journal article·2020-04Open access

Rotational outward solidification casting: An innovative single step process to produce a functionally graded aluminum reinforced with quasicrystal approximant phases

Tales Ferreira, Ivanir Luiz de Oliveira, Guilherme Zepon, Claudemiro Bolfarini

Materials & Design· Volume 189

Abstract

A secondary AlSi7.5Cu3-(Fe,Mn) alloy with small additions of Mn and Fe was processed by an innovative rotational outward solidification casting process to produce a functionally graded aluminum (FGA). A cylinder was produced in a single step presenting two well-defined metallurgically bonded layers (A and B) with distinct chemical composition, structure and mechanical properties. Both layers were deeply characterized through different techniques. Layer A microstructure has more than 50%vol. of the primary α-Al12(Fe,Mn,Cr)3Si quasicrystal approximant phase embedded in an Al-FCC matrix. On the other hand, layer B presents the typical hypoeutectic microstructure of the conventional AlSi7.5Cu3 alloy. Microhardness of the primary α-Al12(Fe,Mn,Cr)3Si phase and macro-hardness profile of the FGA were measured. It was found that the hardness of layer A is approximately 1.6 times higher than layer B. This new FGA may be an alternative for producing parts that require gradient properties such as, for instance, automobile engine blocks.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Quasicrystal Structures and Properties · Microstructure and mechanical properties · Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Improved aluminium alloys for common rail diesel cylinder heads
2. Alloy and casting process optimization for engine block application
3. Interplay between residual stresses, microstructure, process variables and engine block casting integrity10.1007/s11661-012-1340-0 ↗
4. Measurement of residual stresses in cast aluminium engine blocks10.1016/j.jmatprotec.2007.01.023 ↗
5. Application of cast Al–Si alloys in internal combustion engine components10.1179/1743280413Y.0000000027 ↗
6. Lenny · 2011
7. Crystal structure of β-Al4.5FeSi10.1107/S0108768193013096 ↗
8. Crystallographic studies on the iron-containing intermetallic phases in the 319-type aluminium casting alloys10.1080/14786430801942970 ↗
9. Nucleation and growth dynamics of the α-Al/β-Al5FeSi eutectic in a complex Al-Si-Cu-Fe alloy
10. Morphology of β-Al5FeSi phase in Al-Si cast alloys10.2320/matertrans.47.1303 ↗
11. Effect of Fe content on the fracture behaviour of Al-Si-Cu cast alloys10.1016/j.matdes.2014.01.037 ↗
12. The role of alloying additives and aging treatment on the impact behavior of 319 cast alloy10.1016/j.matdes.2011.02.047 ↗
13. A study of tensile properties in Al-Si-Cu and Al-Si-Mg alloys: effect of β-iron intermetallics and porosity10.1016/j.msea.2008.01.028 ↗
14. Iron-related porosity in Al-Si-(Cu) foundry alloys10.1016/j.msea.2006.03.045 ↗
15. Influence of Sr and Mn additions on intermetallic compound morphologies in Al-Si-Cu-Fe cast alloys10.2320/matertrans.44.2611 ↗
16. Predicting the formation of intermetallic phases in the Al-Si-Fe system with Mn additions10.1007/s11669-017-0542-y ↗
17. Morphological changes and segregation of β-Al9Fe2Si2 phase: a perspective from better recyclability of cast Al-Si alloys10.1016/j.matdes.2016.06.096 ↗
18. The effect of iron and manganese on the formation of intermetallic compounds in aluminum-silicon alloys10.1016/S0921-5093(04)00832-9 ↗
19. On the formation of sludge intermetallic particles in secondary aluminum alloys10.1007/s11661-015-2942-0 ↗
20. Morphologies and growth mechanisms of α-Al(FeMn)Si in Al-Si-Fe-Mn alloy10.1016/j.matlet.2013.08.039 ↗
21. In-situ study of morphology and growth of primary α-Al(FeMnCr)Si intermetallics in an Al-Si alloy10.1016/j.actamat.2017.03.026 ↗
22. Primary crystals of AlfeMnSi intermetallics in the cast AlSi alloys10.1515/amm-2017-0254 ↗
