journal article·2026-01-10Open access

Effect of Temperature on Aluminium Powder Flowability and Spreadability

Mozhdeh Mehrabi, Fatemeh Ali Akbar Talebi, Nathan Berry, Sorush Khajepor, Sina Haeri, Jabbar Gardy, Joseph Oluleke, Andrew Bayly, Ali Hassanpour

KONA Powder and Particle Journal· Volume 43· Issue 0

Abstract

In powder-based Additive Manufacturing (AM) the precise control of process parameters plays a significant role in the quality and efficiency of the printing process. Among these, the effect of temperature has received less attention in the literature, although it is a significant factor that influences the inter-particle forces and, consequently the powder flow and spreading behaviour of powders. In selective laser sintering (SLS) or selective laser melting (SLM), pre-heating the chamber and powder bed is a required step prior to sintering, hence, the temperature can significantly influence the layer adhesion and spread quality. In this context, the present study explores the effect of elevated temperature on the flow and spreading behaviours of AlSi10Mg powders. The flow properties of two different grades of aluminium alloy powders are characterised using the Carney and Hall flow tests, angle of repose and shear test techniques at different temperatures and correlated with the spreading behaviour at elevated temperatures, measured using the spreading rig with a heated bed developed at the University of Leeds. This study revealed that at elevated temperatures the spreadability of AlSi10Mg powders worsens because of changes in interparticle forces and particle surface interactions.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Powder Metallurgy Techniques and Materials · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Chemical and Process Engineering, University of Leeds, UK

School of Engineering, University of Edinburgh, UK

Cormica Limited, UK

Carpenter Additive, UK

Funding

Engineering and Physical Sciences Research Council · University of Leeds Impact Acceleration Account

References (54)

