Investigation on Flaw Evolution of Additively Manufactured Al2O3 Ceramic by In Situ X-ray Computed Tomography
Source abstract
Abstract
The additive manufacturing process may create flaws inside ceramic materials. The flaws have a significant influence on the macroscopic mechanical behavior of ceramic materials. In order to reveal the influence of flaws on the mechanical behavior of additively manufactured ceramic, flaw evolution under mechanical loads was studied by in situ X-ray computed tomography (XCT) in this work. In situ compression XCT tests were conducted on stereolithographic additively manufactured Al2O3 ceramic. The three-dimensional full-field morphologies at different compressive loads were obtained. The evolution of flaws, including pores, transverse cracks, and vertical cracks, during compressive loading was observed. The number and volume of pores, transverse cracks, and vertical cracks were extracted. It was found that most pores and transverse cracks tend to be compacted. However, high compressive loads cause vertical cracks near the upper surface to expand, leading to the failure of the specimen. Real flaws with morphological and positional information were introduced into the finite element models. The influence of different types of flaws on the mechanical behavior is discussed. It was found that vertical cracks have a greater influence on mechanical behavior than do transverse cracks under compression. The presence of transverse cracks contributes to the evolution of vertical cracks. This study may be helpful for process optimization and performance enhancement of additively manufactured ceramic materials.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Institute of Advanced Structure Technology, Beijing Institute of Technology, Beijing 100081, China
College of Engineering, Peking University, Beijing 100871, China
Funding
National Natural Science Foundation of China · National Science and Technology Major Project · Beijing Institute of Technology Research Fund Program for Young Scholars
References (21)
Show source-provided references
1. Review on ultra-high temperature boride ceramics10.1016/j.pmatsci.2020.100651 ↗
2. Pre-oxidation temperature optimization of ultra-high temperature ceramic components: Flexural strength testing and residual stress analysis10.1016/j.ceramint.2014.12.079 ↗
3. Additive manufacturing methods and modelling approaches: A critical review10.1007/s00170-015-7576-2 ↗
4. Additive manufacturing (3D printing): A review of materials, methods, applications and challenges10.1016/j.compositesb.2018.02.012 ↗
5. Additive manufacturing of advanced ceramic materials10.1016/j.pmatsci.2020.100736 ↗
6. Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities10.1111/jace.13700 ↗
7. Partially stabilized zirconia moulds fabricated by stereolithographic additive manufacturing via digital light processing10.1016/j.msea.2019.138537 ↗
8. Effects of fine grains and sintering additives on stereolithography additively manufactured Al2O3 ceramic10.1016/j.ceramint.2020.09.071 ↗
9. Stereolithography additive manufacturing and sintering approaches of SiC ceramics10.1016/j.oceram.2020.100046 ↗
10. Additive Manufacturing of Ceramics: Stereolithography versus Binder Jetting
11. Fractography of zirconia-specimens made using additive manufacturing (LCM) technology10.1016/j.jeurceramsoc.2017.03.018 ↗
12. Mechanical characterization of ceramics by means of a 3D defect analysis10.1016/j.ceramint.2014.10.055 ↗
13. Three-dimensional reconstruction of ceramic membrane with internal defects based on ultrasound imaging technique applying triangular matrix-synthetic aperture focusing10.1016/j.ceramint.2020.06.109 ↗
14. Strength of additively manufactured alumina10.1016/j.jeurceramsoc.2020.03.073 ↗
15. Flexural strength and Weibull analysis of Y-TZP fabricated by stereolithographic additive manufacturing and subtractive manufacturing10.1016/j.jeurceramsoc.2019.10.058 ↗
16. X-Ray Microcomputed Tomography in Additive Manufacturing: A Review of the Current Technology and Applications10.1089/3dp.2018.0060 ↗
17. X-ray computed tomography for additive manufacturing: A review10.1088/0957-0233/27/7/072001 ↗
18. Effects of defects on mechanical properties in metal additive manufacturing: A review focusing on X-ray tomography insights10.1016/j.matdes.2019.108385 ↗
19. Effects of solid loading on stereolithographic additively manufactured ZrO2 ceramic: A quantitative defect study by X-ray computed tomography10.1016/j.ceramint.2021.05.149 ↗
20. X-ray tomography of additive-manufactured zirconia: Processing defects—Strength relations10.1016/j.jeurceramsoc.2019.04.010 ↗
21. An in situ microtomography apparatus with a laboratory x-ray source for elevated temperatures of up to 1000 °C10.1063/5.0038026 ↗