23. The effects of Fe-particles on the tensile properties of Al-Si-Cu alloys10.3390/met6120314 ↗
24. Microstructures and mechanical properties of squeeze cast Al-5.0Cu-0.6Mn alloys with different Fe content10.1016/j.matdes.2013.05.079 ↗
25. The effects of Mn additions on the microstructure and mechanical properties of Al-Si-Cu casting alloys10.1016/j.msea.2007.12.026 ↗
26. Cr-induced morphology change of primary Mn-rich phase in Al-Si-Cu-Mn heat resistant aluminum alloys and its contribution to high temperature strength10.1016/j.msea.2017.10.049 ↗
27. Effect of Cr content and heat-treatment on the high temperature strength of eutectic Al-Si alloys10.1016/j.jallcom.2015.05.167 ↗
28. Eutectic Al-Si-Cu-Fe-Mn alloys with enhanced mechanical properties at room and elevated temperature10.1016/j.matdes.2011.04.005 ↗
29. The crystal structure of the ternary alloy α(AlFeSi)10.1107/S0365110X67004372 ↗
30. The crystal structure of the ternary alloy α(AlMnSi)10.1107/S0365110X6600149X ↗
31. Approximate icosahedral symmetry of α-Al(Fe,Mn,Cr)Si in electron backscatter diffraction analysis of a secondary Al-Si casting alloy10.1016/j.matchar.2018.05.013 ↗
32. Properties- and applications of quasicrystals and complex metallic alloys10.1039/c2cs35110b ↗
33. Effect of Cr addition on the formation of the decagonal quasicrystalline phase of a rapidly solidified Al-Ni-Co alloy10.1016/j.jallcom.2016.10.050 ↗
34. Kang · 2017
35. Multi-phase quasicrystalline alloys for superior wear resistance10.1016/j.matdes.2016.06.113 ↗
36. Phase and thermal stability analysis of Al-Fe-V-Si-Y alloys after solidification at intermediate cooling rates
37. Enhancement of mechanical properties of aluminum and 2124 aluminum alloy by the addition of quasicrystalline phases10.1590/1980-5373-mr-2016-0088 ↗
38. Structural, mechanical and thermal characterization of an Al-Co-Fe-Cr alloy for wear and thermal barrier coating applications10.1016/j.surfcoat.2017.03.066 ↗
39. Microstructure and mechanical behavior of Al92Fe3Cr2X3 (X = Ce, Mn, Ti, and V) alloys processed by centrifugal force casting
40. Ichikawa · 2001
41. Design and fabrication of functionally graded in-situ aluminium composites for automotive pistons10.1016/j.matdes.2015.09.099 ↗
42. Fabrication of aluminum alloy functionally graded material using directional solidification under an axial static magnetic field
43. Fabrication of Fe-FeAl functionally graded material using the wire-arc additive manufacturing process10.1007/s11663-015-0509-5 ↗
44. Powder metallurgical fabrication and microstructural investigations of aluminum/steel functionally graded material
45. Functionally graded material: an overview
46. Inward and outward solidification of cylindrical castings: the role of the metal/mold heat transfer coefficient10.1016/j.matchemphys.2012.07.024 ↗
47. Thermo-Calc & DICTRA, computational tools for materials science10.1016/S0364-5916(02)00037-8 ↗
48. Astm · 2011 · 1
49. Standard test method for Brinell hardness of metallic materials
50. Precipitation of primary Fe-rich compounds in secondary AlSi9Cu3(Fe) alloys10.1007/s10973-015-4952-y ↗
51. Solidification characteristics of aluminum alloys
52. Crystal and quasicrystal structures in Al-Mn-Si alloys10.1103/PhysRevLett.55.2883 ↗
53. Manganese-induced ordering in the α-(Al-Mn-Fe-Si) approximant phase10.1080/09500839408240993 ↗
54. Effects of Mn on the crystal structure of α-Al(Mn,Fe)Si particles in A356 alloys10.1016/j.jcrysgro.2006.02.006 ↗
55. The disorder-order transformation of C-Al(Mn, Fe)Si phase10.1016/0956-716X(93)90378-6 ↗
56. Study on composition and crystal structure of dispersoids in AlMgSi alloys10.1023/A:1004673321013 ↗
57. Insight into the complex ternary phase behavior in Al-Mn-Ce alloys10.1016/j.jallcom.2017.08.136 ↗
58. Microstructures of Mg-Al-Zn and Al-Si-Cu cast alloys
59. Phases morphology and distribution of the Al-Si-Cu alloy
60. Evolution of phases in a recycled Al-Si cast alloy during solution treatment