journal article·2021-03

Microstructure and oxidation behavior of an Al–Ni–Cr–Cu–MoO3–SiO2 composite coating on low-carbon steel

Didik Aryanto, Hariyati Hariyati, Pulung K. Karo, Agus S. Wismogroho, Wahyu B. Widayatno, Abdul Basyir, Nono Darsono, Satrio Herbirowo, Nurul T. Rochman, Alfian Noviyanto

Publisher page

Abstract

Abstract In the present study, an Al–Ni–Cr–Cu–MoO3–SiO2 composite coating with varying elemental compositions was deposited using the mechanical alloying technique. The composite coating structure before and after an oxidation test was studied using X-ray diffraction (XRD), three-dimensional optical microscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). A cyclic oxidation test was conducted in an 800 °C air atmosphere for 10 cycles (200 h). Based on the XRD, SEM, and EDX analyses, the coating comprised composite-refined Al, Ni, Cr, and Cu particles as well as coarse SiO2 particles. The composite coating had a thickness in the range of 36–59 μm, with good and continuous adherence to the substrate. The cyclic oxidation curve of the composite coating followed a parabolic rate law. The sample that contained 5.3 wt% MoO3 showed the best oxidation resistance after 10 oxidation cycles at 800 °C. This sample had a lower mass gain than the other samples. Moreover, this sample had a Kp of 1.2 × 10−3 mg2/cm2·s. Protective Al2O3 oxides formed on the composite coating surface with a thickness of 0.75–1.89 μm. This oxide scale was dense and fully adhered to the coating, thereby improving oxidation resistance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Preparation and properties of ceramic coating on Q235 carbon steel by plasma electrolytic oxidation10.1016/j.cap.2008.12.004 ↗
2. Preparation of ferrosilicon-aluminium coating using a mechanical alloying technique: study of thermal annealing on their structural characteristics10.1016/j.surfcoat.2017.12.041 ↗
3. Effect of annealing temperature on the oxidation behavior of ferrosilicon-aluminum-coated low carbon steel by mechanical alloying10.1016/j.jallcom.2019.153493 ↗
4. High-temperature oxidation behavior of SiO2 protective layer deposited on IN738LC superalloy by combustion CVD (CCVD)10.1016/j.apsusc.2009.07.092 ↗
5. A study of the erosion-corrosion behavior of nano-Cr2O3 particles reinforced Ni-based composite alloying layer in aqueous slurry environment10.1016/j.vacuum.2010.10.009 ↗
6. SiO2–Al2O3–glass composite coating on Ti–6Al–4V alloy: oxidation and interfacial reaction behavior10.1016/j.corsci.2013.05.010 ↗
7. Corrosion resistance enhancement of Ni-P-nano SiO2 composite coatings on aluminum10.1016/j.apsusc.2014.02.109 ↗
8. Cr2O3 nanoparticles: a promising candidate to improve the mechanical properties and corrosion resistance of Ni-Co alloy coatings10.1016/j.ceramint.2018.01.044 ↗
9. Experimental study on the microstructural and anti-corrosion behaviour of Co-deposition Ni-Co-SiO2 composite coating on mild steel10.1016/j.dt.2017.10.001 ↗
10. Microstructure and tribological properties of plasma sprayed TiCN-Mo based composite coatings10.1016/j.apsusc.2018.09.063 ↗
11. Effect of WC addition on microstructure and tribological properties of bimodal aluminum composite coatings fabricated by laser surface alloying10.1016/j.matchemphys.2019.05.089 ↗
12. Microstructure and oxidation behavior of MoSi2-based coating on carbon/carbon composites10.1016/j.ceramint.2019.07.210 ↗
13. Microstructures and properties of Ni/TiC/La2O3 reinforced Al based composite coatings by laser cladding10.1016/j.optlastec.2019.04.002 ↗
14. Microstructure and properties of TiN/Fe-based amorphous composite coatings fabricated by reactive plasma spraying10.1016/j.jallcom.2019.01.171 ↗
15. Mechanical properties and corrosion resistance of Ni-Co-SiC composite coatings by magnetic field-induced jet electrodeposition10.1016/j.jallcom.2019.03.391 ↗
16. Preparation of ZrC-SiC composite coatings by chemical vapor deposition and study of co-deposition mechanism10.1016/j.jmst.2019.07.005 ↗
