Tool traverse speed-mediated microstructure and texture engineering for enhanced strength-ductility-corrosion resistance synergy in ZK60 magnesium alloy
Source abstract
Abstract
A strain-rate-controlled microstructural design strategy is proposed to enhance strength-ductility-corrosion resistance synergy in extruded ZK60 magnesium alloy via friction stir processing (FSP). By systematically varying the tool traverse speed (TTS: 100-200 mm/min), the interplay between strain rate and heat input was tailored to regulate dynamic recrystallization (DRX), crystallographic texture, and precipitate stability. FSP induced significant lattice rotation, resulting in orientation transition from prismatic/pyramidal to basal- dominated, which facilitated extensive grain fragmentation, leading to grain refinement from ~15 μm in the extruded state to <8 μm after processing. Increasing TTS increased the strain rate while reducing heat input, resulting in fine DRX grains, weak basal texture, and enhanced Σ13a coincident site lattice (CSL) boundaries. Concurrently, MgZn2 precipitates underwent fragmentation and partial dissolution. Deformation transitioned from slip-dominated parabolic flow in the extruded condition to sigmoidal flow in FSPed samples, governed by {101 ̅2}〈101 ̅1〉 extension twins (ET) activation. The yield strength decreased at 100 mm/min due to early ET activation under relatively coarser grains and stronger basal texture, but recovered at higher TTS through grain refinement. Ultimate tensile strength increased post-FSP due to ET-induced geometric hardening. Notably, the sample processed at 200 mm/min achieved an excellent strength-ductility synergy, due to combination of refined grains and weakened texture. The refined microstructure, increased Σ13a CSL boundaries, and precipitate dissolution collectively suppressed micro-galvanic coupling and promoted uniform surface degradation. As a result, the corrosion current density decreased by more than an order of magnitude compared to the extruded condition, with the lowest observed at 200 mm/min.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (83)
Show source-provided references
1. Development and application of magnesium alloy parts for automotive OEMs: a review10.1016/j.jma.2022.12.015 ↗
2. Preface to the viewpoint set on: the current state of magnesium alloy science and technology10.1016/j.scriptamat.2010.06.029 ↗
3. Biodegradable Mg alloys for orthopedic implants – a review10.1016/j.jma.2021.06.024 ↗
4. Recent developments in high-pressure die-cast magnesium alloys for automotive and future applications10.1016/j.jma.2022.10.001 ↗
5. Mihriban · 2013
6. Room-temperature equal channel angular extrusion of pure magnesium10.1016/j.actamat.2010.01.051 ↗
7. The role of deformation twinning in the fracture behavior and mechanism of basal textured magnesium alloys10.1016/j.msea.2014.02.010 ↗
8. Strain hardening, twinning and texture evolution in magnesium alloy using the all twin variant polycrystal modelling approach10.1016/j.ijplas.2020.102660 ↗
9. Dynamic recrystallization and its effect on microstructure and texture evolution in magnesium alloys10.1016/B978-0-12-815732-9.00016-4 ↗
10. Hot workability analysis of AZ61 Mg alloys with processing maps10.1016/j.msea.2014.04.017 ↗
11. Improving the mechanical properties of pure magnesium by three-roll planetary milling10.1016/j.msea.2014.06.061 ↗
12. Enhancing plastic deformability of Mg and its alloys-A review of traditional and nascent developments10.1016/j.jma.2017.11.001 ↗
13. Ductility enhancement in Mg-0.2%Ce alloys10.1016/j.actamat.2018.09.023 ↗
14. Microstructure, deformation, and property of wrought magnesium alloys10.1007/s11661-020-05974-z ↗
15. Investigation on the alloy phases in As-Aged ZK60 magnesium alloy10.4028/www.scientific.net/MSF.488-489.181 ↗
16. Effect of heat treatment on microstructure and mechanical properties of twin roll cast and sequential warm rolled ZK60 alloy sheets10.1016/j.jallcom.2008.08.077 ↗
17. Microstructure and corrosion of cast magnesium alloy ZK60 in NaCl solution10.3390/ma13173833 ↗
