Study of weldability of a Cr–Si modified heat-resisting alloy
Source abstract
Abstract
A cast heat-resistant alloy able to withstand carburization and metal dusting was developed to be used in the conducting pipes of reformed gas heaters for the direct reduction process. However, this alloy exhibits serious weldability problems in its as-cast condition and during the repair of aged pieces. Study of the microstructural and technological factors that affect weldability indicate that the use of low heat input (in the range of 630–950 kJ m −1 ) and a maximum interpass temperature of 150 ◦ C favors the welding repair of the high Cr–Si modified HK40 alloy. A solution annealing treatment prior to welding was necessary to obtain acceptable weldments. The commonly known buttering technique was not successful in this type of alloy. A series of microstructural phenomena, such as precipitation of secondary carbides, formation of intermetallic compounds (sigma phase and nickel silicide), as well as transformation of primary carbides, were observed to occur during aging, and they are suspected to be responsible for reducing the weldability of aged parts. © 2002 Elsevier Science B.V. All rights reserved.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Metal Alloys Wear and Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. D.B. Roach, J.A. VanEcho, in: V.G.Behal, A.S. Mellini (Eds.), Stainless Steel Castings, ASTM STP 756, pp. 275–311.
2. H. E. McGannon (Ed.), Direct Reduction Processes, The Making, Shaping and Treating of Steel, 1970, p. 417.
3. A. Velasco, S. Caballero, Carburization and metal dusting in HK 40 Steel, HYL, Internal Report, 1988.
4. A. Velasco, S. Caballero, Carburization, metal dusting and weldability of modified HK 40 alloy, HYL, Internal Report, 1995.
5. H.W. Ebert, Welding J. (November 1976), 939–945.
6. R.E. Avery, C.M. Schillmoller, Hydrocarbon Process (January 1988), 43–45.
7. C.H. Voelker, L.A. Zeis, Hydrocarbon Process (April 1972).
8. H.W. Ebert, Welding J. (1973 December) (Reprint).
9. G.E. Stapleton, Wisconsin Centrifugal Inc., Waukesha, WI.
10. H.W. Ebert, Welding J. (February 1984), 18–23.10.1364/AO.23.003759 ↗
11. A. Velasco, Repair welding of gas heaters tubes, HYL, Internal Report, 1993.
12. C. Steel, R.E. Pidgen, W. Engel, NACE International, Corrosion 83, Paper 265.
13. ASME Section IX Code for Boilers and Pressure Vessels.
14. Heat-Resistant Casting Alloys, Metallography, Structures and Phase Diagrams, Vol. 8, eighth ed., 1973.
15. ASTM E 18 Standard, Hardness test.
16. Tai · Mater. Sci. Technol. · 1985 · 1 · 38510.1179/mst.1985.1.5.385 ↗
17. Cast Stainless Steels, Properties and Selection Irons, Steels and High Performance Alloys, Vol. 1, 10th ed., 1986, pp. 910–923.
18. Aydin · Arch. Eisenhüttenwes · 1983 · 54 · 42110.1002/srin.198305267 ↗
19. R.L. Colwell, J.J. Hoffman, Weld Cracking in Modified Heat Resistant Castings, A Microstructural Investigation, NACE, Corrosion 98, Paper 423.
20. E. Folkhard, Welding Metallurgy of Stainless Steel, Springer, New York, 1988, pp. 35–38.10.1007/978-3-7091-8965-8 ↗