journal article·2010Open access

Development of Advanced Ceramics by Powder Composite Process

Junichi Tatami, Hiromi Nakano, Toru Wakihara, Katsutoshi Komeya

KONA Powder and Particle Journal· Volume 28· Issue 0

Abstract

A powder composite process was applied to develop several kinds of advanced ceramics. TiO2 nanoparticles and Si3N4 particles were mixed using a powder composite process to disperse TiN nanoparticles in Si3N4 ceramics, which are expected to be used as novel materials for next-generation hybrid ceramic bearings. TEM observations showed that the TiO2 nanoparticles were directly bonded to submicron Si3N4 particles. Si3N4 ceramics with uniformly-dispersed TiN nanoparticles were fabricated using the composite particles. The amount of damage caused by the Si3N4 ceramics with TiN nanoparticles to the mating metals in a ball-on-disk test was comparable to the damage caused by Si3N4 ceramics without TiN particles. Nanocomposite particles of Al2O3-doped ZnO prepared by a powder composite process were also used for fabricating ZnO ceramics. TEM observations revealed the uniform presence of Al2O3 nanoparticles on ZnO particles. A sintering body fabricated using the composite powder prepared by this powder composite process had more uniform and finer microstructures than that fabricated using a powder mixture prepared by conventional wet mixing. The ZnO ceramics prepared by the powder composite process exhibited higher electrical conductivity than those prepared by the conventional wet ball milling process. CNT-dispersed Al2O3 ceramics were fabricated using a powder mixture of CNT and fine Al2O3 powder prepared by the powder composite process. It was shown that CNTs were uniformly dispersed in the developed CNT-dispersed Al2O3 ceramics, and that they had high electrical conductivity and strength.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Metal and Thin Film Mechanics · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Graduate School of Environment and Information Sciences, Yokohama National University

Cooperative Research Facility Center, Toyohashi University of Technology

References (46)

