journal article·2019-01-10Open access

Micromechanical Characterization of Particle-Particle Bond in Biomass Assemblies Formed at Different Applied Pressure and Temperature

Apoorva Karamchandani, Hojae Yi, Virendra M. Puri

KONA Powder and Particle Journal· Volume 36· Issue 0

Abstract

During biomass pelletization, the presence of activated natural binders is thought to promote the formation of solid bridges in a biomass assembly. To examine this hypothesis, bonded particles were extracted from the switchgrass compacts formed at different pressure and temperature. This study investigated the influence of these two factors on the resistance to dislocation of the particle-particle bond. The generated force-bond dislocation curves were used to calculate the slope from no load to failure from the assemblies formed at the treatments A (60 MPa and 75 °C), B (100 MPa at 75 °C), C (60 MPa and 90 °C), and D (100 MPa at 90 °C). Assemblies from the treatment B had the highest diametral tensile strength (60.9 ± 7.1 kPa) and densities (653.2 kg m−3), whereas, assemblies formed from the treatment C had the lowest diametral strength (7.2 ± 1.4 kPa). The resistance to dislocation of particle-particle bonds at microscale was linearly correlated to the strength (R2=0.838) and density (R2=0.981) of the densified assemblies. High pressures are documented to form stronger compacts. However, the presence of sufficient moisture at low temperature can significantly improve the densified assembly properties by lowering the glass transition temperature of lignin to form stronger bonds.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Natural Fiber Reinforced Composites · Forest Biomass Utilization and Management · Thermochemical Biomass Conversion Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Agricultural and Biological Engineering, The Pennsylvania State University, USA

References (38)

