Influence of bainitic transformation temperature on microstructure evolution during isothermal holding and subsequent cooling
Source abstract
Abstract
Modified mold steels have recently gained attention as a novel approach in steel grades due to their high-performance applications. In this study, high-resolution dilatometry was used to study the isothermal bainitic transformation of a medium-carbon low-alloy steel after full austenitization at 900 °C, followed by austempering for 3 h at temperatures ranging from 380 to 450 °C. The results showed that no bainitic phase transformation occurred at 450 °C, while an incomplete transformation was observed at all lower tested temperatures, and martensitic transformation occurred upon cooling at the final stage. Increasing the austempering temperature from 380 °C to 425 °C resulted in a lower volume fraction of bainite and a higher amount of martensite, whereas at 450 °C, a full lath martensite microstructure formed during final cooling. Electron backscatter diffraction (EBSD) and scanning electron microscopy (SEM) analyses revealed that increasing the isothermal holding temperature led to increased thickness of the bainitic blocks and a higher volume fraction of martensite. Vickers hardness increased from 412 to 500 HV between 380 and 450 °C holding temperatures. This increase was attributed to the phase volume fraction, the carbon content of martensite, and the thickness of bainitic ferrite blocks. Nanoindentation tests were conducted on different martensitic and bainitic regions to compare the influence of isothermal holding temperature on the characteristics of the phases. The results indicated that as the isothermal temperature increased, the carbon content of martensite decreased, leading to a reduction in the nanohardness of the martensitic regions from 8.3 GPa at 400 °C to 7.8 GPa at 425 °C and 6.9 GPa at 450 °C. Furthermore, the average block thickness of bainitic ferrite increased from 0.71 μm to 1.98 μm as the isothermal temperature was raised from 380 °C to 425 °C, resulting in a decrease in nanohardness from 6.3 to 5.4 GPa. These findings are interpreted in terms of the evolution of bainitic block thickness and the carbon content of martensite at different austempering temperatures, as well as their impact on the hardness of the phases.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. Improved uniformity of hardness by continuous low temperature bainitic transformation in prehardened mold steel with large section10.1016/j.msea.2017.08.104 ↗
2. Microstructure evolution and mechanical properties in 718H pre-hardened mold steel during tempering10.1016/j.msea.2017.10.047 ↗
3. Microstructure of ultrafine acicular bainite and mechanical properties of 3Cr2MnNiMo mold steel during austempering10.1002/srin.202200151 ↗
4. The effect of stress on bainite transformation, microstructure, and properties of a low-carbon bainitic steel10.1002/srin.201900159 ↗
5. Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel10.1016/j.matchemphys.2024.129765 ↗
6. Effect of carbon distribution range in mixed bainite/martensite/retained austenite microstructure on mechanical properties10.1016/j.jmrt.2021.12.121 ↗
7. Austenite grain growth and effect of austenite grain size on bainitic transformation10.1080/02670836.2022.2045547 ↗
8. Effect of ultra-fine martensite and retained austenite induced by slow quenching on the mechanical properties of 9Cr 1.5Mo1Co(FB2) steel10.1016/j.matchar.2021.111452 ↗
9. Acicular ferrite formation during isothermal holding in HSLA steel10.1007/s10853-015-9675-8 ↗
10. Bhadeshia · 2001
11. Pereloma · 2012 · vol. 2
12. Effects of austempering temperature on bainitic microstructure and mechanical properties of a high-C high-Si steel10.1016/j.msea.2018.11.004 ↗
13. Bainite: an atom-probe study of the incomplete reaction phenomenon10.1016/0001-6160(82)90075-X ↗
14. On measurement of carbon content in retained austenite in a nanostructured bainitic steel10.1007/s10853-011-5880-2 ↗
15. Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel10.1007/s43452-023-00735-2 ↗
16. Effect of austempering temperature on microstructure and mechanical properties of M50 bearing steel10.1016/j.jmrt.2022.09.002 ↗
17. Bainite in steels10.1007/BF02656561 ↗
18. Refined bainite microstructure and mechanical properties of a high-strength low-carbon bainitic steel treated by austempering below and above MS10.1002/srin.201700469 ↗
19. Accelerated isothermal phase transformation and enhanced mechanical properties of railway wheel steel: the significant role of pre-existing bainite10.1002/srin.202100494 ↗
20. Effect of different austempering heat treatments on corrosion properties of high silicon steel10.3390/ma14020288 ↗
21. Effect of isothermal transformation temperature on amount of retained austenite and its thermal stability in a bainitic Fe–3%Si–0.45%C–X steel10.1016/S1359-6462(02)00303-2 ↗
