journal article·2020-07

Oxidation mechanism of Al-TiO2-MgO-Al2O3 composites after the treatment at 1500 °C in N2-blowing

Yang Sun, Yong Li, Lixin Zhang, Yuan Gao, Jialin Sun

Publisher page

Abstract

Abstract In this paper, metal (Al, Al3Ti), oxides (Spinel, corundum) and non-oxides ((Al2OC)x (AlN)1-x, Ti(C,N)) composite refractories with excellent oxidation resistance were prepared by heat treating the Al-TiO2-MgO-Al2O3 composites at 1500 °C in N2-blowing, and the antioxidant mechanism of the composites was studied at 1500 °C in air. Results showed that a dense layer capable of hindering the diffusion of gases was formed in the outer part of the prepared metal, oxides and non-oxides composites. Under high temperature and air conditions, the presence of the dense layer and the metal components made the PO2 inside the composite be controlled by the diffusion and mass transfer of Al2O(g) and TiO(g), which provided a protective atmosphere for the non-oxides. After heat-treated at 1500 °C in air for 2 h, (Al2OC)x (AlN)1-x and Ti(C,N) inside the composite were well preserved, and the composition of the dense layer was transformed into MgAl2O4, TiO2 and Mg0·3Al1·4Ti1·3O5.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties · Magnesium Oxide Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Wetting, spreading and corrosion behavior of molten slag on dense MgO and MgO-C refractory10.1016/j.ceramint.2018.09.234 ↗
2. Strengthening of Al2O3-C slide gate plate refractories with microcrystalline graphite10.1016/j.ceramint.2017.04.178 ↗
3. The microstructure evolution and mechanical properties of MgO-C refractories with recycling Si/SiC solid waste from photovoltaic industry10.1016/j.ceramint.2018.06.057 ↗
4. Situation and development of production technology for clean steel in China and Abroad
5. Formation mechanism of (Al2OC)1-x(AlN)x solid solution in the Al-Si-Al2O3 composite at 1300 °C in flowing nitrogen
6. Theoretical analysis and synthesis of Al4O4C and Al2CO phase in the resin bonded Al-Al2O3 refractory in N2-flowing10.1016/j.ceramint.2017.10.060 ↗
7. New synthetic route to Al4O4C reinforced Al-Al2O3 composite materials10.1016/j.solidstatesciences.2015.05.006 ↗
8. Effect of Al addition on creep resistance of MgO-Al2O3, composite for sliding plate at 1400 °C10.1016/j.ceramint.2017.05.330 ↗
9. Phase evolution mechanism of non‐oxide bonded Al-Al2O3-MgO-ZrO2 composites at 1873 K in flowing nitrogen10.1111/jace.15356 ↗
10. Evolution mechanism of MgAlON in the Al-Al2O3-MgO composite at 1800 °C in flowing nitrogen10.1016/j.ceramint.2017.11.174 ↗
11. Wear mechanism of a novel Al-Si-MgAl2O4-Al2O3 composite used in the low vessel of an RH secondary refining furnace10.1016/j.ceramint.2019.02.202 ↗
12. In-situ synthesis mechanism of plate-shaped β-Sialon and its effect on Al2O3-C refractory properties10.1016/j.ceramint.2015.07.071 ↗
13. In situ synthesis mechanism of 15R-SiAlON reinforced Al2O3 refractories by Fe-Si liquid phase sintering10.1111/jace.15385 ↗
14. Enhancing electroreduction of CO2 to formate of Pd catalysts loaded on TiO2 nanotubes arrays by N, B㏒support modification
15. Effect of Pd concentration on the structural, morphological and photodiode properties of TiO2 nanoparticles10.1007/s10854-019-01095-5 ↗
16. Induced dielectric behavior in high dense AlxLa1-xTiO3 (x=0.2-0.8) nanospheres10.1007/s10854-019-02409-3 ↗
17. Influence of surface modification on the cutting performance of reaction-sintered Al2O3-TiOC ceramics10.1111/j.1551-2916.2008.02559.x ↗
18. Effect of precursor ratio on synthesis and optical absorption of TiON photocatalytic nanoparticles10.1111/j.1551-2916.2007.01600.x ↗
19. Structural and thermodynamic properties of TiCxNyOz, solid solution: experimental study and first-principles approaches10.1007/s11661-016-3553-0 ↗
20. Titanium-carbonitride-based hard alloys for cutting tools10.1016/0025-5416(88)90724-0 ↗
21. Development of functionally graded sintered hard10.1179/pom.1996.39.4.296 ↗
22. Cleanliness of low carbon aluminum-killed steels during secondary refining processes10.1002/srin.201200213 ↗
23. Synthesis of ultrafine titanium carbonitride powders10.1002/aoc.164 ↗
24. Mechanical alloying of a TiC-TiN ceramic system10.1016/S0924-0136(96)02828-2 ↗
25. Synthesis of nanocrystalline titanium carbonitride during milling of titanium and carbon in nitrogen atmosphere
26. Synthesis of titanium carbonitride phases by reactive milling of the elemental mixed powders10.1111/j.1551-2916.2005.00351.x ↗
27. Effects of additives on the synthesis of TiCxN1-x by a solid-gas mechanically induced self-sustaining reaction10.1016/j.ceramint.2018.01.179 ↗
28. Direct formation of titanium carbonitrides by SHS in nitrogen10.1016/j.ceramint.2004.07.013 ↗
29. Synthesis of titanium carbonitride nano-powder by carbothermal reduction of TiO210.1016/j.ijrmhm.2013.10.002 ↗
30. Formation of titanium carbonitride phases via the reduction of TiO2 with carbon in the presence of nitrogen10.1023/A:1004457622751 ↗
31. Design, microstructure and high temperature properties of in-situ Al3Ti and nano-Al2O3 reinforced 2024Al matrix composites from Al-TiO2 system10.1016/j.jallcom.2018.09.376 ↗
32. Formation of dense non-oxide layer in Al-TiO2-MgO-Al2O3 refractories at 1873 K in flowing N210.1016/j.ceramint.2019.06.180 ↗
33. Formation mechanism of Ti(C, N) solid solution in Al-brown fused alumina refractory at 1973 K in flowing N2
34. Chase · 1998
35. Thermodynamics of the Al2O3-Al4C3 system: I. Thermochemical functions of Al oxide, carbide and oxycarbides between 298 and 2100 K10.1016/j.jeurceramsoc.2006.06.009 ↗