journal article·2026-01-10Open access

Effect of Design Parameters on Flow Characteristics in Powder Supply System for Micropropulsion Systems

Masaya Murohara, Marius C. Banica, Hiroyuki Koizumi, Matteo Madi

KONA Powder and Particle Journal· Volume 43· Issue 0

Abstract

Aluminum powder is an attractive fuel, especially for micropropulsion, due to its wide availability, high volumetric and gravimetric energy densities, and environmental friendliness. For safety reasons, the powder is preferably stored and supplied to a combustion chamber separately from the oxidizer. However, powder supply systems for micropropulsion applications are technologically immature. To improve this situation, a powder supply system was developed, and the impacts of important design factors on the supply characteristics were studied. This included operating modes, carrier gas pressures, gas line conductances, and powder line lengths. The results showed that, when compared to continuous operation, pulsed operation achieved 1) significantly higher powder flow rates and 2) significantly higher ratios of powder to carrier gas mass flow rates, ϕ. Furthermore, higher carrier gas pressures can increase the powder mass flow rates, but this reduces ϕ. The gas line conductance had a lesser impact on the powder flow rates than the pressure, but increasing the former also increased the powder flow rates without significant impact on ϕ. The powder line length had a negative impact on the powder flow rate, but no significant impact on ϕ. These results will help the future development of micropropulsion systems that use powder fuels.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Rocket and propulsion systems research · Electrohydrodynamics and Fluid Dynamics · Advanced Battery Technologies Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute of Energy Systems and Fluid-Engineering, Zurich University of Applied Sciences, Switzerland

Sirin Orbital Systems AG, Switzerland

Department of Advanced Energy, The University of Tokyo, Japan

Funding

European Space Agency · Japan Society for the Promotion of Science

References (22)

