journal article·2026-09

Preparation of mullite porous ceramics via emulsion-assisted self-assembly method

Qihan Chen, Jingjing Qu, Fei Liu, Jianping Ma, Yike Chen, Shanqun Zhang, Lifu Lin

Publisher page

Abstract

In this study, the emulsion-assisted self-assembly method was adopted to systematically investigate the effect of dispersant KOS110 content on the flow behavior of ceramic slurries, as well as the influences of solid loading and amounts of added polyvinyl alcohol (PVA) and n-octane on the microstructure and mechanical properties of mullite porous ceramics. Experimental results showed that the dispersant content significantly affected the viscosity characteristics of the slurry when the dispersant content increased to 2 wt%, the slurry viscosity decreased sharply and then stabilized. Increasing the solid loading from 40 vol% to 60 vol% led to a decrease in the porosity from 78.40% to 67.11%, whereas the compressive strength significantly increased from 23.33 MPa to 57.03 MPa. Microstructural analysis indicated that high solid loading promoted the enlargement of pore size and the reduction of interconnected pores, thereby strengthening the ceramic skeleton. An increase in the added PVA content from 0 to 5 wt% resulted in an increase in the porosity from 63.54% to 71.73% and a decrease in the compressive strength from 59.79 MPa to 31.59 MPa as an emulsion stabilizer, PVA induced the formation of more fine and interconnected pores. When the added n-octane content increased from 50 vol% to 80 vol%, the porosity increased significantly from 41.76% to 77.36%, whereas the compressive strength decreased from 118.84 MPa to 26.52 MPa, which was microscopically characterized by enlarged pore size and thinned pore walls. In the thermal insulation performance test, although the high-porosity samples exhibited a faster initial heating rate, they demonstrated excellent thermal insulation performance owing lower equilibrium temperature and thermal conductivity (with a minimum of 0.115 W/(m·K)). This study clarifies how process parameters regulate the microstructure and properties of mullite porous ceramics, providing a theoretical basis for optimizing their mechanical strength and thermal insulation via microstructural design.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Recycling and utilization of industrial and municipal waste in materials production · Aerogels and thermal insulation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Processing and properties of advanced porous ceramics: an application based review10.1016/j.ceramint.2014.06.095 ↗
2. Controllable preparation and multifunctional application of high-strength porous anorthite ceramics
3. Anisotropic porous ceramic material with hierarchical architecture for thermal insulation
4. Near-zero sintering shrinkage porous mullite ceramics with high porosity and low thermal conductivity10.1016/j.ceramint.2024.05.270 ↗
5. Open-cell mullite ceramic foams derived from porous geopolymer precursors with tailored porosity10.26599/JAC.2023.9220682 ↗
6. Mullite porous ceramics with high strength for high-temperature thermal insulation10.1016/j.jmrt.2023.10.288 ↗
7. Structure and properties of mullite—a review10.1016/j.jeurceramsoc.2007.03.017 ↗
8. Fibrous porous mullite ceramics modified by mullite whiskers for thermal insulation and sound absorption10.1016/j.jeurceramsoc.2022.10.025 ↗
9. Mullite-fibers-reinforced bagasse cellulose aerogels with excellent mechanical, flame retardant, and thermal insulation properties10.3390/ma17153737 ↗
10. Porous fibrous ZrO2-mullite ceramics prepared via tert-butyl alcohol-based gel-casting10.1016/j.ceramint.2018.04.192 ↗
11. Controllable preparation and properties of gel-casting porous mullite ceramics via lignin fiber assisted pore formation method10.1016/j.ceramint.2023.08.234 ↗
12. High gas permeability and directional channels of mullite porous ceramics prepared by pectin-based freeze-drying method10.1111/ijac.14446 ↗