22. Isothermal transformation kinetics, microstructure and mechanical properties of a carbide free bainitic steel10.1016/j.matchar.2021.111166 ↗
23. Effect of ausforming temperature on bainite morphology in a 3.2% Si carbide-free bainitic steel10.1016/j.msea.2022.144553 ↗
24. The bainite transformation in a silicon steel10.1007/BF02658309 ↗
25. Microstructures and mechanical characteristics of a medium carbon super-bainitic steel after isothermal transformation10.1007/s11665-014-1235-x ↗
26. Development of hard bainite10.2355/isijinternational.43.1238 ↗
27. Enhancing strength-ductility combination in a novel Cu–Ni bearing Q&P steel by tailoring the characteristics of fresh martensite10.1016/j.jmrt.2023.05.153 ↗
28. Effect of short-term low-temperature austempering on the microstructure and abrasive wear of medium-carbon low-alloy steel10.1007/s12540-020-00957-6 ↗
29. Effect of austempering time on bainite plate thickness and variant selection in a high carbon low alloy steel10.1016/j.matchar.2023.112923 ↗
30. Isothermal transformation of a commercial super-bainitic steel: part I microstructural characterization and hardness10.1007/s11665-016-2473-x ↗
31. Microstructure and mechanical properties of austempered medium-carbon spring steel10.1007/s12540-018-0085-8 ↗
32. Influence of austempering temperature on the mechanical properties of a low carbon low alloy steel10.1016/j.msea.2011.03.038 ↗
33. On the decomposition of austenite in a high-silicon medium-carbon steel during quenching and isothermal holding above and below the Ms temperature10.1016/j.matchar.2020.110224 ↗
34. Effects of temperature and time of isothermal holding on retained austenite stability in Medium-Mn steels10.3390/app8112156 ↗
35. Effect of isothermal holding temperature on retained austenite fraction in medium-carbon Nb/ti-Microalloyed TRIP steel
36. Study of the isothermal bainitic transformation and austenite stability in an advanced Al-rich medium-Mn steel10.1007/s43452-022-00475-9 ↗
37. Study on carbide-bearing and carbide-free bainitic steels and their wear resistance10.1080/02670836.2016.1242205 ↗
38. Comparative study of the uniaxial cyclic behaviour of carbide-bearing and carbide-free bainitic steels10.3390/met8060422 ↗
39. Study on microstructures and properties of carbide-free and carbide-bearing bainitic steels10.1016/j.msea.2017.12.108 ↗
40. Influence of transformation temperature on the high-cycle fatigue performance of carbide-bearing and carbide-free bainite10.1002/srin.202300238 ↗
41. Dilatometric study of martensitic transformation in NiTiCu and NiTi shape memory alloys10.1023/A:1012908222409 ↗
42. Hurel · 2022 · 60
43. Quantitative phase analysis of martensite-bainite steel using EBSD and its microstructure, tensile and high-cycle fatigue behaviors10.1016/j.msea.2020.139375 ↗
44. Texture analysis with MTEX – free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
45. Committee · 2013 · 7
46. Nanoindentation study of ferrite–martensite dual phase steels developed by a new thermomechanical processing10.1016/j.msea.2015.04.098 ↗
47. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
48. Study on the effect of nanoindentation test method on micromechanical properties of granite minerals
49. Carbide-free bainite transformations above and below martensite start temperature investigated by In-Situ high-energy X-Ray diffraction
50. Extension of the martensite transformation temperature relation to larger alloying elements and contents10.1002/adem.201300116 ↗
51. Thermodynamic analysis and isothermal bainitic transformation kinetics in lean medium-Mn steels10.1007/s10973-020-10259-z ↗
52. Enhanced strength and toughness of low-carbon bainitic steel by refining prior austenite grains and austempering below Ms10.1002/srin.202100263 ↗
53. EBSD study of martensite in a dual phase steel10.1017/S1431927602106507 ↗
54. Analysis of complex steel microstructures by high-resolution EBSD
55. Detection and estimation of retained austenite in a high strength Si-Bearing bainite-martensite-retained austenite micro-composite steel after quenching and bainitic holding (Q& B)10.3390/met9050492 ↗
56. Characterization of bainitic/martensitic structures formed in isothermal treatments below the Ms temperature10.1016/j.matchar.2017.04.007 ↗
57. An assessment of the contributing factors to the nanoscale structural refinement of advanced bainitic steels10.1016/j.jallcom.2011.11.066 ↗
58. Transferring nanoscale bainite concept to lower C contents: a perspective10.3390/met7050159 ↗
59. Correlation between strength and hardness for substructures of lath martensite in low- and medium-carbon steels10.1016/j.msea.2022.144007 ↗
60. Bainite plate thickness reduction and microstructure tailoring by double austempering of Al-rich 3Mn steel10.1016/j.msea.2022.143743 ↗
61. Microstructure, crystallography and nucleation mechanism of NANOBAIN steel10.1007/s12613-013-0849-6 ↗