Feasibility of Relationships between Tablet Physical Quality Parameters and Mechanical Properties of Dry Powder Formulation
Source abstract
Abstract
Compaction is a key unit operation in many particulate industries. Accordingly, this study addresses a research question of considerable importance concerning compact (or tablet) formation, i.e., the feasibility of using mechanical properties of powder formulations in low to medium pressure regime (<10 MPa) as predictors of tablet (i.e., compact) quality parameters. For the feasibility study, mechanical properties, i.e., elastic and elastoplastic, of dry powder formulations at three binder contents were determined using a flexible boundary cubical triaxial tester in low to medium pressure regime. For the same formulations, tablets formed at two pressing pressures (70 and 90 MPa) were tested for four physical quality parameters, i.e., diametral strength, axial penetration strength, indentation hardness, and friability. Some of the key findings were: bulk modulus increased with pressure and binder; shear modulus increased with confining pressure; tablet hardness increased with binder content upto a point and thereafter decreased or remained constant. All the powders' properties related with tablet qualities, i.e., had R2>0.80; i.e., demonstrating the feasibility of using powder properties as initial predictors of tablet quality for formulations tested. In particular, the spring-back index, compression index, and bulk modulus were found to be most correlated with tablets' diametral strength, axial penetration strength, indentation hardness, and friability. An elastic energy based hypothesis was proposed to provide a fundamental basis for mechanical properties of powder formulations vs. tablet quality relationships. The positive outcome of this feasibility study suggests that the approach could be used for other similar powder formulations.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Drug Solubulity and Delivery Systems · Powder Metallurgy Techniques and Materials · Granular flow and fluidized beds
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Food Science, The Pennsylvania State University
Department of Agricultural and Biological Engineering, The Pennsylvania State University
References (14)
Show source-provided references
1. Ameye, D., Keleb, E., Vervaet, C., Remon, J. P., Adams, E. and Massart, D. L. (2002): Scaling-up of a lactose wet granulation process in Mi-Pro high shear mixers, European J. of Pharmaceutics and Biopharmaceutics, 17, pp.247–251.10.1016/S0928-0987(02)00218-X ↗
2. German, R. M. (1994): “Powder metallurgy science”, 2nd Edition. Princeton, NJ: Metal Powder Industries Federation, 279 p.
3. Kamath, S. and Puri, V. M. (1997): Measurement of powder flow constitutive model parameters using a cubicle triaxial tester, Powder Technology, 90, pp.59–70.10.1016/S0032-5910(96)03200-7 ↗
4. Kuentz, M. and Leuenberger, H. (2000): A new approach to tablet strength of a binary mixture consisting of well and a poorly compactable substance, European Journal of Pharmaceutics and Biopharmaceutics, 49, pp.151–159.10.1016/S0939-6411(99)00078-8 ↗
5. Li, F. and Puri, V. M. (1997): “Development, testing, and verification of a medium pressure flexible boundary cubical triaxial tester” ASAE Paper No. 97-4104, American Society of Agricultural Engineers (ASAE), St. Joseph, MI, 12 p.
6. Leuenberge, H. and Rohere, B. D. (1986): Fundamentals of powder compression. I. The compactibility and compressibility of pharmaceutical powders, Pharmaceutical Research, 3, pp.12 – 22.10.1023/A:1016364613722 ↗
7. Mittal, B. and Puri, V. M. (2005): Rate-dependent elasto-viscoplastic constitutive model for industrial powders. Part 1: Parameter quantification, Particulate Science and Technology 23, pp.249–264.10.1080/02726350590955895 ↗
8. Pandeya, A. (2009): “Relating mechanical properties of dry and granulated pharmaceutical powder formulations with tablet quality parameters” PhD Dissertation, The Pennsylvania State University, University Park, PA, 313 p.
9. Pandeya, A. and Puri, V. M. (2008): “Comparison between mechanical properties of dry blended and granulated pharmaceutical powder formulations”, ASABE Technical Paper No. 083540, American Society of Agricultural and Biological Engineers (ASABE), St. Joseph, MI, 22 p.
10. Pandeya, A. and Puri, V. M. (2011): Rate-dependent mechanical properties of dry blended pharmaceutical powder formulations for tabletting applications, Powder Technology, 207, pp.26–34.10.1016/j.powtec.2010.10.006 ↗
11. Riippi, M., Antikainen, O., Niskanen, T. and Yliruusi, J. (1998): The effect of compression force on surface structure, crushing strength, friability and disintegration time of erythromycin acistrate tablets, European J. of Pharmaceutics and Biopharmaceutics, 46, pp.339–345.10.1016/S0939-6411(98)00043-5 ↗
12. Tabor, D. (2000): “The Hardness of metals”, Oxford University Press, London, 175 p.10.1093/oso/9780198507765.001.0001 ↗
13. Tye, C. K., Sun, C. and Amidon, G. E. (2005): Evaluation of the effects of tableting speed on the relationships between compaction pressures, tablet tensile strength, and tablet solid fraction, Journal of Pharmaceutical Sciences, 94, pp.465–472.10.1002/jps.20262 ↗
14. Wu, C. Y., Best, S. M., Bentham, A. C., Hancock, B. C. and Bonfield, W. (2005): A simple predictive model for the tensile strength of binary tablets, European Journal of Pharmaceutical Sciences, 25, pp.331–336.10.1016/j.ejps.2005.03.004 ↗