Tensile fracture behavior of Ni- and Cr–C/Ni-coated high-carbon tool steel (AISI 1090)
Source abstract
Abstract
Abstract The tensile fracture behavior of Ni- and Cr–C/Ni-coated high-carbon tool steel specimens was studied. The Cr–C coating was prepared in a Cr 3+ -based plating bath, and the Ni coating was prepared in a Ni-sulfate bath. The experimental results indicate that the yield and ultimate tensile strengths were not changed after Ni- or Cr–C/Ni-coating. However, the elongation percentage of the steel specimen was clearly reduced after Cr–C/Ni-coating. According to the fractography study, the fracture feature with necking and a cup-and-cone appearance was observed in the steel and Ni-coated steel specimens after the tensile test. However, the fracture feature of the Cr–C/Ni-coated steel specimens with relatively low elongation percentages exhibited an obvious cracking plateau. Under the application of tensile stress, cracks in the Cr–C coating propagated through the Ni coating and then into the steel substrate, forming a cracking plateau and, decreasing its elongation percentage. Moreover, branch cracking was observed during crack propagation to develop a fracture appearance with some cracks and crack facets.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. Corrosion protection properties of electroless Nickel/PTFE, Phosphate/MoS2 and Bronze/PTFE coatings applied to improve the wear resistance of carbon steel10.1016/S0257-8972(03)00662-5 ↗
2. Improved corrosion behavior of nanocrystalline zinc produced by pulse-current electrodeposition10.1016/S0010-938X(03)00142-2 ↗
3. Improving the corrosion performance of Cr-C amorphous coatings on steel substrate by modifying the steel surface preparation10.1016/j.surfcoat.2010.08.123 ↗
4. Electrodeposition of Ni–RuAl composite coating on steel surface10.1016/j.jallcom.2008.05.050 ↗
5. Investigation on microstructural, anti-corrosion and mechanical properties of doped Zn–Al–SnO2 metal matrix composite coating on mild steel10.1016/j.jallcom.2014.10.013 ↗
6. Effect of cyclic heat treatments on spheroidizing behavior of cementite in high carbon steel10.1016/j.msea.2013.02.059 ↗
7. Effects of tungsten addition and heat treatment conditions on microstructure and mechanical properties of microalloyed forging steels10.1016/j.msea.2012.11.006 ↗
8. Effect of cyclic heat treatment on microstructure and mechanical properties of 0.6 wt% carbon steel10.1016/j.msea.2010.03.003 ↗
9. Tensile fracture behaviour of Cu- and Ni/Cu -coated Mg alloy (AZ61)10.1016/j.msea.2012.07.098 ↗
10. The hardening mechanism of a chromium -carbon deposit electroplated from a trivalent chromium-based bath10.1016/j.tsf.2009.03.188 ↗
11. Increasing the wear and corrosion resistance of magnesium alloy (AZ91D) with electrodeposition from eco-friendly copper- and trivalent chromium-plating baths10.1016/j.surfcoat.2010.06.012 ↗
12. Characterization of intermediate Cr-C layer fabricated by electrodeposition in hexavalent and trivalent chromium baths10.1016/j.surfcoat.2003.09.069 ↗
13. Characterization of as-deposited and annealed Cr–C alloy coatings produced from a trivalent chromium bath10.1016/j.jallcom.2010.02.101 ↗
14. The effect of formic acid concentration on the conductivity and corrosion resistance of chromium carbide coatings electroplated with trivalent chromium10.1016/j.apsusc.2013.06.008 ↗
15. Kerlins · 1987 · Vol. 12 · pp.12
16. Microstructures and fracture features of cold-rolled low carbon steel sheet after annealing and mechanical stress concurrently loaded10.1016/j.msea.2008.10.006 ↗
17. A comparison of the effects of severe plastic deformation and heat treatment on the tensile properties and impact toughness of aluminum alloy 606110.1016/j.msea.2013.11.067 ↗
18. Strain rate sensitivity and fracture behavior of severely deformed Al–Mn alloy sheets10.1016/j.msea.2011.10.057 ↗
19. The study of electroplating trivalent CrC alloy coatings with different current densities on stainless steel 304 as bipolar plate of proton exchange membrane fuel cells,10.1016/j.tsf.2014.03.034 ↗