Show source-provided references
1. Ajabshir S.Z., Hare C., Sofia D., Barletta D., Poletto M., Investigating the effect of temperature on powder spreading behaviour in powder bed fusion additive manufacturing process by Discrete Element Method, Powder Technology, 436 (2024) 119468. https://doi.org/10.1016/j.powtec.2024.11946810.1016/j.powtec.2024.119468 ↗
2. ASTM 52900-15, Standard terminology for additive manufacturing—general principles—terminology, ASTM International, West Conshohocken, PA, 3 (2015) 5. https://doi.org/10.1520/ISOASTM52900-1510.1520/ISOASTM52900-15 ↗
3. ASTM B213-20, Standard test methods for flow rate of metal powders using the hall flowmeter funnel, ASTM International, (2020). https://doi.org/10.1520/B0213-2010.1520/B0213-20 ↗
4. Avrampos P., Vosniakos G.-C., A review of powder deposition in additive manufacturing by powder bed fusion, Journal of Manufacturing Processes, 74 (2022) 332–352. https://doi.org/10.1016/j.jmapro.2021.12.02110.1016/j.jmapro.2021.12.021 ↗
5. Bagga P., Brisson G., Baldwin A., Davies C.E., Stick-slip behavior of dairy powders: Temperature effects, Powder Technology, 223 (2012) 46–51. https://doi.org/10.1016/j.powtec.2011.05.01510.1016/j.powtec.2011.05.015 ↗
6. Balbaa M., Ghasemi A., Fereiduni E., Elbestawi M., Jadhav S., Kruth J.-P., Role of powder particle size on laser powder bed fusion processability of AlSi10mg alloy, Additive Manufacturing, 37 (2021) 101630. https://doi.org/10.1016/j.addma.2020.10163010.1016/j.addma.2020.101630 ↗
7. Carr R.L., Evaluating flow properties of solids, Chemical Engineering, 72 (1965) 163–168.
8. Chen B., Moon S.K., Yao X., Bi G., Shen J., Umeda J., Kondoh K., Comparison study on additive manufacturing (AM) and powder metallurgy (PM) AlSi10Mg alloys, JOM, 70 (2018) 644–649. https://doi.org/10.1007/s11837-018-2793-410.1007/s11837-018-2793-4 ↗
9. Clayton J., Millington-Smith D., Armstrong B., The application of powder rheology in additive manufacturing, JOM, 67 (2015) 544–548. https://doi.org/10.1007/s11837-015-1293-z10.1007/s11837-015-1293-z ↗
10. Cordova L., Campos M., Tinga T., Assessment of moisture content and its influence on laser beam melting feedstock, Euro PM 2017, (2017) 6pp.
11. Dowling L., Kennedy J., O’Shaughnessy S., Trimble D., A review of critical repeatability and reproducibility issues in powder bed fusion, Materials & Design, 186 (2020) 108346. https://doi.org/10.1016/j.matdes.2019.10834610.1016/j.matdes.2019.108346 ↗
12. Fouda Y.M., Bayly A.E., A DEM study of powder spreading in additive layer manufacturing, Granular Matter, 22 (2020) 10. https://doi.org/10.1007/s10035-019-0971-x10.1007/s10035-019-0971-x ↗
13. Freeman R., Measuring the flow properties of consolidated, conditioned and aerated powders—a comparative study using a powder rheometer and a rotational shear cell, Powder Technology, 174 (2007) 25–33. https://doi.org/10.1016/j.powtec.2006.10.01610.1016/j.powtec.2006.10.016 ↗
14. Ganesan V., Rosentrater K., Muthukumarappan K., Flowability and handling characteristics of bulk solids and powders–a review with implications for DDGS, Biosystems Engineering, 101 (2008) 425–435. https://doi.org/10.1016/j.biosystemseng.2008.09.00810.1016/j.biosystemseng.2008.09.008 ↗
15. Geldart D., Abdullah E., Verlinden A., Characterisation of dry powders, Powder Technology, 190 (2009) 70–74. https://doi.org/10.1016/j.powtec.2008.04.08910.1016/j.powtec.2008.04.089 ↗
16. Gibson I., Rosen D.W., Stucker B., Khorasani M., Rosen D., Stucker B., Khorasani M., Additive Manufacturing Technologies, Springer, 2021, ISBN: 9783030561260. https://doi.org/10.1007/978-3-030-56127-710.1007/978-3-030-56127-7 ↗
17. Grainger L., Investigating the effects of multiple re-use of Ti6Al4V powder in additive manufacturing (AM), Renishaw plc, (2016) 1–9.
18. Greenspan L., Humidity fixed points of binary saturated aqueous solutions, Journal of Research of the National Bureau of Standards Section A, Physics and Chemistry, 81 (1977) 89. https://doi.org/10.6028/jres.081A.01110.6028/jres.081A.011 ↗
19. Grubbs J., Sousa B.C., Cote D., Exploration of the effects of metallic powder handling and storage conditions on flowability and moisture content for additive manufacturing applications, Metals, 12 (2022) 603. https://doi.org/10.3390/met1204060310.3390/met12040603 ↗
20. Hausner H.H., Friction conditions in a mass of metal powder, Polytechnic Inst. of Brooklyn. Univ. of California, Los Angeles, 1967.
21. Haydari Z., Talebi F., Mehrabi M., Gardy J., Moeni M., Bayly A.E., Hassanpour A., Insights into the assessment of spreadability of stainless steel powders in additive manufacturing, Powder Technology, 439 (2024) 119667. https://doi.org/10.1016/j.powtec.2024.11966710.1016/j.powtec.2024.119667 ↗