Show source-provided references
1. 1) Naito, M., Kondo, A. and Yokoyama, T. (1993): Applications of Comminution Techniques for the Surface Modification of Powder Materials, ISIJ International, vol. 33, pp. 915–924.10.2355/isijinternational.33.915 ↗
2. 2) Hosokawa, M., Nogi, K., Naito, M. and Yokoyama, T. (2007): “Nanoparticle Technology Handbook,” Elsevier, Oxford, UK.
3. 3) Naito, M., Hotta, T., Asahi, S. and Tanimoto, T. (1998): Deposition of Fine Particles on Surface of Core Particles by High-Speed Elliptical Rotor-Type Mixer, Kagaku Kogaku Ronbunshu, vol. 24, pp. 52–56.10.1252/kakoronbunshu.24.52 ↗
4. 4) Naito, M., Hotta, T., Asahi, S., Tanimoto, T. and Endoh, S. (1998): Effect of Processing Conditions on Particle Composite Process by a High-Speed Elliptical-Rotor-Type Mixer, Kagaku Kogaku Ronbunshu, vol. 24, pp. 99–103.10.1252/kakoronbunshu.24.99 ↗
5. 5) Naito, M., Hotta, T., Tanimoto, T., Endoh, S. and Nogi, K. (2000): Effect of Fine Particle Size on Particle Composite Process by a High-Speed Elliptical-Rotor-Type Mixer, Kagaku Kogaku Ronbunshu, vol. 26, pp. 62–67.10.1252/kakoronbunshu.26.62 ↗
6. 6) Hotta, T., Naito, M. Szeplvolgyi, J., Endoh, S. and Nogi, K. (2001): Effect of Rotor Shape on Particle Composite Process by a High-Speed Elliptical-Rotor-Type Mixer, Kagaku Kogaku Ronbunshu, vol. 27, pp. 141–143.10.1252/kakoronbunshu.27.141 ↗
7. 7) Nogi, K., Naito, M., Kondo, A., Nakahira, A., Niihara, K. and Yokoyama, T. (1996): New Method for Elucidation of Temperature at the Interface Between Particles under Mechanical Stirring, J. Japan Soc. of Powder and Powder Metallurgy, vol. 43, pp. 396–401.10.2497/jjspm.43.396 ↗
8. 8) Fukui, T., Murata, K., Ohara, S., Abe, H., Naito, M. and Nogi, K. (2004): Morphology control of Ni?YSZ cermet anode for lower temperature operation of SOFCs, J. Powder Sources, vol. 125, pp. 17–21.10.1016/S0378-7753(03)00817-6 ↗
9. 9) Naito, M.Abe, H., Kondo, A., Yokoyama, T. and Huang, C. C. (2009): Smart Powder Processing for Advanced Materials, KONA Powder and Particle Journal No.27, pp. 130–143.10.14356/kona.2009013 ↗
10. 10) Abe, H., Abe, I., Sato, K. and Naito, M. (2005): Dry Powder Processing of Fibrous Fumed Silica Compacts for Thermal Insulation, J. Am. Ceram. Soc., vol. 88, pp.1359–1361.10.1111/j.1551-2916.2005.00317.x ↗
11. 11) Sato, K., Chaichanawong, J., Abe, H. and Naito, M. (2006): Mechanochemical synthesis of LaMnO3 fine powder assisted with water vapor, Material Letters, vol. 60, pp.1399–1402.10.1016/j.matlet.2005.11.038 ↗
12. 12) Tatami, J., Kodama, E., Watanabe, H., Nakano, H., Wakihara, T., Komeya, K., Meguro, T. and Azushima, A. (2008): Fabrication and wear properties of TiN nanoparticle-dispersed Si3N4 ceramics, J. Ceram. Soc. Japan, vol. 116, pp.749–754.10.2109/jcersj2.116.749 ↗
13. 13) Tasaki, S., Tatami, J., Nakano, H., Wakihara, T., Komeya, K. and Meguro, T. (2010): Fabrication of ZnO ceramics using ZnO/Al2O3 nanocomposite particles prepared by mechanical treatment, J. Ceram. Soc. Japan, vol. 118, pp. 118–121.10.2109/jcersj2.118.118 ↗
14. 14) Hiratsuka, D., Junichi, T., Wakihara, T., Katsutoshi, K. and Meguro, T. (2009): Fabrication of AlN ceramics using AlN and nano-Y2O3 composite particles prepared by mechanical treatment, Key Engineering Materials, vol. 403, pp. 245–24810.4028/www.scientific.net/KEM.403.245 ↗
