journal article·2025-02-05Open access

Precipitation Behavior and Mechanical Properties of High-Nitrogen Austenitic Stainless Steel According to Chemical Composition and Heat Treatment Temperature

Ki-Hwan Kwon, Seong Hoon Kim, Hyo-Haeng Jo, Jinjong Lee, Heon-Young Ha, Chang-Hoon Lee, Jae-Suk Jeong, Tae-Ho Lee, Nam Hyun Kang

Abstract

The precipitation behavior and mechanical properties of high-nitrogen austenitic stainless steels were investigated for various chemical compositions and solution treatment temperatures. For this study, Fe-22.1Cr-12.2Ni-5.1Mn-2.1Mo alloys with three different sets of Nb, V, and N contents were prepared, and two distinct solution treatment temperatures were applied. An increase in Nb or N content resulted in finer austenite grain size, attributed to the formation of additional precipitates, such as Z-phase and (Nb,V)(C,N), at the grain boundaries. Notably, the effect of a 0.07 wt% increase in Nb content was found to be comparable to more than a 100oC reduction in solution treatment temperature. The yield strength was observed to increase with decreasing grain size, consistent with the Hall-Petch relationship. When the grain size effect was excluded, and in the absence of Z-phase, a higher N content led to an increase in strength due to solid solution strengthening. On the other hand, an increase in Nb content resulted in reduced strength, even though there was little change in the austenite N content. Thermodynamic analysis suggested that Z-phase precipitation may replace MX particles, which could account for the observed decrease in strength. While Z-phase precipitation promotes a finer grain size, coarse Z-phase particles did not contribute effectively to precipitation hardening. Therefore, to achieve higher strength in high-nitrogen austenitic stainless steels, alloy design must be optimized, particularly when Nb addition is considered.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. 10.1038/d41586-022-01733-910.1038/d41586-022-01733-9 ↗
2. 10.1016/j.energy.2023.12816910.1016/j.energy.2023.128169 ↗
3. Hadid Subki · 2020 · 1
4. 10.1016/j.pnucene.2014.11.01010.1016/j.pnucene.2014.11.010 ↗
5. Hänninen · 2015 · 79
6. Yin · 2014 · 105
7. 10.1016/j.matchar.2024.11377610.1016/j.matchar.2024.113776 ↗
8. Bang · 2007 · 269
9. 10.1016/0921-5093(95)09991-310.1016/0921-5093(95)09991-3 ↗
10. 10.1007/s11661-006-1040-810.1007/s11661-006-1040-8 ↗
11. 10.3365/kjmm.2023.61.6.38910.3365/kjmm.2023.61.6.389 ↗
12. 10.3365/kjmm.2019.57.7.42210.3365/kjmm.2019.57.7.422 ↗
13. 10.3365/kjmm.2022.60.2.10210.3365/kjmm.2022.60.2.102 ↗
14. Di Schino · 2003 · 1830
15. 10.1016/s1006-706x(09)60011-x10.1016/s1006-706x(09)60011-x ↗
16. 10.1007/bf0265839310.1007/bf02658393 ↗
17. Park · 2023 · 413
18. Lee · 2017 · 870
19. 10.1016/0026-0800(76)90008-210.1016/0026-0800(76)90008-2 ↗
20. 10.1016/s0364-5916(02)00037-810.1016/s0364-5916(02)00037-8 ↗
21. Kozeschnik · 2001 · 349
22. 10.1016/j.actamat.2010.05.04310.1016/j.actamat.2010.05.043 ↗
23. 10.1179/02670830110150897210.1179/026708301101508972 ↗
24. Park · 2017 · 470
25. 10.1016/j.ijplas.2024.10414410.1016/j.ijplas.2024.104144 ↗
26. 10.1016/j.actamat.2015.02.00810.1016/j.actamat.2015.02.008 ↗
27. 10.1016/j.matlet.2022.13350210.1016/j.matlet.2022.133502 ↗