journal article·2018-11

A simple non-toxic simultaneous selenization/sulfurization process for Cu(In, Ga)(S, Se)2 solar cells

Yi-Cheng Lin, Siang-Jin Wei, Yuan-Jun Liang, Wei-Jhe Syus

Publisher page

Abstract

Abstract This paper proposes a non-toxic simultaneous selenization/sulfurization process to produce Cu(In,Ga)(S,Se)2 (CIGSSe) solar cells without the need for the conventional two-stage process using toxic H2Se/H2S gases. The absorber layer is applied via sputtering with Cu-In-Ga ternary targets, whereupon non-toxic selenium and sulfur vapor are introduced simultaneously to produce chalcopyrite CIGSSe film. Experiment results demonstrate that the total sulfur content of the absorber layer increases with an increase in the S/(S + Se) ratio. When the S/(S + Se) ratio ≧ 0.12, the sulfur content of the surface absorber layer is higher than inside the sample. This contributes to an increase in the surface energy gap and Voc of the solar cell. However, an excessively high S/(S + Se) ratio can undermine the crystallinity of the CIGSSe while introducing phase segregation at the surface of the absorber layer as well as ordered vacancy compounds (OVCs) and secondary phases, which can decrease cell efficiency. A suitable proportion of sulfur in the absorber layer can inhibit excessive growth of the Mo(S,Se)2 layer and thereby enhance cell efficiency. A small number of CuGaSe2 grains were observed at the bottom of the CIGSSe absorber layer in specimens with various S/(S + Se) ratios. A maximum cell efficiency of 12.8% was achieved when the S/(S + Se) ratio was 0.12. This cell efficiency is close to the reference specimen fabricated using a two-stage selenization/sulfurization process based on toxic H2Se/H2S gases.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Ch.H. Fischer, Determination of the band gap depth profile of the penternary Cu(In(1- X )GaX) (SYSe(1-Y))2 chalcopyrite from its composition gradient10.1063/1.1786340 ↗
2. Band-gap engineering in CuIn(Se,S)2 absorbers for solar cells10.1016/j.solmat.2008.11.014 ↗
3. Influence of different sulfur to selenium ratios on the structural and electronic properties of Cu(In,Ga)(S,Se)2 thin films and solar cells formed by the stacked elemental layer process10.1063/1.4900991 ↗
4. Advanced characterization of electrodeposition-based high efficiency solar cells: non-destructive Raman scattering quantitative assessment of the anion chemical composition in Cu(In,Ga)(S,Se)2 absorbers10.1016/j.solmat.2015.06.056 ↗
5. Composition dependence of defect energies and band alignments in the Cu(In1−xGax)(Se1−ySy)2 alloy system10.1063/1.1432126 ↗
6. Ga homogenization by simultaneous H2Se/H2S reaction of Cu-Ga-In precursor10.1016/j.solmat.2010.04.050 ↗
7. Fabrication of pentanary Cu(In,Ga)(Se,S)2 absorbers by selenization and sulfurization10.1016/j.solmat.2009.02.004 ↗
8. Three-step H2Se/Ar/H2S reaction of Cu-In-Ga precursors for controlled composition and adhesion of Cu(In,Ga)(Se,S)2 thin films10.1063/1.4704390 ↗
9. Composition and bandgap control in Cu(In,Ga)Se2-based absorbers formed by reaction of metal precursors10.1002/pip.2494 ↗
10. Cu-In-Ga metal precursors sputter deposted from a single ternary target for Cu(lnGa)(SeS)2 film formation
11. CIS module pilot processing applying concurrent rapid selenization and sulfurization of large area thin film precursors10.1016/S0040-6090(03)00249-9 ↗
12. Second generation CIS solar modules10.1016/j.solener.2004.05.011 ↗
13. Tuning the band gap of Cu(In,Ga)Se2 thin films by simultaneous selenization/sulfurization10.1016/j.matlet.2016.06.104 ↗
14. Improving the efficiency of a Cu2ZnSn(S,Se)4 solar cell using a non-toxic simultaneous selenization/sulfurization process10.1016/j.mssp.2017.11.005 ↗
15. Study on phase formation mechanism of non- and near-stoichiometric Cu2ZnSn(S,Se)4 film prepared by selenization of Cu-Sn-Zn-S precursors10.1021/cm403423e ↗
16. Efficiency enhancement by adding SnS powder during selenization for Cu2ZnSn(S,Se)4 thin film solar cells10.1016/j.solmat.2015.10.037 ↗
17. Ex- and in-situ investigations of sulfur diffusion into Cu(In,Ga)Se2 thin films10.1016/j.tsf.2014.10.044 ↗
18. Cu(In,Ga)Se2 thin films without Ga segregation prepared by the single - step selenization of sputter deposited Cu-In-Ga-Se precursor layers10.1039/c2ee22804a ↗
19. Effect of Cu/(In+Ga) ratios on the secondary phases and the performance of Cu2InGa(S,Se)4 thin film solar cells10.1016/j.jallcom.2016.08.127 ↗
20. Preparation of CuIn(S,Se) 2 thin films by thermal crystallization in sulfur and selenium atmosphere10.1016/S0022-3697(03)00106-9 ↗
21. Compositional depth profiling of polycrystalline thin films by grazing-incidence X-ray diffraction10.1107/S002188980601987X ↗
22. A new mass production technology for high- efficiency thin- film CIS- absorber formation10.1109/JPHOTOV.2014.2302235 ↗
23. Martha Ch. Lux-Steiner, 11.3% efficiency Cu(In,Ga)(S,Se)2 thin film solar cells via drop-on-demand inkjet printing10.1039/C6EE00587J ↗
24. Advanced diagnostic and control methods of processes and layers in CIGS solar cells and modules10.1002/pip.966 ↗
25. Raman microprobe characterization of electrodeposited S-rich CuIn(S,Se)2 for photovoltaic applications: microstructural analysis10.1063/1.2734103 ↗
26. Role of Mo:Na layer on the formation of MoSe2 phase in Cu(In,Ga)Se2 thin film solar cells10.1016/j.solmat.2016.06.024 ↗
27. A study on MoSe2 layer of Mo contact in Cu(In,Ga)Se2 thin film solar cells10.1016/j.tsf.2014.04.016 ↗
28. Impact of Mo barrier layer on the formation of MoSe2 in Cu(In,Ga)Se2 solar cells10.1016/j.jallcom.2015.11.194 ↗
29. Hybrid silver nanowires/nanogold particles film for a Cu(In,Ga)Se2 thin film solar cell10.1016/j.cjph.2017.06.005 ↗