15. 15) Kodama, E., Tatami, J., Wakihara, T., Meguro, T., Komeya, K. and Nakano, H. (2009): Fabrication and mechanical properties of TiN nanoparticle-dispersed Si3N4 ceramics from Si3N4-nano TiO2 composite particles obtained by mechanical treatment, Key Engineering Materials, vol. 403, pp. 221–224.10.4028/www.scientific.net/KEM.403.221 ↗
16. 16) Oyama, Y. and Kamigaito, S. (1971): Solid Solubility of Some Oxides in Si3N4, Jpn. J. Appl. Phys., vol. 10, pp. 1637.10.1143/JJAP.10.1637 ↗
17. 17) Jack, K. H. and Wilson, W. I. (1972): Ceramics Based on the Si-Al-O-N and Related Systems, Nature Physics Science. vol. 238, pp. 28–29.10.1038/physci238028a0 ↗
18. 18) Tsuge, A., Nishida, K. and Komatsu, M. (1975): Effect of Crystallizing the Grain-Boundary Glass Phase on the High Temperature Strength of Hot-Pressed Si3N4, J. Am. Ceram. Soc., vol. 58, pp. 323–326.10.1111/j.1151-2916.1975.tb11488.x ↗
19. 19) Komeya, K. (1984): Development of Nitrogen Ceramics, Am. Ceram. Soc., Bull., vol. 63, pp. 1158–1159.
20. 20) Yamada, T. and Kotoku, Y. (1989): Jpn. Chem. Ind. Assoc. Mon., vol. 42, pp. 8.
21. 21) Mitomo, M. (1976): Pressure Sintering of Si3N4, J. Mater. Sci., vol. 11, pp. 1103–1107.10.1007/BF02396645 ↗
22. 22) Kawamura, H. and Yamamoto, S. (1983): Improvement of Diesel Engine Startability by Ceramic Glow Plug Start System, SAE Paper, No. 830580.10.4271/830580 ↗
23. 23) Kamiya, S., Murachi, M., Kawamoto, H., Kato, S., Kawakami, S. and Suzuki, Y. (1985): Silicon Nitride Swirl Chambers for High Power Charged Diesel Engines, SAE, No. 850523.10.4271/850523 ↗
24. 24) Hattori, H., Tajima, Y., Yabuta, K., Matsuo, Y., Kawamura, M. and Watanabe, T. (1986): Gas Pressure Sintered Silicon Nitride Ceramics for Turbocharger Application, Proc. 2nd International Symposium bon Ceramic Materials and Components for Engines, pp. 165 (1986).
25. 25) Komeya, K. and Kotani, H. (1986): Development of Ceramic Antifriction Bearing, JSAE Rev., vol. 7, pp. 72–79.
26. 26) Takebayashi, H., Tanimoto, K. and Hattori, T. (1998): Performance of Hybrid Ceramic Bearing at High Speed Condition (Part 1), J. Gas Turbine Soc. Japan, vol. 26, pp. 55–60.
27. 27) Takebayashi, H., Tanimoto, K. and Hattori, T. (1998): Performance of Hybrid Ceramic Bearing at High Speed Condition (Prat 2), J. Gas Turbine Soc. Japan, vol. 26, pp. 61–66.
28. 28) Tatami, J., Toyama, M., Noguchi, K., Komeya, K., Meguro, T. and Komatsu, M. (2003): Effect of TiO2 and AlN Additions on the Sintering Behavior of the Si3N4-Y2O3-Al2O3 System, Ceramic Transactions, vol. 247, pp. 83–86.10.4028/www.scientific.net/KEM.247.83 ↗
29. 29) Yano, T., Tatami, J., Komeya, K. and Meguro, T. (2001): Microstructural Observation of Silicon Nitride Ceramics Sintered with Addition of Titania, J. Ceram. Soc. Japan, vol. 109, pp. 396–400.10.2109/jcersj.109.1269_396 ↗
30. 30) Tatami, J., Chen, I. W., Yamamoto, Y., Komastu, M., Komeya, K., Kim, D. K., Wakihara, T., Meguro, T. (2006): Fracture Resistance and Contact Damage of TiN Particle Reinforced Si3N4 Ceramics, J. Ceram. Soc. Japan, vol. 114, pp. 1049–1053.10.2109/jcersj.114.1049 ↗
