Effects of various second phase ratios and contents on microstructure and mechanical properties of eutectic Sn58Bi alloy
Source abstract
Abstract
A distinctive low melting point heterostructure alloy (LMH) Sn-Bi-Cu-Zn-Ag-Sb was prepared by introducing different ratios and contents of second phase into the eutectic Sn58Bi alloy (SBE). Rapid solidification results in a dispersion of Cu5Zn8, Ag3Sn, and SbSn precipitated phases in Sn53Bi3Cu3Zn2Ag2Sb (LMH32). Besides, the nano-sized η'-Cu6Sn5 and Ag3Sn phases were also observed in the alloy matrix. During solidification, the Cu5Zn8 and Ag3Sn phases are used as the heterogeneous nucleation matrix of the Sn and Bi phases, which significantly refines the eutectic structure and leads to fine-grained strengthening. And the formation of Sn(Sb) solid solution phase leads to solid solution strengthening. The significant mechanical incompatibility between the matrix and the second phases of the LMHs produces a higher back stress hardening effect. The coupling effect of multiple strengthening mechanisms causes the ultimate tensile strength (UTS) of LMH32 reaches 102 MPa, higher 88.9% than that of SBE, and the elongation reaches 12.8%, but the melting point does not change significantly.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Composition, microstructure, phase constitution and fundamental physicochemical properties of low-melting point multi-component eutectic alloys10.1016/j.jmst.2016.08.022 ↗
2. Low-temperature solders
3. Low melting point solders based on Sn, Bi, and In elements
4. Thermal and mechanical properties of graphite foam/Wood's alloy composite for thermal energy storage10.1016/j.carbon.2010.01.002 ↗
5. Permeation behavior of low-melting-point Sn–Bi alloy in the fiber channel of pine wood10.1016/j.matdes.2020.109068 ↗
6. Energy storage materials with oxide-encapsulated inclusions of low melting metal10.1016/j.actamat.2016.01.074 ↗
7. Use of hop (Humulus lupulus) agricultural by-products for the reduction of aqueous lead (II) environmental health hazards10.1016/S0304-3894(01)00363-6 ↗
8. The significance of strain weakening and self-annealing in a superplastic Bi-Sn eutectic alloy processed by high-pressure torsion10.1016/j.actamat.2019.11.064 ↗
9. The effect of Ni on the growth morphology of primary β-phase in an In-35 wt% Sn alloy10.1016/j.jallcom.2021.163172 ↗
10. Inhibition of intermetallic compounds growth at Sn–58Bi/Cu interface bearing CuZnAl memory particles (2–6 μm)
11. Effects of Trace Amounts of Rare Earth Additions on Microstructure and Properties of Sn-Bi-based Solder Alloy10.1007/s11664-008-0458-8 ↗
12. Materials modification of the lead-free solders incorporated with micro/nano-sized particles: a review10.1016/j.matdes.2020.109224 ↗
13. Effects of Ni addition on mechanical properties of Sn58Bi solder alloy during solid-state aging10.1016/j.msea.2016.05.015 ↗
14. Effects of Ti addition on the microstructure, mechanical properties and electrical resistivity of eutectic Sn58Bi alloy10.1016/j.msea.2018.12.012 ↗
15. Microstructure, IMCs Layer and Reliability of Sn-58Bi Solder Joint Reinforced by Mo Nanoparticles During Thermal Cycling10.1016/j.matchar.2018.12.012 ↗
16. Elastic modulus, hardness and creep performance of SnBi alloys using nanoindentation10.1016/j.msea.2012.07.120 ↗
17. Effects of endogenous Al and Zn phases on mechanical properties of Sn58Bi eutectic alloy10.1016/j.matchar.2021.111089 ↗
18. Improvements in mechanical properties of Sn-Bi alloys with addition of Zn and In10.1016/j.msea.2021.141131 ↗
19. Long range internal stresses in single-phase crystalline materials10.1016/j.ijplas.2012.10.003 ↗
20. A comparison of two simple methods for measuring cyclic internal and effective stresses10.1016/0025-5416(84)90083-1 ↗
21. On the origin of the tensile flow stress in the stainless steel AISI 316L at 300 k: back stress and effective stress10.1016/S1359-6454(99)00222-0 ↗
22. Modeling the Bauschinger effect for sheet metals, part I: theory10.1016/S0749-6419(01)00046-8 ↗
23. Significant Bauschinger effect and back stress strengthening in an ultrafine grained pure aluminum fabricated by severe plastic deformation process10.1016/j.scriptamat.2022.114503 ↗