Show source-provided references
1. Besenhard M.O., Fathollahi S., Siegmann E., Slama E., Faulhammer E., Khinast J.G., Micro-feeding and dosing of powders via a small-scale powder pump, International Journal of Pharmaceutics, 519 (2017) 314–322. https://doi.org/10.1016/j.ijpharm.2016.12.02910.1016/j.ijpharm.2016.12.029 ↗
2. Cocco R., Chew J.W., 50 years of Geldart classification, Powder Technology, 428 (2023) 118861. https://doi.org/10.1016/j.powtec.2023.11886110.1016/j.powtec.2023.118861 ↗
3. David A.O., Knoll A.K., Experimental demonstration of an aluminum-fueled propulsion system for CubeSat applications, Journal of Propulsion and Power, 33 (2017) 1320–1324. https://doi.org/10.2514/1.B3633010.2514/1.B36330 ↗
4. Foote J.P., Thompson B.R., Lineberry J.T., Combustion of aluminum with steam for underwater propulsion, in: Gabriel D. Roy (Ed.), Advances in Chemical Propulsion: Science to Technology, CRC Press LLC, New York, 2001, pp. 133–145, ISBN: 9780429128820. https://doi.org/10.1201/978142004068510.1201/9781420040685.ch8 ↗
5. Geldart D., Types of gas fluidization, Powder Technology, 7 (1973) 285–292. https://doi.org/10.1016/0032-5910(73)80037-310.1016/0032-5910(73)80037-3 ↗
6. JIS B2005-1, Industrial-process control valves - part 1: control valve terminology and general considerations, Japanese Standards Association, 2004.
7. Li C., Zhu X., Deng Z., Yang J., Hu C., Wei J., Powder feeding in a powder engine under different gas-solid ratios, Acta Astronautica, 189 (2021) 712–721. https://doi.org/10.1016/j.actaastro.2021.08.02210.1016/j.actaastro.2021.08.022 ↗
8. Miller T.F., Herr J., Green rocket propulsion by reaction of Al and Mg powders and water, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, American Institute of Aeronautics and Astronautics, 2004. https://doi.org/10.2514/6.2004-403710.2514/6.2004-4037 ↗
9. Miller T.F., Walter J.L., Kiely D.H., A next-generation AUV energy system based on aluminum-seawater combustion, in: Proceedings of the 2002 Workshop on Autonomous Underwater Vehicles, presented at the Symposium on Autonomous Underwater Vehicle Technology (AUV), IEEE, 2002, pp. 111–119.10.1109/AUV.2002.1177213 ↗
10. Morikawa Y., Progress of technology in powder transportation: pneumatic and hydraulic conveying, Tetsu-to-Hagane, 77 (1991) 480–489. https://doi.org/10.2355/tetsutohagane1955.77.4_48010.2355/tetsutohagane1955.77.4_480 ↗
11. Murohara M., Koizumi H., Zhang R., Nishii K., Komurasaki K., Experimental study on combustion of water vapor and aluminum powder for chemical micropropulsion, Transactions of the Japan Society for Aeronautical and Space Sciences, 67 (2024) 86–98. https://doi.org/10.2322/tjsass.67.8610.2322/tjsass.67.86 ↗
12. Nishii K., Koizumi H., Temperature measurement on condensed combustion products of magnesium with oxygen and water vapor, Combustion and Flame, 262 (2024) 113362. https://doi.org/10.1016/j.combustflame.2024.11336210.1016/j.combustflame.2024.113362 ↗
13. Ogata K., A review: recent progress on evaluation of flowability and floodability of powder, KONA Powder and Particle Journal, 36 (2019) 33–49. https://doi.org/10.14356/kona.201900210.14356/kona.2019002 ↗
14. Ogata K., Ariga D., Evaluation of flowability for granulated powder using a test of powder discharge by pressurized air, EPJ Web of Conferences, 249 (2021) 08001. https://doi.org/10.1051/epjconf/20212490800110.1051/epjconf/202124908001 ↗
15. Oh K.W., Rong R., Ahn C.H., Miniaturization of pinch-type valves and pumps for practical micro total analysis system integration, Journal of Micromechanics and Microengineering, 15 (2005) 2449. https://doi.org/10.1088/0960-1317/15/12/02910.1088/0960-1317/15/12/029 ↗
16. Qian G.-H., Bágyi I., Burdick I.W., Pfeffer R., Shaw H., Stevens J.G., Gas–solid fluidization in a centrifugal field, AIChE Journal, 47 (2001) 1022–1034. https://doi.org/10.1002/aic.69047050910.1002/aic.690470509 ↗
17. Risha G.A., Connell T.L., Yetter R.A., Sundaram D.S., Yang V., Combustion of frozen nanoaluminum and water mixtures, Journal of Propulsion and Power, 30 (2014) 133–142. https://doi.org/10.2514/1.B3478310.2514/1.B34783 ↗
18. Ruiz-Carcel C., Starr A., Nsugbe E., Estimation of powder mass flow rate in a screw feeder using acoustic emissions, Powder Technology, 336 (2018) 122–130. https://doi.org/10.1016/j.powtec.2018.05.02910.1016/j.powtec.2018.05.029 ↗
19. Sun H., Hu C., Zhang T., Deng Z., Experimental investigation on mass flow rate measurements and feeding characteristics of powder at high pressure, Applied Thermal Engineering, 102 (2016) 30–37. https://doi.org/10.1016/j.applthermaleng.2016.03.14210.1016/j.applthermaleng.2016.03.142 ↗
20. Sundaram D.S., Yang V., Zarko V.E., Combustion of nano aluminum particles (Review), Combustion, Explosion, and Shock Waves, 51 (2015) 173–196. https://doi.org/10.1134/S001050821502004510.1134/S0010508215020045 ↗
21. Wollmark S., Yavor Y., Burning rates of nanoaluminum–water solid propellants at various pressures, Journal of Propulsion and Power, 35 (2019) 173–181. https://doi.org/10.2514/1.B3709810.2514/1.B37098 ↗
22. Xu H., Gao J., Zhong W., Zhu H., Experimental study on the fluidization discharging characteristics of Geldart-C kaolin powders in a blow tank with pulsed gas, Advanced Powder Technology, 33 (2022) 103372. https://doi.org/10.1016/j.apt.2021.11.02410.1016/j.apt.2021.11.024 ↗