31. 31) Adachi, K., Kato, K. and Chen, N. (1997): Wear Map of Ceramics, Wear, vol. 203, pp. 291–301.10.1016/S0043-1648(96)07363-2 ↗
32. 32) Zheng, S., Gao, L., Watanabe, H., Tatami, J., Wakihara, T., Komeya, K. and Meguro, T. (2007): Improving the Microstructure of Si3N4-TiN Composites Using Various PEIs to Disperse Raw TiO2Powder, Ceramics International, vol. 33, pp. 355–359.10.1016/j.ceramint.2005.10.003 ↗
33. 33) Gahlin, R. and Jacobson, S. (1999): The particle size effect in abrasion studied by controlled abrasive surfaces, Wear, vol. 224, pp. 118–125.10.1016/S0043-1648(98)00344-5 ↗
34. 34) Ogasawara, T., Tanaka, R., Sugawara, K. and Sugawara, T. (2000): Effect of the Additives on the Nonlinear Coefficient of ZnO Varistor, J. Ceram. Soc. Japan, vol. 108, pp. 565–570.10.2109/jcersj.108.1258_565 ↗
35. 35) Xu, J., Pan, Q., Shun, Y. and Tian, Z. (2000): Sens. Actuators B, vol. 66, 277–279 (2000).10.1016/S0925-4005(00)00381-6 ↗
36. 36) Ohtaki, M., Tsubota, T., Eguchi, K. and Arai, H. (1996): High-temperature thermoelectric properties of (Zn1-xAlx) O, J. Appl. Phys., vol. 79, pp. 1816–1818.10.1063/1.360976 ↗
37. 37) Nakamura, M., Ikuta, K., Aoki, T., Suzuki, A., Matsushita, T. and Okuda, M. (2008): Ultra Thin Al-doped Transparent Conducting Zinc Oxide Films Fabricated by Pulsed Laser Deposition Method, J. Vac. Soc. Jpn., vol. 51 pp. 323–325.10.3131/jvsj2.51.323 ↗
38. 38) Tsukazaki, A., Kubota, M., Ohtomo, A., Onuma, T., Ohtani, K., Ohno, H., Chichibu, S. F. and Kawasaki, M. (2005): Blue Light-Emitting Diode Based on ZnO, Jpn. J. Appl. Phys., vol. 44, pp. L643–L645.10.1143/JJAP.44.L643 ↗
39. 39) Matsuoka, M. (1971): Nonohmic Properties of Zinc Oxide Ceramics, Jpn. J. Appl. Phys., vol. 10, pp.736–746.10.1143/JJAP.10.736 ↗
40. 40) Mukae, K., Tsuda, K. and Nagasawa, I. (1977): Nonohmic properties of ZnO-rare earth metal oxide-Co3O4 ceramics, Jpn J. Appl. Phys., vol. 16, pp.1361–1368.10.1143/JJAP.16.1361 ↗
41. 41) Tanaka, M., Tsubone, T. and Yanagida, H. (1974): Electrical Conductivity of Sintered Bodies of ZnO Doped with Al2O3, Yogyo Kyokaishi, vol. 82, pp. 271–277.10.2109/jcersj1950.82.945_271 ↗
42. 42) Kaga, H., Kinemuchi, Y., Yilmaz, H., Watari, K., Nakano, H., Nakano, H., Tanaka, S., Makiya, A., Kato, Z. and Uematsu, K. (2007): Orientation dependence of transport property and microstructural characterization of Al-doped ZnO ceramics, Acta Mater., vol. 55, pp. 4753–4757.10.1016/j.actamat.2007.04.046 ↗
43. 43) Ewsuk, K. G., Ellerby, D. T. and DiAntonio, C. B. (2006): Analysis of Nanocrystalline and Microcrystalline ZnO Sintering Using Master Sintering Curves, J. Am. Ceram. Soc., vol. 89, pp. 2003–2009.10.1111/j.1551-2916.2006.00990.x ↗
44. 44) Han, J., Mantas, P. Q. and Senos, A. M. R. (2001): Densification and Grain Growth of Al-doped ZnO, J. Mater. Res., vol. 16, pp. 459–468.10.1557/JMR.2001.0069 ↗
45. 45) Shirouzu, K., Ohkusa, T., Hotta, M., Enomoto, N. and Hojo, J. (2007): Distribution and Solubility Limit of Al in Al2O3-Doped ZnO Sintered Body, J. Ceram. Soc. Japan, vol. 115, pp. 254–258.10.2109/jcersj.115.254 ↗
46. 46) Tatami, J., Katashima, T., Komeya, K., Meguro, T., Wakihara, T. (2005): Electrically Conductive CNT-Dispersed Silicon Nitride Ceramics, J. Am. Ceram. Soc., vol. 88, pp. 2899–2893.10.1111/j.1551-2916.2005.00539.x ↗