Show source-provided references
1. Adapa P., Schoenau G., Tabil L., Sokhansanj S., Singh A., Compression of fractionated sun-cured and dehydrated alfalfa chops into cubes—specific energy models, Bioresource Technology, 98 (2007) 38–45. DOI: 10.1016/j.biortech.2005.11.03210.1016/j.biortech.2005.11.032 ↗
2. Adapa P., Tabil L., Schoenau G., Compaction characteristics of barley, canola, oat and wheat straw, Biosystems Engineering, 104 (2009) 335–344. DOI: 10.1016/j.biosystemseng.2009.06.02210.1016/j.biosystemseng.2009.06.022 ↗
3. Carroll J.P., Finnan J., Physical and chemical properties of pellets from energy crops and cereal straws, Biostystems Engineering, 112 (2012) 151–159. DOI: 10.1016/j.biosystemseng.2012.03.01210.1016/j.biosystemseng.2012.03.012 ↗
4. Colley Z., Fasina O.O., Bransby D., Lee Y.Y., Moisture effect on the physical characteristics of switchgrass pellets, Transactions of the ASABE, 49 (2006) 1845–1852.10.13031/2013.22271 ↗
5. Gilbert P., Ryu C., Sharifi V., Swithenbank J., Effect of process parameters on pelletisation of herbaceous crops, Fuel, 88 (2009) 1491–1497. DOI: 10.1016/j.fuel.2009.03.01510.1016/j.fuel.2009.03.015 ↗
6. Guigo N., Mija A., Vincent L., Sbirrazzuoli N., Rodríguez F., Nadif A., Dam J.E.G. van, Molecular mobility and relaxation process of isolated lignin studied by multifrequency calorimetric experiments, Physical Chemistry Chemical Physics, 11 (2009) 1227. DOI: 10.1039/b812512k10.1039/b812512k ↗
7. Han J.H., Saif M.T.A., In situ microtensile stage for electromechanical characterization of nanoscale freestanding films, Review of Scientific Instruments, 77 (2006) 45102. DOI: 10.1063/1.218836810.1063/1.2188368 ↗
8. Irvine G.M., The significance of the glass transition of lignin in thermomechanical pulping, Wood Science and Technology, 19 (1985) 139–149. DOI: 10.1007/BF0035307410.1007/BF00353074 ↗
9. Kaliyan N., Morey R.V., Factors affecting strength and durability of densified products, 2006 ASABE Annual Meeting, (2006) 066077. DOI: 10.13031/2013.2175410.13031/2013.21754 ↗
10. Kaliyan N., Morey R.V, Densification characteristics of corn stover and switchgrass, Transactions of the ASABE, 52 (2009a) 907–920.10.13031/2013.27380 ↗
11. Kaliyan N., Morey V.R., Factors affecting strength and durability of densified biomass products, Biomass and Bioenergy, 33 (2009b) 337–359. DOI: 10.1016/j.biombioe.2008.08.00510.1016/j.biombioe.2008.08.005 ↗
12. Kaliyan N., Morey V.R., Natural binders and solid bridge type binding mechanisms in briquettes and pellets made from corn stover and switchgrass, Bioresource Technology, 101 (2010) 1082–1090. DOI: 10.1016/j.biortech.2009.08.06410.1016/j.biortech.2009.08.064 ↗
13. Karamchandani A., Predictive relationships for quality assessment of densified biomass using fundamental mechanical properties of ground corn stover, switchgrass, and willow (Master of Science Dissertation), Pennsylvania State University, 2013.
14. Karamchandani A., Yi H., Puri V.M., Comparison of mechanical properties of ground corn stover, switchgrass, and willow and their pellet qualities, Particulate Science and Technology, 36 (2018) 447–456. DOI: 10.1080/02726351.2017.135586010.1080/02726351.2017.1355860 ↗
15. Karamchandani A., Yi H., Puri V.M., Fundamental mechanical properties of ground switchgrass for quality assessment of pellets, Powder Technology, 283 (2015) 48–56. DOI:10.1016/j.powtec.2015.04.06910.1016/j.powtec.2015.04.069 ↗
16. Karamchandani A., Yi H., Puri V.M., Comparison and explanation of predictive capability of pellet quality metrics based on fundamental mechanical properties of ground willow and switchgrass, Advanced Powder Technology, 27 (2016a) 1411–1417. DOI: 10.1016/j.apt.2016.04.03610.1016/j.apt.2016.04.036 ↗
17. Karamchandani A., Yi H., Puri V.M., Single particle mechanical characterization of ground switchgrass in air dry and wet states using a microextensometer, Powder Technology, 301 (2016b) 568–574.10.1016/j.powtec.2016.06.041 ↗
18. Lee S.M., Ahn B.J., Choi D.H., Han G.S., Jeong H.S., Ahn S.H., Yang I., Effects of densification variables on the durability of wood pellets fabricated with Larix kaempferi C. and Liriodendron tulipifera L. sawdust, Biomass and Bioenergy, 48 (2013) 1–9. DOI: 10.1016/j.biombioe.2012.10.01510.1016/j.biombioe.2012.10.015 ↗
19. MacBain R., Pelleting Animal Feed, American Feed Manufacturers Associations, (1966).