13. A new mullite foamed ceramic prepared by direct-foaming methods in parallel with a mechanical activation technique10.1016/j.ceramint.2022.04.053 ↗
14. Preparation and characterization of eco-friendly and low-cost mullite-corundum foamed ceramics with low thermal conductivity10.1016/j.ceramint.2019.04.003 ↗
15. Processing, microstructure and elastic properties of mullite-based ceramic foams prepared by direct foaming with wheat flour10.1016/j.jeurceramsoc.2015.09.028 ↗
16. A novel way to fabricate fibrous mullite ceramic using sol-gel vacuum impregnation10.1016/j.ceramint.2018.04.066 ↗
17. Multi-functional mullite fiber-based porous ceramics with a multilevel pore structure assembled by alumina platelets and mullite whiskers10.1016/j.ceramint.2022.09.057 ↗
18. A comparative study on the synthesis mechanism and microstructural development of hierarchical porous mullite monoliths obtained by the sol–gel process with three different silicon sources10.1016/j.ceramint.2015.11.166 ↗
19. Complex mullite structures fabricated via digital light processing of a preceramic polysiloxane with active alumina fillers10.1016/j.jeurceramsoc.2018.11.038 ↗
20. Effect of the different additives on the fabrication of porous kaolin-based mullite ceramics10.1016/j.ceramint.2016.08.020 ↗
21. Achieving high strength and low thermal conductivity: additive manufacturing of mullite lightweight refractory10.1016/j.ceramint.2024.05.084 ↗
22. High-strength thermal insulating mullite nanofibrous porous ceramics10.1016/j.jeurceramsoc.2020.01.011 ↗
23. Effect of mullite phase formed in situ on pore structure and properties of high-purity mullite fibrous ceramics10.1016/j.ceramint.2021.10.136 ↗
24. Porous mullite ceramics with low thermal conductivity prepared by foaming and starch consolidation10.1007/s10934-013-9741-z ↗
25. Fabrication of mullite-corundum foamed ceramics for thermal insulation and effect of micro-pore-foaming agent on their properties10.1016/j.jallcom.2019.01.212 ↗
26. Novel mullite ceramic foams with high porosity and strength using only fly ash hollow spheres as raw material10.1016/j.jeurceramsoc.2017.11.002 ↗
27. Fabrication and characterization of porous mullite ceramics with ultra-low shrinkage and high porosity via sol-gel and solid state reaction methods10.1016/j.ceramint.2021.04.020 ↗
28. Tailoring microstructure and properties of porous mullite-based ceramics via sol-gel impregnation10.1016/j.ceramint.2024.06.019 ↗
29. 3D printing of porous low-temperature in-situ mullite ceramic using waste rice husk ash-derived silica10.1016/j.jeurceramsoc.2022.01.001 ↗
30. Vat photopolymerization 3D printing of thermal insulating mullite fiber-based porous ceramics
31. Preparation of lightweight corundum-mullite thermal insulation materials by microwave sintering10.2298/PAC2102170S ↗
32. A novel method based on ultrastable foam and improved gelcasting for fabricating porous mullite ceramics with thermal insulation-mechanical property trade-off10.1007/s10934-015-0091-x ↗
33. Robust, thermally insulating, and high-temperature resistant phosphate-enhanced mullite fiber porous ceramic composites10.1016/j.ceramint.2024.04.097 ↗
34. Microstructure and properties of lightweight fibrous porous mullite ceramics prepared by vacuum squeeze moulding technique10.1016/j.ceramint.2016.06.118 ↗
35. Effect of AlN powders on the debinding and sintering behavior, and thermal conductivity of injection molded AlN ceramics10.1016/j.ceramint.2019.08.183 ↗
36. Characterization of a ceramic powder surface by contact angle measurements and Infrared spectroscopy10.4028/www.scientific.net/KEM.507.233 ↗
37. A novel hybrid deep learning algorithm for estimating temperature-dependent thermal conductivity in transient heat conduction problems10.1016/j.icheatmasstransfer.2025.108871 ↗
38. Effect of air volume fraction on the thermal conductivity of compacted bentonite materials10.1016/j.enggeo.2021.106045 ↗