journal article·2025-02-08Open access

Experimental Investigation of Phase Change Material-Based Battery Pack Performance Under Elevated Ambient Temperature

Mohammad J. Ganji, Martin Agelin-Chaab, Marc A. Rosen

Batteries· Volume 11· Issue 2

Abstract

This study experimentally assesses the thermal performance of a proposed phase change material (PCM)-based battery pack under elevated ambient temperatures. In addition, the novel approach of the research addresses scenarios where the ambient temperature reaches the PCM’s melting point while maintaining the initial temperature at the ideal operating point of 22 °C. The experiments employed nine 2500 mAh 18650 lithium-ion cells connected in series and subjected to constant-current discharges of 1C and 3C, with a conventional air-cooled system as the baseline and paraffin as the PCM. The results indicate that as the ambient temperature reached the PCM’s melting point, approximately 98% utilization of the PCM around the heating cell was achieved. Additionally, the PCM demonstrates noticeable advantages over the baseline by stabilizing the temperature profile and reducing the maximum temperature increase rate from over 18 °C in the baseline system to around 7 °C. Notably, under a high-load (3C) discharge rate, the PCM-based system successfully maintained battery temperatures below 42 °C, demonstrating its effectiveness under demanding operational scenarios. These findings establish a critical baseline for PCM-based BTMSs operating under elevated ambient temperatures and up to the melting point of the PCM, thereby informing future research and development of more efficient PCM-based thermal management solutions.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Battery Technologies Research · Advanced Battery Materials and Technologies · Advanced battery technologies research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Engineering and Applied Science, Ontario Tech University, Oshawa, ON L1G 0C5, Canada

Funding

Natural Sciences and Engineering Research Council of Canada (NSERC)

References (38)

Show source-provided references
1. Battery thermal management systems (BTMs) based on phase change material (PCM): A comprehensive review10.1016/j.cej.2021.132741 ↗
2. Experimental and numerical studies on air cooling and temperature uniformity in a battery pack10.1002/er.4018 ↗
3. Leng, F., Tan, C.M., and Pecht, M. (2015). Effect of temperature on the aging rate of Li ion battery operating above room temperature. Sci. Rep., 5.10.1038/srep12967 ↗
4. A review of thermal runaway prevention and mitigation strategies for lithium-ion batteries
5. Cooling efficiency improvement of air-cooled battery thermal management system through designing the flow pattern10.1016/j.energy.2018.11.011 ↗
6. Cooling performance optimization of air-cooled battery thermal management system10.1016/j.applthermaleng.2021.117242 ↗
7. Heat dissipation optimization for a serpentine liquid cooling battery thermal management system: An application of surrogate assisted approach10.1016/j.est.2021.102771 ↗
8. Investigation on the thermal performance of a battery thermal management system using heat pipe under different ambient temperatures10.1016/j.enconman.2017.10.063 ↗
9. Natural convection in an internally finned phase change material heat sink for the thermal management of photovoltaics10.1016/j.solmat.2011.01.008 ↗
10. Effects of different phase change material thermal management strategies on the cooling performance of the power lithium ion batteries: A review10.1016/j.jpowsour.2019.227228 ↗
11. An innovative battery thermal management with thermally induced flexible phase change material10.1016/j.enconman.2020.113145 ↗
12. A review of phase change materials for the thermal management and isothermalisation of lithium-ion cells10.1016/j.est.2019.100887 ↗
13. Numerical investigation on PCM encapsulation shape used in the passive-active battery thermal management10.1016/j.energy.2019.116840 ↗
14. Experiment and simulation of a LiFePO4 battery pack with a passive thermal management system using composite phase change material and graphite sheets10.1016/j.jpowsour.2014.11.068 ↗
15. An innovative practical battery thermal management system based on phase change materials: Numerical and experimental investigations10.1016/j.applthermaleng.2017.08.172 ↗
16. Modeling of passive thermal management for electric vehicle battery packs with PCM between cells10.1016/j.applthermaleng.2014.07.037 ↗
17. Influence of PCM configuration and optimization of PCM proportion on the thermal management of a prismatic battery with a combined PCM and air cooling structure10.1016/j.est.2023.110340 ↗
18. Effect of finned networks on PCM based battery thermal management system for cylindrical Li-ion batteries10.1016/j.csite.2024.104572 ↗
19. Thermal performance analysis of a new type of branch-fin enhanced battery thermal management PCM module10.1016/j.renene.2023.02.083 ↗
20. Improving the cooling performance of cylindrical lithium-ion battery using three passive methods in a battery thermal management system10.1016/j.applthermaleng.2023.120320 ↗
21. Effect of fin design and continuous cycling on thermal performance of PCM-HP hybrid BTMS for high ambient temperature applications10.1016/j.est.2023.109360 ↗
22. An experimental study on thermal management of lithium-ion battery packs using an improved passive method10.1016/j.applthermaleng.2018.02.011 ↗
23. Thermal management of Li-ion batteries with passive thermal regulators based on composite PCM materials10.1016/j.est.2024.111661 ↗
24. Composite phase change material with room-temperature-flexibility for battery thermal management10.1016/j.cej.2021.131116 ↗
25. Thermal performance enhancement with snowflake fins and liquid cooling in PCM-based battery thermal management system at high ambient temperature and high discharge rate10.1016/j.est.2024.111754 ↗
26. Thermal performance and structural optimization of a hybrid thermal management system based on MHPA/PCM/liquid cooling for lithium-ion battery10.1016/j.applthermaleng.2023.121341 ↗
27. Performance of thermal management system based on PCM/forked liquid-cold plate for 18650 cylindrical battery10.1016/j.est.2024.112071 ↗
28. A novel thermal management system combining phase change material with wavy cold plate for lithium-ion battery pack under high ambient temperature and rapid discharging10.1016/j.applthermaleng.2024.122803 ↗
29. Experimental and numerical analysis of a hybrid cooling concept for an electric battery module10.1016/j.ijheatfluidflow.2024.109320 ↗
30. Investigation of thermal properties of phase change materials for novel hybrid thermal management strategies for cylindrical Li-ion cells10.1016/j.applthermaleng.2024.122471 ↗
31. Experimental and parametric analysis of a novel hybrid thermal management strategy for cylindrical lithium-ion cells10.1002/htj.23063 ↗
32. Halliday, D., Resnick, R., and Walker, J. (2012). Fundamentals of Physics, John Wiley Sons. [12th ed.].
33. Numerical study of PCM thermal behavior of a novel PCM-heat pipe combined system for Li-ion battery thermal management10.1016/j.applthermaleng.2022.118293 ↗
34. Describing the uncertainties in experimental results10.1016/0894-1777(88)90043-X ↗
35. Experimental optimization of partial metallic wire mesh configuration applicable in thermal energy storage systems10.1016/j.applthermaleng.2022.119274 ↗
36. Heat transfer characteristics of thermal energy storage system using PCM capsules: A review10.1016/j.rser.2007.06.009 ↗
37. Passive and hybrid battery thermal management system by cooling flow control, employing nano-PCM, fins, and metal foam10.1016/j.energy.2023.129809 ↗
38. Cengel, Y.A. (2014). Heat Transfer. Encyclopedia of Energy Engineering and Technology—Four Volume Set, CRC Press.