24. Back stress strengthening and strain hardening in gradient structure10.1080/21663831.2016.1153004 ↗
25. Origins of back stress strengthening in Fe-22Mn-0.6C(-3Al) TWIP steels10.1016/j.msea.2020.139834 ↗
26. Solid solution induced back-stress in multi-principal element alloys: Experiment and modeling10.1016/j.msea.2022.142621 ↗
27. Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at. % Cu alloy10.1016/j.actamat.2020.04.006 ↗
28. Rapidly quenched metals
29. Revealing the relation between microstructural heterogeneities and local mechanical properties of complex-phase steel by correlative electron microscopy and nanoindentation characterization10.1016/j.matdes.2021.109620 ↗
30. Impact of Precipitated Phases on the Microstructure and Mechanical Properties of Eutectic Sn58Bi Alloy10.1016/j.jallcom.2022.163882 ↗
31. The phase equilibria in the Sb-Sn system-Part I: Literature review10.1016/j.jallcom.2017.08.215 ↗
32. Incommensurate stistaite-order made to order10.1021/ic900496p ↗
33. The phase equilibria in the Sb-Sn system - Part II: Experimental results10.1016/j.jallcom.2017.11.367 ↗
34. Sb-Sn alloy anodes for Li-ion batteries: The ternary system Li-Sb-Sn10.1016/j.jallcom.2020.157381 ↗
35. Okamoto · 1990
36. Antimony: its History, Chemistry, Mineralogy, Geology, Metallurgy, Uses, Preparations, Analysis, Production, and Valuation; with complete Bibliographies for Students, Manufacturers, and Users of Antimony
37. Nucleation Catalysis10.1021/ie50510a031 ↗
38. High strength, epitaxial nanotwinned Ag films10.1016/j.actamat.2010.09.011 ↗
39. Impurity and alloying effects on interfacial reaction layers in Pb-free soldering10.1016/j.mser.2009.12.001 ↗
40. Kinetics of the η–η′ transformation in Cu6Sn510.1016/j.scriptamat.2011.07.058 ↗
41. R.W.G. Wyckoff, Second edition. Interscience Publishers, New York, New York Sample known as white tin Cryst. Struct. 1 (1963) 7-83.
42. From a volatile molecular precursor to twin-free single crystals of bismuth10.1039/C9CC02820J ↗
43. New refinements of the γ brass type structures Cu5Zn8, Cu5Cd8 and Fe3Zn1010.1107/S0567740874004997 ↗
44. The superstructure of domain-twinned η'-Cu6Sn510.1107/S0108768194004052 ↗
45. The crystal structure of two compounds found in dental amalgam: Ag2Hg3 and Ag3Sn Locality: synthetic10.1107/S0567740872002432 ↗
46. Dislocation behavior in fatigue II. Friction stress and back stress as inferred from an analysis of hysteresis loops10.1016/0025-5416(79)90074-0 ↗
47. Twins and grain boundaries-dominated the reverse Bauschinger effect and tension-compression asymmetry10.1016/j.jmrt.2022.02.080 ↗
48. Designing structures with combined gradients of grain size and precipitation in high entropy alloys for simultaneous improvement of strength and ductility10.1016/j.actamat.2022.117847 ↗
49. Quantification of plastic strain of stainless steel and nickel alloy by electron backscatter diffraction10.1016/j.actamat.2005.08.046 ↗
50. Dislocation-type evolution in quasi-statically compressed polycrystalline nickel10.1016/j.actamat.2018.05.022 ↗
51. Investigations of dislocation-type evolution and strain hardening during mechanical twinning in Fe-22Mn-0.6C twinning-induced plasticity steel10.1016/j.actamat.2020.05.062 ↗
52. Mechanism-based strain gradient plasticity I. Theory10.1016/S0022-5096(98)00103-3 ↗
53. Geometrically necessary dislocations and strain gradient plasticity: a few critical issues10.1016/S1359-6462(02)00335-4 ↗
54. On the Burgers Vectors in β-Sn Single Crystals10.1002/pssa.2210320209 ↗
55. The candidacy of shuffle and shear during compound twinning in hexagonal close-packed structures10.1016/j.actamat.2013.09.002 ↗
56. Enhancing creep resistance of SnBi solder alloy with non-reactive nano fillers: A study using nanoindentation10.1016/j.jallcom.2017.09.177 ↗
57. Nanoprecipitates induced dislocation pinning and multiplication strategy for designing high strength, plasticity and conductivity Cu alloys10.1016/j.scriptamat.2021.113741 ↗
58. Strengthening materials by engineering coherent internal boundaries at the nanoscale10.1126/science.1159610 ↗