journal article·2022-01-10Open access

Correlating Granule Surface Structure Morphology and Process Conditions in Fluidized Bed Layering Spray Granulation

Maike Orth, Paul Kieckhefen, Swantje Pietsch, Stefan Heinrich

KONA Powder and Particle Journal· Volume 39· Issue 0

Abstract

A workflow for developing a multidimensional, linear correlation between the process conditions during fluidized bed spray granulation and the surface morphology of the resulting granules is presented. Spray coating experiments with Cellets®500 particles and sodium benzoate solution were performed in a lab-scale fluidized bed varying liquid spray rate, fluidization air flow rate, fluidization air temperature, spray air temperature and spray atomization pressure. To characterize the surface structure, the surface roughness of the coated particles was quantified using confocal laser-scanning microscopy. The roughness was correlated to the process conditions, and the resulting correlation was rigorously analyzed for the importance and co-linearities of the individual process parameters using a principal component analysis. The surface roughness is strongly dependent on the spray rate of the coating solution, the fluidization air temperature and the atomization pressure at the nozzle. In general, wet process conditions and large droplets with a low initial velocity favor the formation of particles with a rough surface structure, while dry conditions and fine droplets with a high velocity result in granules with a smooth and compact coating layer.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Granular flow and fluidized beds · Microencapsulation and Drying Processes · Fluid Dynamics and Heat Transfer

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institue of Solids Process Engineering and Particle Technology, Hamburg University of Technology, Germany

Funding

Deutsche Forschungsgemeinschaft · BASF SE

References (18)

Show source-provided references
1. Depypere F., Van Oostveldt P., Pieters J.G., Dewettinck K., Quantification of microparticle coating quality by confocal laser scanning microscopy (CLSM), European Journal of Pharmaceutics and Biopharmaceutics, 73 (2009) 179–186. DOI: 10.1016/j.ejpb.2009.04.00710.1016/j.ejpb.2009.04.007 ↗
2. DIN EN ISO 4287:2010-07, Geometrical Product Specifications (GPS)—Surface Texture: Profile Method—Terms, Definitions and Surface Texture Parameters, DIN (Deutsches Institut für Normung e.V.), Berlin, 2010.
3. DIN EN ISO 25178-2:2012 Geometrical Product Specifications (GPS)—Surface Texture: Areal—Part 2: Terms, Definitions and Surface Texture Parameters, DIN (Deutsches Institut für Normung e.V.), Berlin, 2012.
4. Dewettinck K., Huyghebaert A., Fluidized bed coating in food technology, Trends in Food Science & Technology, 10 (1999) 163–168. DOI: 10.1016/S0924-2244(99)00041-210.1016/S0924-2244(99)00041-2 ↗
5. Diez E., Kieckhefen P., Meyer K., Bück A., Tsotsas E., Heinrich S., Particle dynamics in a multi-staged fluidized bed: particle transport behavior on micro-scale by discrete particle modelling, Advanced Powder Technology, 10 (2019) 2014–2031. DOI: 10.1016/j.apt.2019.05.02510.1016/j.apt.2019.05.025 ↗
6. Diez E., Meyer K., Bück A., Tsotsas E., Heinrich S., Influence of process conditions on the product properties in a continuous fluidized bed spray granulation process, Chemical Engineering Research and Design, 139 (2018) 104–115. DOI: 10.1016/j.cherd.2018.09.03210.1016/j.cherd.2018.09.032 ↗
7. Fries L., Discrete particle modeling of a fluidized bed granulator (Dissertation), Cuvillier Verlag, 2012. ISBN: 9783954042456.
8. Hampel N.A., Diskontinuierliches und kontinuierliches Pelletcoating im Wurster-Wirbelschichtprozess (Dissertation), Otto-von-Guericke-Universität Magdeburg, 2015. http://dx.doi.org/10.25673/4340
9. Hoffmann T., Rieck C., Bück A., Peglow M., Tsotsas E., Influence of granule porosity during fluidized bed spray granulation, Procedia Engineering, 102 (2015) 458–467. DOI: 10.1016/j.proeng.2015.01.18910.1016/j.proeng.2015.01.189 ↗
10. Keyence, 3D Laser Scanning Confocal Microscope VK-X250K/X260K, VK-X150K/X160K, VK-X120K/X130K: User’s Manual, 2015.
11. Kieckhefen P., Pietsch S., Dosta M., Heinrich S., Possibilities and limits of computational fluid dynamics-discrete element method simulations in process engineering: a review of recent advancements and future trends, Annual review of chemical and biomolecular engineering, 11 (2020) 397–422. DOI: 10.1146/annurev-chembioeng-110519-07541410.1146/annurev-chembioeng-110519-075414 ↗
12. Perfetti G., Van de Casteele E., Rieger B., Wildeboer W.J., Meesters G.M.H., X-ray micro tomography and image analysis as complementary methods for morphological characterization and coating thickness measurement of coated particles, Advanced Powder Technology, 21 (2010) 663–675. DOI: 10.1016/j.apt.2010.08.00210.1016/j.apt.2010.08.002 ↗
13. Pietsch S., Kieckhefen P., Heinrich S., Müller M., Schönherr M., Kleine Jäger F., CFD-DEM modelling of circulation frequencies and residence times in a prismatic spouted bed, Chemical Engineering Research and Design, 132 (2018) 1105–1116. DOI: 10.1016/j.cherd.2018.01.01310.1016/j.cherd.2018.01.013 ↗
14. Rieck C., Hoffmann T., Bück A., Peglow M., Tsotsas E., Influence of drying conditions on layer porosity in fluidized bed spray granulation, Powder Technology, 272 (2015) 120–131. DOI: 10.1016/j.powtec.2014.11.01910.1016/j.powtec.2014.11.019 ↗
15. Schmidt M., Bück A., Tsotsas E., Shell porosity in spray fluidized bed coating with suspensions, Advanced Powder Technology, 28 (2017) 2921–2928. DOI: 10.1016/j.apt.2017.08.02010.1016/j.apt.2017.08.020 ↗
16. Turton R., Challenges in the modeling and prediction of coating of pharmaceutical dosage forms, Powder Technology, 181 (2008) 186–194. DOI: 10.1016/j.powtec.2006.12.00610.1016/j.powtec.2006.12.006 ↗
17. Tzika M., Alexandridou S., Kiparissides C., Evaluation of the morphological and release characteristics of coated fertilizer granules produced in a Wurster fluidized bed, Powder Technology, 132 (2003) 16–24. DOI: 10.1016/S0032-5910(02)00345-510.1016/S0032-5910(02)00345-5 ↗
18. Werner S.R.L., Jones J.R., Paterson A.H.J., Archer R.H., Pearce D.L., Air-suspension particle coating in the food industry: Part I—state of the art, Powder Technology, 171 (2007) 25–33. DOI: 10.1016/j.powtec.2006.08.01410.1016/j.powtec.2006.08.014 ↗