journal article·2020-03-05Open access

Effect of Post Heat-Treatment on the Microstructure, Tensile and Fatigue Properties of Al 3003 Alloy Manufactured by Strip Casting Process

Min-Seok Baek, Kwangjun Euh, Chang-Yeol Jeong, Kee-Ahn Lee

Abstract

Al 3003 alloy was manufactured by strip casting process, and the effect of post heat-treatment on tensile and fatigue properties was investigated. The strip cast Al 300 alloy exhibited a unique globular shaped rapid-cooled solidification structure, and the microstructural characteristic remained after heat-treatment. Asstrip cast (F) and heat-treated (O) alloys were commonly composed of Al matrix and strengthening phases such as Al6(Mn,Fe), α-Al(Mn,Fe)Si. In the phase analysis and Factsage simulation result, Al6(Mn,Fe) fraction increased while α-Al(Mn,Fe)Si fraction decreased after heat-treatment. Strengthening phases were more uniformly and finely distributed in the case of O alloy, than F alloy. In the Vickers hardness results, F alloy (measured 59.7 Hv) showed higher hardness than O alloy (measured 53.4 Hv). The yield strengths (YS) and ultimate tensile strengths (UTS) measured 124.8 MPa and 166.4 MPa (F alloy), and 111.2 MPa and 167.2 MPa (O alloy), respectively. F alloy exhibited superior YS compared to O alloy, while UTSs were similar in both alloys. For elongation, the F alloy (19.6%) had a lower value than the O alloy (23.0%). High cycle fatigue tests were performed at room temperature under a stress ratio (R) of 0.1 and frequency (F) of 10 Hz. The F alloy exhibited higher fatigue than the O alloy under all cyclic stress conditions. However, the deviation in the fatigue property of the F alloy was relatively broader than the O alloy. Tensile and fatigue fracture surfaces were examined, and the tensile and fatigue deformation mechanisms of the strip cast Al 3003 alloy were also discussed.
Source: openalex_inverted_index · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. 10.1023/B:JMSC.0000013884.69611.7210.1023/B:JMSC.0000013884.69611.72 ↗
2. Davis · 1993 · 33
3. 10.2320/matertrans.44.261710.2320/matertrans.44.2617 ↗
4. Haga · 2004 · 153
5. 10.1007/s10853-009-3393-z10.1007/s10853-009-3393-z ↗
6. Sum · 2006 · 32
7. 10.1016/S1359-6454(03)00160-510.1016/S1359-6454(03)00160-5 ↗
8. 10.1007/BF0173015010.1007/BF01730150 ↗
9. 10.1557/JMR.1992.323510.1557/JMR.1992.3235 ↗
10. 10.1007/BF0265173110.1007/BF02651731 ↗
11. 10.1016/S1359-6454(02)00085-X10.1016/S1359-6454(02)00085-X ↗
12. Warmuzek · 2004 · 157
13. 10.2320/matertrans.M201525910.2320/matertrans.M2015259 ↗
14. 10.1007/s12540-018-0123-610.1007/s12540-018-0123-6 ↗
15. 10.1016/j.jallcom.2008.04.00510.1016/j.jallcom.2008.04.005 ↗
16. 10.1080/1478643041000170178810.1080/14786430410001701788 ↗
17. 10.1007/BF0117403310.1007/BF01174033 ↗
18. Jung · 2002 · 54
19. 10.1016/j.actamat.2011.11.00310.1016/j.actamat.2011.11.003 ↗
20. 10.2320/matertrans.M201525910.2320/matertrans.M2015259 ↗
21. 10.1016/j.ijplas.2014.08.00610.1016/j.ijplas.2014.08.006 ↗
22. 10.1016/j.matdes.2015.11.06910.1016/j.matdes.2015.11.069 ↗
23. 10.1111/ffe.1215810.1111/ffe.12158 ↗
24. 10.3365/KJMM.2014.53.3.16910.3365/KJMM.2014.53.3.169 ↗
25. 10.5228/KSTP.2017.26.5.30610.5228/KSTP.2017.26.5.306 ↗
26. 10.1016/j.msea.2016.10.00310.1016/j.msea.2016.10.003 ↗
27. 10.1007/s12540-018-0158-810.1007/s12540-018-0158-8 ↗