journal article·2025-11Open access

Microstructural evolutions and diffusion phenomena during the elaboration of new duplex composite stainless steels by hot isostatic pressing

R. Mvodo Eba, M.R. Ardigo-Besnard, J.-P. Chateau-Cornu, F. Herbst, N. Geoffroy, S. Cazottes, P. Steyer

Abstract

In the present study, hot isostatic pressing (HIP) was used to elaborate a duplex stainless steel (DSS) from a blend of an austenitic 316L and a ferritic 410L powder with equal mass fractions. This blend was selected as it showed the best compromise between ductility and mechanical strength. Microstructural and diffusion phenomena were investigated by interrupted HIP tests performed at temperatures ranging from 800 to 1200 °C. In addition, the influence of the sintering time was studied through a comparison with the same DSS obtained by spark plasma sintering (SPS). The results showed that the HIPed sample microstructure consists of equiaxed grains of austenite and ferrite. Martensite formed inside the ferritic matrix and at the austenite/ferrite interfaces. A prolonged sintering time at high temperature during HIP (4 hours compared to 15 minutes during SPS) led to grain growth and a broadening of the austenite destabilization region on the Schaeffler diagram, from 2.7 ± 0.3 μm after SPS to 12 ± 0.4 μm after HIP. The width of the martensitic region and the martensite fraction increased by approximately 96% and 80%, respectively, after HIP compared to SPS, due to enhanced diffusion phenomena. The coarsening of metastable austenite grains in the HIPed sample lowered the barrier energy required to initiate the austenite-to-martensite transformation and promoted the formation of numerous martensite nucleation sites. Accordingly, despite grain growth, the hardness of the HIPed blend improved by about 17% compared to the SPS sample. Elemental diffusion between 316L and 410L particles did not occur at 800 and 900 °C. Martensite formation started at 900 °C. At 900 and 1000 °C, σ-phase precipitation occurred in the austenite and dissolved from 1100 °C upwards. Despite the extended diffusion time and distance, the initial powder particles remain observable in the microstructure of the HIPed blend, reinforcing the composite nature of this type of DSS, as previously observed after SPS.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Duplex stainless steels-alloys for the 21st century10.3390/met11050836 ↗
2. Super duplex stainless steels10.1179/mst.1992.8.8.685 ↗
3. Duplex stainless steels - a review after DSS ‘07 held in grado10.1002/srin.200806153 ↗
4. Duplex stainless steels-an overview
5. Phase transformation in duplex stainless steels after isothermal treatments, continuous cooling and cold working10.4028/www.scientific.net/MSF.638-642.2986 ↗
6. Powder metallurgical duplex austenitic-ferritic stainless steels from prealloyed and mixed powders, powder
7. Sintering transformations in mixtures of austenitic and ferritic stainless steel powders, powder
8. Development of duplex stainless steels by field-assisted hot pressing: influence of the particle size and morphology of the powders on the final mechanical properties10.1007/s11661-017-4385-2 ↗
9. Phase transformation mechanisms occurring during spark plasma sintering elaboration of new duplex composite stainless steels10.1016/j.matchemphys.2024.129796 ↗
10. Duplex and graded austenitic-to-martensitic steels by powder metallurgy: interface diffusion and strength composite effect10.1016/j.msea.2023.145405 ↗
11. Analysis of the interface and mechanical properties of field-assisted sintered duplex stainless steels10.1016/j.msea.2018.10.111 ↗
12. Characterisation of ferritic to austenitic steel functional grading via powder hot isostatic pressing
13. Fundamental aspects of functional grading via powder hot isostatic pressing - development of microstructure and diffusional processes10.1016/j.matdes.2022.110437 ↗
14. Microstructures and mechanical properties of cold-rolled 21Cr lean duplex stainless steel with medium to high cold rolling reductions10.1016/j.mtcomm.2022.104860 ↗
15. Effect of microstructure tailoring on the deformation coordination of welded duplex stainless steel10.1016/j.matchar.2022.112555 ↗
16. Phase analysis in duplex stainless steel: comparison of EBSD and quantitative metallography methods10.1088/1757-899X/55/1/012010 ↗
17. Agglomerate and particle size effects on sintering yttria-stabilized zirconia10.1111/j.1151-2916.1981.tb09552.x ↗
18. Callister · 2018
19. Ferritic stainless steels: metallurgy, application and weldability
20. Comparison of microstructure and mechanical properties of 316L austenitic steel processed by selective laser melting with hot-isostatic pressed and cast material10.1016/j.msea.2016.10.012 ↗
21. Martensite transformation kinetics in 9Cr–1.7W–0.4Mo–Co ferritic steel10.1016/j.jallcom.2014.05.060 ↗
22. A review of the thermal stability of metastable austenite in steels: martensite formation10.1016/j.jmst.2021.03.020 ↗
23. Isothermal decomposition of austenite in presence of martensite in advanced high strength steels: a review
24. On the effect of fine grain size on the Ms temperature in Fe-27Ni-0.025C alloys10.1007/BF02645565 ↗
25. Overview 15 the microstructure and kinetics of martensite transformations in splat-quenched Fe and Fe-Ni alloys-I10.1016/0001-6160(82)90213-9 ↗
26. Davis · 1994
27. Abe · 2008
28. Diffusion bonds in iron and a low-alloy steel10.1007/BF00549798 ↗
29. Characterization of the formation of nickel-rich areas in PM steels and their effect on mechanical properties
30. Microstructural characterization of nickel rich areas and their influence on endurance limit of sintered steel, powder
31. Overview of intermetallic sigma (σ) phase precipitation in stainless steels
32. Precipitation in AISI 316L(N) during creep tests at 550 and 600°C up to 10 years10.1016/j.jnucmat.2006.12.027 ↗
33. Comparative study on sigma phase precipitation of three types of stainless steels: austenitic, superferritic and duplex10.1179/174328406X109230 ↗
34. Padilha · 2006
35. Vander Voort
36. Precipitation in creep resistant austenitic stainless steels10.1179/026708301101508972 ↗
37. Phase instabilities during high temperature exposure of 316 austenitic stainless steel10.1007/BF02647659 ↗
38. Laser metal deposition of low carbon 410L stainless steel and heat treatment10.1016/j.msea.2023.144987 ↗
39. Kang · 2004
40. Functional properties of a spark plasma sintered ultrafine-grained 316L steel10.1016/j.matdes.2014.06.053 ↗