18. Superior ductility and strength enhancement of ZK60 magnesium sheets processed by a combination of repeated upsetting and forward extrusion10.1016/j.msea.2016.07.025 ↗
19. Invitro degradation behavior and cytocompatibility of Mg-Zn-Zr alloys10.1007/s10856-010-4111-8 ↗
20. Effect of heat treatment and deformation temperature on the mechanical properties of ECAP processed ZK60 magnesium alloy10.1016/j.msea.2016.09.037 ↗
21. ZK60 based alloys with high-strength and high-ductility: a review
22. Extreme grain refinement by severe plastic deformation: a wealth of challenging science10.1016/j.actamat.2012.10.038 ↗
23. Review: modes and processes of severe plastic deformation (SPD)10.3390/ma11071175 ↗
24. Evolution of sub-micron grain size and weak texture in magnesium alloy Mg–3Al–0.4Mn by a modified multi-axial forging process10.1016/j.scriptamat.2011.10.008 ↗
25. Influence of grain size on the compressive deformation of wrought Mg–3Al–1Zn10.1016/j.actamat.2004.07.015 ↗
26. On the possibility to reduce ECAP deformation temperature in magnesium: deformation behaviour, dynamic recrystallization and mechanical properties10.1016/j.msea.2021.141103 ↗
27. Effect of ECAP strain path on deformation behaviour, microstructure, texture evolution, and mechanical properties in magnesium10.1016/j.msea.2024.147077 ↗
28. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
29. Enhancing grain refinement and corrosion behavior in AZ31B magnesium alloy via stationary shoulder friction stir processing10.1016/j.jmrt.2022.02.059 ↗
30. Friction stir welding/processing of metals and alloys: a comprehensive review on microstructural evolution10.1016/j.pmatsci.2020.100752 ↗
31. The influence of reinforcement particles friction stir processing on microstructure, mechanical properties, tribological and corrosion behaviors: a review10.1016/j.jmrt.2022.07.172 ↗
32. Enhanced mechanical properties of Mg–Al–Zn cast alloy via friction stir processing10.1016/j.scriptamat.2006.10.035 ↗
33. Surface metal-matrix composites based on AZ91 magnesium alloy via friction stir processing: a review10.1007/s12613-022-2589-y ↗
34. Effect of friction stir processing parameters on the microstructure and properties of ZK60 magnesium alloy10.1088/2053-1591/ac475e ↗
35. Relationship between grain size and Zener–Holloman parameter during friction stir processing in AZ31 Mg alloys10.1016/j.scriptamat.2004.05.043 ↗
36. The effect of friction stir processing (FSP) on the microstructure and properties of the AM60 magnesium alloy10.1515/amm-2016-0254 ↗
37. Enhanced mechanical properties of Mg–Gd–Y–Zr casting via friction stir processing10.1016/j.jallcom.2010.11.147 ↗
38. Influence of process parameters on microstructure and mechanical properties of friction-stir-processed Mg-Gd-Y-Zr casting10.1007/s11661-011-1076-2 ↗
39. Producing nanograined microstructure in Mg–Al–Zn alloy by two-step friction stir processing10.1016/j.scriptamat.2008.04.003 ↗
40. Enhancing the high-cycle fatigue strength of Mg–9Al–1Zn casting by friction stir processing10.1016/j.scriptamat.2009.05.023 ↗
41. Corrosion behavior of a friction stir processed rare-earth added magnesium alloy10.1016/j.corsci.2012.01.007 ↗
42. Influence of bimodal grain size distribution on the corrosion behavior of friction stir processed biodegradable AZ31 magnesium alloy10.1016/j.jma.2015.12.004 ↗
43. Corrosion of an extruded magnesium alloy ZK60 component—The role of microstructural features10.1016/j.jallcom.2011.01.116 ↗
44. Effect of grain refinement and crystallographic texture produced by friction stir processing on the biodegradation behavior of a Mg-Nd-Zn alloy10.1016/j.jmst.2018.11.025 ↗
45. Microstructure, tensile properties and corrosion behavior of friction stir processed Mg-9Li-1Zn alloy10.1016/j.jmatprotec.2018.12.026 ↗
46. Enhancing corrosion resistance and mechanical properties of AZ31 magnesium alloy by friction stir processing with the same speed ratio10.1016/j.jallcom.2020.154452 ↗
47. Enhancing mechanical properties of AZ61 magnesium alloy via friction stir processing: effect of processing parameters10.1016/j.msea.2020.139945 ↗
