Fiber induced time-lag during water droplet adsorption on carbon fiber reinforced silicon carbide (C/SiC) surfaces
Source abstract
Abstract
Abstract Many of the advantages that make C/SiC functional materials desirable are also largely responsible for the machining difficulties encountered. The time-lag of water droplet adsorption (WDA) arised from the complex fabricated carbon fiber precast body may cause cooling condition deterioration in near dry machining of C/SiC, which then gives rise to a lower machinability with respect to the surface integrity. However, little attention has been devoted to the fiber induced time-lag of WDA on C/SiC surfaces. In this study, theoretical models of WDA of two typical C/SiC surfaces, namely, pillar fiber ending and circle fiber ending C/SiC surfaces, were first established. Uni-directional C/SiC was fabricated to experimentally simulate the WDA process on these two typical surfaces. The complete WDA process on a single sample was analyzed first. Considering the stochastic shape of the flow channel, WDA experiments conducted on two typical C/SiC surfaces were repeated 2000 times. The frequency occurrence of the water droplet adsorption time (WDAT) of these 2000 experiments was fitted using the normal distribution function. The statistical evaluation methods indicated that the WDAT of a pillar fiber ending C/SiC surface lagged behind the WDAT of a circle fiber ending C/SiC surface. Furthermore, the time-lags were dependent on both the volume of the water droplet volume and increase in temperature. A critical discussion was conducted regarding the prevention of the WDA time-lag on C/SiC surfaces, and it is suggested that reducing the tiny droplet diameter of cooling mists and spray mists in advance and properly improving the cutting heat can limit, to some extent, the fiber induced time-lag of the WDA of C/SiC surfaces, which is an important factor for optimizing the cooling supply of near dry machining of C/SiC composites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Environmentally conscious machining of difficult-to-machine materials with regard to cuttingfluids10.1016/j.ijmachtools.2012.02.002 ↗
2. Weinert · 2004 · vol. 53 · 511
3. The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel10.1016/j.jmatprotec.2005.06.047 ↗
4. Near dry electrical discharge machining10.1016/j.ijmachtools.2007.06.001 ↗
5. Shaw · 1968
6. Heat generation and temperature prediction in metal cutting: a review and implications for high speed machining10.1016/j.ijmachtools.2005.07.024 ↗
7. Effect of tool wear on surface finish for a case of continuous and interrupted hard turning10.1016/j.jmatprotec.2005.04.119 ↗
8. Thermal analysis of grinding10.1016/j.cirp.2007.10.005 ↗
9. Arunachalam · 2004 · vol. 44 · 1481
10. Explosive boiling of liquid droplets at their superheat limits10.1016/j.ces.2004.11.010 ↗
11. A study on droplets and their distribution for minimum quantity lubrication (MQL)10.1016/j.ijmachtools.2010.05.001 ↗
12. Heat transfer in subcooled jet impingement boiling at high wall temperatures
13. Detachment of colloids from a solid surface by a moving air–water interface10.1016/j.jcis.2008.07.030 ↗
14. Incropera · 2001
15. Active control of the anisotropic wettability of the carbon fiber reinforced carbon and silicon carbide dual matrix composites (C/C-SiC)10.1016/j.apsusc.2014.11.183 ↗
16. Comparative study of micro topography on laser ablated C/SiC surfaces with typical uni-directional fiber ending orientations10.1016/j.ceramint.2016.01.173 ↗
17. Surface wetting of the C/SiC brake lining with micro-scale heat dissipation fins to cool off the brake system: influence of the fibre ending orientation and fin interval10.1016/j.ceramint.2017.05.101 ↗
18. On the wettability diversity of C/SiC surface: comparison of the ground C/SiC surface and ablated C/SiC surface from three aspects10.1016/j.apsusc.2016.05.061 ↗
19. Microstructure and ablation mechanism of C/C–SiC composites10.1016/j.jeurceramsoc.2013.08.026 ↗
20. Ablation behaviors of carbon/carbon composites with C–SiC–TaC multi-interlayers10.1016/j.apsusc.2009.07.006 ↗
21. Stoichiometry of the C + SiO2 reaction10.1111/j.1151-2916.1989.tb05964.x ↗
22. Morphology and microstructure of 2.5 dimension C/SiC composites ablated by oxyacetylene torch10.1016/j.ceramint.2008.06.008 ↗
23. Oxidation of ZrB2–SiC ultra-high temperature composites over a wide range of SiC content10.1016/j.jeurceramsoc.2012.05.021 ↗
24. Microstructure and ablation properties of zirconium carbide doped carbon/carbon composites10.1016/j.carbon.2009.09.035 ↗
25. Solid-state decomposition of silicon carbide for growing ultra-thin heteroepitaxial graphite films10.1063/1.1498962 ↗
26. Oxy-acetylene flame chemical vapour deposition of diamond films, Part I: the influence of deposition parameters on diamond morphology10.1016/S0040-6090(98)00504-5 ↗
27. Carbon formation from aromatic hydrocarbons II10.1016/0010-2180(66)90064-2 ↗
28. Oxidation resistance of HfB2–SiC composites for protection of carbon-based materials10.1016/j.actaastro.2006.11.007 ↗
29. Ablation behaviors of ultra-high temperature ceramic composites10.1016/j.msea.2007.02.040 ↗
30. Spreading of a droplet on a solid surface10.1002/app.1994.070520308 ↗
31. Experimental evidence of several time scales in drop spreading10.1021/la990769t ↗
32. The dynamics of capillary flow10.1103/PhysRev.17.273 ↗
33. Gao · 2010
34. Fang · 2016 · vol. 36 · 451