22. He Y., Hassanpour A., Bayly A.E., Combined effect of particle size and surface cohesiveness on powder spreadability for additive manufacturing, Powder Technology, 392 (2021) 191–203. https://doi.org/10.1016/j.powtec.2021.06.04610.1016/j.powtec.2021.06.046 ↗
23. Hulme C.N., Mellin P., Marchetti L., Hari V., Uhlirsch M., Strandh E., Saeidi K., Dubiez-Le Goff S., Saleem S., Pettersson V., A practicable and reliable test for metal powder spreadability: Development of test and analysis technique, Progress in Additive Manufacturing, 8 (2023) 505–517. https://doi.org/10.1007/s40964-022-00341-310.1007/s40964-022-00341-3 ↗
24. Jacob G., Jacob G., Brown C.U., Donmez A., The influence of spreading metal powders with different particle size distributions on the powder bed density in laser-based powder bed fusion processes, US Department of Commerce, National Institute of Standards and Technology, 2018. https://doi.org/10.6028/NIST.AMS.100-1710.6028/NIST.AMS.100-17 ↗
25. Jenike A.W., A theory of flow of particulate solids in converging and diverging channels based on a conical yield function, Powder Technology, 50 (1987) 229–236. https://doi.org/10.1016/0032-5910(87)80068-210.1016/0032-5910(87)80068-2 ↗
26. LeBrun T., Standardization gaps in powder feedstock characterization and establishing acceptability for reuse in additive manufacturing, JOM, (2024) 1885–188. https://doi.org/10.1007/s11837-024-06385-w10.1007/s11837-024-06385-w ↗
27. Li C., Liu Z., Fang X., Guo Y., Residual stress in metal additive manufacturing, Procedia CIRP, 71 (2018) 348–353. https://doi.org/10.1016/j.procir.2018.05.03910.1016/j.procir.2018.05.039 ↗
28. Liu Q., Danlos Y., Song B., Zhang B., Yin S., Liao H., Effect of high-temperature preheating on the selective laser melting of yttria-stabilized zirconia ceramic, Journal of Materials Processing Technology, 222 (2015) 61–74. https://doi.org/10.1016/j.jmatprotec.2015.02.03610.1016/j.jmatprotec.2015.02.036 ↗
29. Liu Z., Huang C., Gao C., Liu R., Chen J., Xiao Z., Characterization of Ti6Al4V powders produced by different methods for selective electron beam melting, Journal of Mining and Metallurgy B: Metallurgy, 55 (2019) 121–128. https://doi.org/10.2298/JMMB181025008L10.2298/JMMB181025008L ↗
30. Machno M., Franczyk E., Bogucki R., Matras A., Zębala W., A comparative study on the structure and quality of SLM and cast AISI 316L samples subjected to WEDM processing, Materials, 15 (2022) 701. https://doi.org/10.3390/ma1503070110.3390/ma15030701 ↗
31. Mahamood R., Akinlabi E., Effect of powder flow rate on surface finish in laser additive manufacturing process, IOP Conference Series: Materials Science and Engineering, IOP Publishing, 391 (2018) 012005. https://doi.org/10.1088/1757-899X/391/1/01200510.1088/1757-899X/391/1/012005 ↗
32. Mehrabi M., Analysis of bulk behaviour of particles based on their individual properties, PhD thesis, University of Leeds, (2021). https://etheses.whiterose.ac.uk/29855/
33. Mehrabi M., Gardy J., Talebi F.A., Farshchi A., Hassanpour A., Bayly A.E., An investigation of the effect of powder flowability on the powder spreading in additive manufacturing, Powder Technology, 413 (2023) 117997. https://doi.org/10.1016/j.powtec.2022.11799710.1016/j.powtec.2022.117997 ↗
34. Mindt H., Megahed M., Lavery N., Holmes M., Brown S., Powder bed layer characteristics: The overseen first-order process input, Metallurgical and Materials Transactions A, 47 (2016) 3811–3822. https://doi.org/10.1007/s11661-016-3470-210.1007/s11661-016-3470-2 ↗
35. Murtaza H.A., Mukhangaliyeva A., Golman B., Perveen A., Talamona D., Quantitative characterization of metal powder morphology, size distribution, and flowability for additive manufacturing, Journal of Materials Engineering and Performance, 33 (2024) 10853–10867. https://doi.org/10.1007/s11665-023-08761-010.1007/s11665-023-08761-0 ↗
36. Oropeza D., Penny R.W., Gilbert D., Hart A.J., Mechanized spreading of ceramic powder layers for additive manufacturing characterized by transmission X-ray imaging: Influence of powder feedstock and spreading parameters on powder layer density, Powder Technology, 398 (2022) 117053. https://doi.org/10.1016/j.powtec.2021.11705310.1016/j.powtec.2021.117053 ↗
37. Papazoglou E.L., Karkalos N.E., Karmiris-Obratański P., Markopoulos A.P., On the modeling and simulation of SLM and SLS for metal and polymer powders: A review, Archives of Computational Methods in Engineering, (2022) 941–973. https://doi.org/10.1007/s11831-021-09601-x10.1007/s11831-021-09601-x ↗
