Effect of sintering additives on mechanical properties of Cf/SiC composites
Source abstract
Abstract
Abstract The Cf/SiC composites were prepared by precursor pyrolysis-hot pressing with AlN and B as sintering additives, and the effect of sintering additives on the microstructure and mechanical properties of the composites was investigated. In the composites, a SiC–AlN solid solution was formed, which was considered to be mainly due to the reactions between PCS and AlN during the pyrolysis of PCS instead of the inter-diffusion between original SiC and AlN. Although it was beneficial to the microstructure and mechanical properties of the matrix because of the formation of SiC–AlN solid solution that could strengthen the grain boundaries and suppress the coarsening of SiC grains in the matrix, AlN exhibited a small effect on the fiber/matrix interfacial bonding strength. As a result, AlN had little effect on the density and mechanical properties of the composites. In contrast, the density and mechanical properties of the composites were improved significantly by the introduction of a trace of B, and the density and strength increased with the amount of B. However, the maximum of fracture toughness was obtained in the composite with 0.5 wt.% B, which was mainly due to the desirable fiber/matrix interfacial bonding. In the case of composites with 1 wt.% B, the fracture toughness decreased in spite of the enhancement in the density and strength, which was mainly due to the strong fiber/matrix interfacial bonding.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Sintering of in-situ synthesized SiC–TiB2 composites with improved fracture toughness10.1111/j.1151-2916.1992.tb05600.x ↗
2. Fabrication and fracture behavior of novel SiC ceramics having rodlike grains10.1111/j.1151-2916.1992.tb04224.x ↗
3. Mechanical properties of β-SiC pressureless sintered with Al2O3 additions10.1016/0956-7151(94)90072-8 ↗
4. Microstructure and mechanical properties of hot-pressed silicon carbide–aluminum nitride composites10.1111/j.1151-2916.1992.tb08182.x ↗
5. Effect of the surface structure of Si–Ti–C–O fiber on the properties of three-dimensional fiber-reinforced silicon carbide composites10.2109/jcersj.105.1146 ↗
6. Fabrication of high performance SiC/SiC composite by polymer impregnation and pyrolysis method
7. Status of continuous fiber-reinforced ceramic matrix composite processing technology10.1002/9780470313008.ch26 ↗
8. Fiber-reinforced composites with polymer-derived matrix: processing, matrix formation and properties10.1016/S1359-835X(98)00128-6 ↗
9. Mechanical behavior and high-temperature performance of a woven Nicalon™/Si–N–C ceramic-matrix composite10.1111/j.1151-2916.1998.tb02550.x ↗
10. Preparation and mechanical properties of Si–C–O long fiber/alumina matrix composite10.2109/jcersj.103.1033 ↗
11. New materials in the Si–C–Al–O–N and related system10.1038/275434a0 ↗
12. Pressureless sintering of AlN–SiC composites10.1007/BF01124823 ↗
13. Phase relationships in the silicon carbide–aluminum nitride system10.1111/j.1151-2916.1988.tb07541.x ↗
14. Fabrication and characterization of SiC–AlN alloys10.1007/BF00586311 ↗
15. E. Bouillon, F. Langlais, R. Pailler, R. Naslain, et al., Conversion mechanisms of a polycarbosilane precursor into an SiC-based ceramic material, J. Mater. Sci. 26 (1991) 1333–1345.10.1007/BF00544474 ↗
16. Influence of fiber and interfacial properties on fracture behavior of fiber-reinforced ceramic composites10.1111/j.1151-2916.1991.tb06858.x ↗
17. Fiber coating concepts for brittle-matrix composites10.1111/j.1151-2916.1993.tb03749.x ↗
18. Detection of boron segregation to grain boundaries in silicon carbide by spatially resolved electron energy-loss spectroscopy10.1111/j.1551-2916.1999.tb20089.x ↗