17. Microstructure and properties of sol-enhanced Co-P-TiO2 nano-composite coatings10.1016/j.jallcom.2019.04.047 ↗
18. High-temperature oxidation response of Mo–Si–B composites with TiO2W/SiCW addition10.1016/j.ceramint.2019.05.120 ↗
19. New coating technique for Al–B4C composite coatings by mechanical milling and composite coating10.1007/s11106-015-9662-2 ↗
20. Fabrication of nanocrystalline TiC coating on AISI D2 steel substrate via high-energy mechanical alloying of Ti and C10.1016/j.powtec.2015.10.030 ↗
21. Study of W-Co ODS coating on stainless steels by mechanical alloying10.1016/j.surfcoat.2018.03.047 ↗
22. Investigation of Cr-Al composite coatings fabricated on pure Ti substrate via mechanical alloying method: effects of Cr-Al ratio and milling time on coating, and oxidation behavior of coating10.1016/j.jallcom.2015.11.094 ↗
23. Influence of Si on the target oxide poisoning during reactive arc evaporation of (Al,Cr)2O3 coatings10.1016/j.vacuum.2013.06.008 ↗
24. Effects of Cu and Zn on microstructures and mechanical behavior of the medium-entropy aluminum alloy10.1016/j.jallcom.2019.153092 ↗
25. Effect of trace Ni addition on microstructure, mechanical and corrosion properties of the extruded Mg–Gd–Y–Zr–Ni alloys for dissoluble fracturing tools
26. Effect of MoO3 ceramic oxide reinforcement particulates on the microstructure and corrosion behaviour of Al alloy composites processed by P/M route10.1016/j.mtcomm.2020.101655 ↗
27. Formation and cyclic oxidation resistance of Hf-Co-modified aluminide coatings on nickel base superalloys10.1016/j.matchemphys.2013.09.016 ↗
28. Effect of process parameters on the formation of Fe-Al intermetallic coating fabricated by mechanical alloying
29. In situ coating of low carbon steel with Ni-Al-Fe powder mixture via mechanical alloying10.1016/j.surfcoat.2017.02.046 ↗
30. Preparation of Ti–Cr and Ti–Cu flame-retardant coatings on Ti–6Al–4V using a high-energy mechanical alloying method: a preliminary research10.1016/j.matdes.2011.09.017 ↗
31. Influence of annealing temperature on the structure and properties of the nanograined NiAl intermetallic coatings produced by using mechanical alloying10.1016/j.surfcoat.2012.11.073 ↗
32. Fabrication of Ti–Al coatings by mechanical alloying method10.1016/j.surfcoat.2006.06.044 ↗
33. High temperature cyclic oxidation resistance of 50Cr-50Al coatings mechanically alloyed on low carbon steel10.1016/j.jallcom.2017.10.163 ↗
34. Synthesis of the Ni-Al coatings on different metallic substrates by mechanical alloying and subsequent laser treatment10.1016/j.jallcom.2016.11.189 ↗
35. Suprianto, Investigation of W-Ti ODS coating on SUS304 steel fabricated by mechanical alloying technique10.1016/j.surfcoat.2018.02.018 ↗
36. Microstructures and oxidation behavior of Al-CrMnFeCoMoW composite coatings on Ti-6Al-4V alloy substrate via high-energy mechanical alloying method10.1016/j.jallcom.2018.11.266 ↗
37. Contribution of Mg addition on the high temperature cyclic oxidation resistance of NiAlCr alloys10.1016/j.corsci.2018.08.004 ↗
38. Modification of NiCoCrAlY with Pt: Part I. Effect of Pt depositing location and cyclic oxidation performance10.1016/j.jmst.2018.09.039 ↗
39. Characterization and sintering of MoO3 prepared by thermal decomposition of hexaammonium heptamolybdate tetrahydrate10.1016/S0025-5408(96)00167-5 ↗
40. Rare-earth nitrate additives for the sintering of silicon carbide10.1016/j.jeurceramsoc.2013.05.017 ↗
41. Birks · 2006 · vols. 83–86
42. Oxidation of ferritic and ferritic-martensitic steels in flowing and static supercritical water10.1016/j.corsci.2015.10.017 ↗
43. Effect of chromium content on the oxidation behaviour of ferritic steels for applications in steam atmospheres at high temperatures10.1007/s11085-008-9134-x ↗
44. The role of dissolved oxygen in supercritical water in the oxidation of ferritic-martensitic steel10.1016/j.supflu.2015.10.017 ↗
45. Deformation, cracking and fracture behavior of dynamically-formed oxide layers on molten metals