20. Mani S, Tabil L.G., Sokhansanj S., An overview of compaction of biomass grinds, Powder Handling and Processing, 15 (2003) 160–168.
21. Mani S., Tabil L.G., Sokhansanj S., Grinding performance and physical properties of wheat and barley straws, corn stover and switchgrass, Biomass and Bioenergy, 27 (2004) 339–352. DOI: 10.1016/j.biombioe.2004.03.00710.1016/j.biombioe.2004.03.007 ↗
22. Mani S., Tabil L.G., Sokhansanj S., Effects of compressive force, particle size and moisture content on mechanical properties of biomass pellets from grasses, Biomass and Bioenergy, 30 (2006) 648–654. DOI: 10.1016/j.biombioe.2005.01.00410.1016/j.biombioe.2005.01.004 ↗
23. Pantano M.F., Espinosa H.D., Pagnotta L., Mechanical characterization of materials at small length scales, Journal of Mechanical Science, 26 (2012) 545–561. DOI: 10.1007/s12206-011-1214-1.10.1007/s12206-011-1214-1 ↗
24. Parrish D.J., Fike J.H., The biology and agronomy of switchgrass for biofuels, Critical Reviews in Plant Sciences, 24 (2005) 423–459. DOI: 10.1080/07352680500316433.10.1080/07352680500316433 ↗
25. Payne J.D., Improving quality of pellet feeds, Milling Feed and Fertilizer, 161 (1978) 34–41.
26. Poddar S., Kamruzzaman M., Sujan S.M.A., Hossain M., Jamal M.S., Gafur M.A., Khanam M., Effect of compression pressure on lignocellulosic biomass pellet to improve fuel properties: Higher heating value, Fuel, 131 (2014) 43–48. DOI: 10.1016/j.fuel.2014.04.06110.1016/j.fuel.2014.04.061 ↗
27. Rhén C., Gref R., Sjöström M., Wästerlund I., Effects of raw material moisture content, densification pressure and temperature on some properties of Norway spruce pellets, Fuel Processing Technology, 87 (2005) 11–16. DOI: 10.1016/j.fuproc.2005.03.00310.1016/j.fuproc.2005.03.003 ↗
28. Sanderson M.A., Adler P.R., Boateng A.A., Casler M.D., Sarath G., Switchgrass as a biofuels feedstock in the USA, Canadian Journal of Plant Science, 86 (2006) 1315–1325. DOI: 10.4141/P06-136.10.4141/P06-136 ↗
29. Shaw M.D., Tabil L.G., Compression and relaxation characteristics of selected biomass `grinds, 2007 ASAE Annual Meeting, (2007) 076183. DOI: 10.13031/2013.2351110.13031/2013.23511 ↗
30. Stelte W., Holm J.K., Sanadi A.R., Barsberg S., Ahrenfeldt J., Henriksen U.B., A study of bonding and failure mechanisms in fuel pellets from different biomass resources, Biomass and Bioenergy, 35 (2011) 910–918. DOI: 10.1016/j.biombioe.2010.11.00310.1016/j.biombioe.2010.11.003 ↗
31. Stelte W., Sanadi A.R., Shang L., Holm J.K., Ahrenfeldt J., Henriksen U.B., Recent developments in biomass pelletization—a review, BioResources, 7 (2012) 4451–4490.10.15376/biores.7.3.Stelte ↗
32. Tumuluru J.S., Effect of process variables on the density and durability of the pellets made from high moisture corn stover, Biostystems Engineering, 119 (2014) 44–57. DOI: 10.1016/j.biosystemseng.2013.11.01210.1016/j.biosystemseng.2013.11.012 ↗
33. Tumuluru J.S., Wright C.T., Hess J.R., Kenney K.L., National I., A review of biomass densification systems to develop uniform feedstock commodities for bioenergy application, Biofuels, Bioproducts and Biorefining, (2011) 683–707. DOI: 10.1002/bbb10.1002/bbb.324 ↗
34. Tumuluru J.S., Wright C.T., Kenny K.L., Hess J. R., A review on biomass densification technologies for energy application, Idaho National Laboratory (INL), (2010) INL/EXT-10-18420. DOI: 10.2172/101619610.2172/1016196 ↗
35. U.S. Department of Energy, 2016 Billion-Ton Report: Advancing Domestic Resources for a Thriving Bioeconomy, Volume 1: Economic Availability of Feedstocks, Oak Ridge, 2016.
36. Yi H., Pandeya A., Karamchandani A., Puri V.M., Critical review on engineering mechanical quality of green compacts using powder properties, KONA Powder and Particle Journal, 35 (2018) 32–48. DOI: 10.14356/kona.201800610.14356/kona.2018006 ↗
37. Zamil M.S., Yi H., Puri V.M., Mechanical characterization of outer epidermal middle lamella of onion under tensile loading, American Journal of Botany, 101 (2014) 778–787. DOI: 10.3732/ajb.130041610.3732/ajb.1300416 ↗
38. Zamil M.S., Yi H., Puri V.M., The mechanical properties of plant cell walls soft material at the subcellular scale: the implications of water and of the intercellular boundaries, Journal of Materials Science, 50 (2015) 6608–6623. DOI: 10.1007/s10853-015-9204-910.1007/s10853-015-9204-9 ↗