38. Prashanth K., Scudino S., Eckert J., Defining the tensile properties of Al-12Si parts produced by selective laser melting, Acta Materialia, 126 (2017) 25–35. https://doi.org/10.1016/j.actamat.2016.12.04410.1016/j.actamat.2016.12.044 ↗
39. Reijonen J., Revuelta A., Metsä-Kortelainen S., Salminen A., Effect of hard and soft re-coater blade on porosity and processability of thin walls and overhangs in laser powder bed fusion additive manufacturing, The International Journal of Advanced Manufacturing Technology, (2023)2283–2296. https://doi.org/10.1007/s00170-023-12853-5
40. Riener K., Oswald S., Winkler M., Leichtfried G.J., Influence of storage conditions and reconditioning of AlSi10Mg powder on the quality of parts produced by laser powder bed fusion (LPBF), Additive Manufacturing, 39 (2021) 101896. https://doi.org/10.1016/j.addma.2021.10189610.1016/j.addma.2021.101896 ↗
41. Rüther M., Klippstein S.H., Ponusamy S., Rüther T., Schmid H.-J., Flowability of polymer powders at elevated temperatures for additive manufacturing, Powder Technology, 422 (2023) 118460. https://doi.org/10.1016/j.powtec.2023.11846010.1016/j.powtec.2023.118460 ↗
42. Santos Macías J.G., Douillard T., Zhao L., Maire E., Pyka G., Simar A., Influence on microstructure, strength and ductility of build platform temperature during laser powder bed fusion of AlSi10Mg, Acta Materialia, 201 (2020) 231–243. https://doi.org/10.1016/j.actamat.2020.10.00110.1016/j.actamat.2020.10.001 ↗
43. Schulze D., Time-and velocity-dependent properties of powders effecting slip-stick oscillations, Chemical Engineering & Technology: Industrial Chemistry-Plant Equipment-Process Engineering-Biotechnology, 26 (2003) 1047–1051. https://doi.org/10.1002/ceat.20030311210.1002/ceat.200303112 ↗
44. Shinohara K., Oida M., Golman B., Effect of particle shape on angle of internal friction by triaxial compression test, Powder Technology, 107 (2000) 131–136. https://doi.org/10.1016/S0032-5910(99)00179-510.1016/S0032-5910(99)00179-5 ↗
45. Snow Z., Martukanitz R., Joshi S., On the development of powder spreadability metrics and feedstock requirements for powder bed fusion additive manufacturing, Additive Manufacturing, 28 (2019) 78–86. https://doi.org/10.1016/j.addma.2019.04.01710.1016/j.addma.2019.04.017 ↗
46. Strondl A., Lyckfeldt O., Brodin H.K., Ackelid U., Characterization and control of powder properties for additive manufacturing, JOM, 67 (2015) 549–554. https://doi.org/10.1007/s11837-015-1304-010.1007/s11837-015-1304-0 ↗
47. Suryawanshi J., Prashanth K., Scudino S., Eckert J., Prakash O., Ramamurty U., Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting, Acta Materialia, 115 (2016) 285–294. https://doi.org/10.1016/j.actamat.2016.06.00910.1016/j.actamat.2016.06.009 ↗
48. Touzé S., Rauch M., Hascoët J.-Y., Flowability characterization and enhancement of aluminium powders for additive manufacturing, Additive Manufacturing, 36 (2020) 101462. https://doi.org/10.1016/j.addma.2020.10146210.1016/j.addma.2020.101462 ↗
49. Venturi F., Taylor R., Additive manufacturing in the context of repeatability and reliability, Journal of Materials Engineering and Performance, 32 (2023) 6589–6609. https://doi.org/10.1007/s11665-023-07897-310.1007/s11665-023-07897-3 ↗
50. Vock S., Klöden B., Kirchner A., Weißgärber T., Kieback B., Powders for powder bed fusion: A review, Progress in Additive Manufacturing, 4 (2019) 383–397. https://doi.org/10.1007/s40964-019-00078-610.1007/s40964-019-00078-6 ↗
51. Weiss C., Heslenfeld J., Saewe J.K., Bremen S., Häfner C.L., Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF), Procedia CIRP, 111 (2022) 115–120. https://doi.org/10.1016/j.procir.2022.08.10210.1016/j.procir.2022.08.102 ↗
52. Zafar U., Hare C., Hassanpour A., Ghadiri M., Drop test: A new method to measure the particle adhesion force, Powder Technology, 264 (2014) 236–241. https://doi.org/10.1016/j.powtec.2014.04.02210.1016/j.powtec.2014.04.022 ↗
53. Zhang J., Liu P., Powder flowability characterisation at preheating temperature in additive manufacturing, Powder Metallurgy, 66 (2023) 427–435. https://doi.org/10.1080/00325899.2023.222595310.1080/00325899.2023.2225953 ↗
54. Zinatlou Ajabshir S., Sofia D., Hare C., Barletta D., Poletto M., Experimental characterisation of the spreading of polymeric powders in powder bed fusion additive manufacturing process at changing temperature conditions, Advanced Powder Technology, 35 (2024) 104412. https://doi.org/10.1016/j.apt.2024.10441210.1016/j.apt.2024.104412 ↗