absorption10.1016/j.matdes.2022.110613 ↗
36. Rapid manufacturing of micro-drilling devices using FFF-type 3D printing technology10.1038/s41598-021-91149-8 ↗
37. Application of fused filament fabrication 3D printing and molding to produce flexible, scaled neuron morphology models10.1108/RPJ-10-2023-0378 ↗
38. Combining 3D printing and injection moulding for the fabrication of polymer micro-components with internal hollow features10.1007/s40964-024-00616-x ↗
39. The utilization of polyvinyl alcohol (PVA) filaments for the three-dimensional printing of water-soluble patterns for investment casting
40. Characterisation and modeling of additively-manufactured polymeric hybrid lattice structures for energy absorption10.1016/j.ijmecsci.2020.106101 ↗
41. Energy absorption properties of 3D-printed polymeric gyroid structures for an aircraft wing leading edge10.3390/aerospace11100801 ↗
42. Energy absorption characteristics of additively manufactured plate-lattices under low- velocity impact loading10.1016/j.ijimpeng.2020.103768 ↗
43. Buckling elastomeric springs and lattices for tailored energy absorption
44. Mechanical response of 3-dimensional tensegrity lattices10.1016/j.compositesb.2016.10.046 ↗
45. Neither fluorocarbons nor silicones: hydrocarbon-based water-borne healable supramolecular elastomer with unprecedent dual resistance to water and organic solvents10.31635/ccschem.022.202201775 ↗
46. An additive manufacturing test artifact10.6028/jres.119.017 ↗
47. Silicone mold accuracy in polyurethane vacuum casting10.1002/masy.202000242 ↗
48. Recent progress on polymer materials for additive manufacturing10.1002/adfm.202003062 ↗
49. Fit, stability and comfort assessment of custom-fitted bicycle helmet inner liner designs, based on 3D anthropometric data10.1016/j.apergo.2017.12.002 ↗