journal article·2022-04-05Open access

Effect of Cu on the Microstructure of Al-8Zn-2.5Mg-xCu Alloys Fabricated by Twin roll casting

Dong-Guk Kim, Yong hee Jo, Yun-Soo Lee, Yong-You Kim, Hyoung-Wook Kim, Jung-Ki Kim

Abstract

The effect of Cu content on the microstructure and mechanical properties of Al-8.0Zn-2.5Mg-xCu (x: 0, 1, 2, 3) aluminum alloys manufactured by the twin-roll casting process was investigated. The Al-8.0Zn-2.5Mg-xCu alloy showed an increase in surface defects with increasing Cu content. This is because the amount of residual liquid in the final solidification region increased from 9.6 wt.% to 18.3 wt.% as the Cu content increased from 0Cu to 3 Cu alloy. For the 3Cu alloy, as the amount of residual liquid in the final solidification region exceeded the critical point, a large number of surface defects and internal shrinkage defect were observed. The main secondary phases of the four alloys were the T(Mg32(Al, Zn)49) and η(MgZn2) phases, and their fraction increased with Cu content. These secondary phases mainly existed in the center segregation band, and a fine η(MgZn2) phase was additionally observed. In terms of mechanical properties, as the Cu content increased, the hardness of the center matrix, secondary phase, and overall hardness increased respectively. Although the yield strength increased, the tensile strength and elongation decreased because the center segregation band was widened from 684 μm to 790 μm with increasing Cu content.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. 10.2320/matertrans.L-MZ20113210.2320/matertrans.L-MZ201132 ↗
2. Borns · 2005 · 1387
3. 10.3365/KJMM.2021.59.8.51510.3365/KJMM.2021.59.8.515 ↗
4. 10.1016/j.ijimpeng.2004.04.01610.1016/j.ijimpeng.2004.04.016 ↗
5. 10.3365/KJMM.2020.58.1.710.3365/KJMM.2020.58.1.7 ↗
6. 10.1016/j.matchar.2017.03.02410.1016/j.matchar.2017.03.024 ↗
7. 10.1007/s12540-017-6275-y10.1007/s12540-017-6275-y ↗
8. 10.3365/KJMM.2020.58.3.15110.3365/KJMM.2020.58.3.151 ↗
9. 10.1016/j.jmatprotec.2004.04.01810.1016/j.jmatprotec.2004.04.018 ↗
10. 10.1007/s11663-012-9659-x10.1007/s11663-012-9659-x ↗
11. 10.1016/j.jmatprotec.2005.02.12710.1016/j.jmatprotec.2005.02.127 ↗
12. 10.1016/j.jmatprotec.2014.11.03110.1016/j.jmatprotec.2014.11.031 ↗
13. 10.1007/s11669-011-9911-010.1007/s11669-011-9911-0 ↗
14. 10.4028/www.scientific.net/MSF.519-521.33910.4028/www.scientific.net/MSF.519-521.339 ↗
15. 10.1016/j.matdes.2014.05.00310.1016/j.matdes.2014.05.003 ↗
16. 10.1016/j.jallcom.2003.11.17510.1016/j.jallcom.2003.11.175 ↗
17. 10.1179/02670839910150683210.1179/026708399101506832 ↗
18. 10.1016/j.jallcom.2019.02.22810.1016/j.jallcom.2019.02.228 ↗
19. 10.3365/KJMM.2019.57.1.2810.3365/KJMM.2019.57.1.28 ↗
20. Bollinghaus · 2008 · 127
21. 10.1016/S0921-5093(99)00676-010.1016/S0921-5093(99)00676-0 ↗
22. 10.1007/BF0266109010.1007/BF02661090 ↗
23. 10.1016/j.matchar.2014.04.00410.1016/j.matchar.2014.04.004 ↗
24. 10.1016/j.matdes.2014.05.00310.1016/j.matdes.2014.05.003 ↗
25. 10.1016/j.msea.2004.09.01310.1016/j.msea.2004.09.013 ↗
26. 10.1007/s12613-014-1029-z10.1007/s12613-014-1029-z ↗
27. 10.1007/s11661-013-1709-810.1007/s11661-013-1709-8 ↗
28. 10.1007/s11661-015-3050-x10.1007/s11661-015-3050-x ↗
29. 10.1016/j.jmapro.2021.02.03110.1016/j.jmapro.2021.02.031 ↗
30. 10.1007/s12540-019-00499-610.1007/s12540-019-00499-6 ↗
31. 10.1007/3-540-27460-X_110.1007/3-540-27460-X_1 ↗
32. CH · 1996 · 93
33. 10.1016/j.msea.2021.14108310.1016/j.msea.2021.141083 ↗
34. 10.1007/s11661-005-0141-010.1007/s11661-005-0141-0 ↗
35. 10.1016/j.scriptamat.2008.07.02010.1016/j.scriptamat.2008.07.020 ↗
36. Zhang · 2020 · 156481