48. Effect of grain refinement on corrosion rate, mechanical and machining behavior of friction stir processed ZE41 Mg alloy10.1007/s12666-018-1467-9 ↗
49. The corrosion behavior of Mg-9Al-xRE magnesium alloys modified by friction stir processing10.1016/j.jallcom.2020.156835 ↗
50. Improved corrosion resistance achieved in a friction stir processed Mg-5Zn-0.3Ca alloy with fragmented precipitates10.1016/j.corsci.2022.110675 ↗
51. Simultaneous enhancement of mechanical properties and corrosion resistance of as-cast Mg-5Zn via microstructural modification by friction stir processing10.1016/j.jma.2021.08.029 ↗
52. Influence of texture on superplastic behavior of friction stir processed ZK60 magnesium alloy10.1016/j.msea.2012.07.046 ↗
53. 2016 · 1
54. How useful is SBF in predicting in vivo bone bioactivity?10.1016/j.biomaterials.2006.01.017 ↗
55. A review of strain analysis using electron backscatter diffraction10.1017/S1431927611000055 ↗
56. Microstructure-sensitive investigation of magnesium alloy fatigue10.1016/j.ijplas.2014.10.010 ↗
57. Study on corrosion electrochemical behavior of several different coating systems by EIS10.1016/j.porgcoat.2008.08.012 ↗
58. Effect of atomic layer plasma treatment on TALD-ZrO2 film to improve the corrosion protection of Mg–Ca alloy10.1016/j.surfcoat.2021.127811 ↗
59. Corrosion resistance of dicalcium phosphate dihydrate/poly (lactic-co-glycolic acid) hybrid coating on AZ31 magnesium alloy10.1016/j.corsci.2015.10.010 ↗
60. Atomic layer deposited thin films for corrosion protection
61. CPE analysis by local electrochemical impedance spectroscopy10.1016/j.electacta.2005.02.128 ↗
62. A model of grain fragmentation based on lattice curvature10.1016/j.actamat.2009.11.020 ↗
63. Humphreys · 2004
64. 2017
65. Relating grain size to the Zener–Hollomon parameter for twin-roll-cast AZ31B alloy refined by friction stir processing10.1016/j.jmatprotec.2015.02.037 ↗
66. Effect of strain rate on deformation mechanisms of a Mg alloy10.1007/s11661-025-07739-y ↗
67. High strain rate deformation mechanism of extruded WE43 magnesium alloy at room temperature and 400 °C10.1016/j.jallcom.2025.180692 ↗
68. Anisotropic compressive deformation behavior of hot-rolled Mg-3Al-0.5Ce alloy10.1016/j.jma.2024.11.015 ↗
69. Role of slip and twinning on strain hardening, and correlation with geometric hardening, latent hardening, and grain boundary strengthening in Titanium10.1016/j.ijplas.2023.103516 ↗
70. Enhanced mechanical properties and corrosion resistance of a fine-grained Mg-9Al-1Zn alloy: the role of bimodal grain structure and β-Mg17Al12 precipitates10.1016/j.mtla.2020.100840 ↗
71. Corrosion behavior of biomedical AZ91 magnesium alloy in simulated body fluids10.1557/jmr.2007.0233 ↗
72. Effect of pH on Mg(OH)2 film evolution on corroding Mg by in situ kinetic Raman mapping (KRM)10.1016/j.corsci.2019.03.024 ↗
73. Corrosion behavior of fine-grained AZ31B magnesium alloy10.1016/j.corsci.2012.04.039 ↗
74. Grain refinement of magnesium alloys10.1007/s11661-005-0030-6 ↗
75. Grain refining mechanisms in magnesium alloys—An overview10.1007/s12666-009-0088-8 ↗
76. Grain refined and basal textured surface produced by burnishing for improved corrosion performance of AZ31B Mg alloy10.1016/j.corsci.2011.12.018 ↗
77. Corrosion of pure Mg as a function of grain size and processing route10.1002/adem.200800046 ↗
78. Effects of grain refinement on the biocorrosion and in vitro bioactivity of magnesium10.1016/j.msec.2015.07.033 ↗
79. Effect of grain refinement on the dynamic, mechanical properties, and corrosion behaviour of Al-Mg alloy10.3390/met11111825 ↗
80. Effect of grain refinement on mechanical and corrosion behavior of AZ91 magnesium alloy processed by ECAE10.1088/1757-899X/591/1/012015 ↗
81. Roles of inclusion, texture and grain boundary in corrosion resistance of low-nickel austenite stainless steel containing Ce10.2355/isijinternational.ISIJINT-2019-248 ↗
82. The structure of high-angle grain boundaries10.1016/0001-6160(66)90168-4 ↗
83. Characteristics of coincident site lattice grain boundaries developed during equal channel angular pressing of magnesium single crystals10.1016/j.scriptamat.2010.11.011 ↗