journal article·2021-01-10Open access

A Semi-Automated DEM Parameter Calibration Technique of Powders Based on Different Bulk Responses Extracted from Auger Dosing Experiments

Bilal El Kassem, Nizar Salloum, Thomas Brinz, Yousef Heider, Bernd Markert

KONA Powder and Particle Journal· Volume 38· Issue 0

Abstract

Discrete Element Method (DEM) proved to be an essential tool to optimize the industrial auger dosing process for pharmaceutical powders. During the DEM parameter calibration process of a certain powder, several parameter combinations might lead to a similar bulk response, which could also vary for other bulk responses. Therefore, a methodology is needed in order to narrow down the number of combinations and be at once close to reality representation. In this study, a vertical auger dosing setup is used as a standard calibration device to extract three different bulk responses, i.e., angle of repose, bulk density, and mass flow rate. Simulations using LIGGGHTS software package are performed based on Design of Experiments (DoE) by varying four input factors, i.e., auger speed, particle-particle and particle-wall static friction coefficients, and particle-particle rolling friction coefficient. The successful application of multivariate regression analysis (MVRA) results in predicting the bulk behavior within the studied ranges of parameters. In this regard, clustering the different predicted behaviors of the three responses together allows to dramatically reduce the admissible parameter combinations. Consequently, an optimized set of calibrated DEM parameters is chosen, where the simulation results accurately match the experimental reference data. This simple dynamic calibration tool proves to strongly verify and predict the flowability of free-flowing bulk materials.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Granular flow and fluidized beds · Mineral Processing and Grinding · Particle Dynamics in Fluid Flows

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Institute of General Mechanics, RWTH Aachen University, Germany

Robert Bosch Packaging Technology GmbH, Germany

References (54)

Show source-provided references
1. Ai J., Chen J.F., Rotter J.M., Ooi J.Y., Assessment of rolling resistance models in discrete element simulations, Powder Technology, 206 (2011) 269–282. DOI: 10.1016/j.powtec.2010.09.03010.1016/j.powtec.2010.09.030 ↗
2. Al-hashemi H.M.B., Al-amoudi O.S.B., A review on the angle of repose of granular materials, Powder Technology, 330 (2018) 397–417. DOI: 10.1016/j.powtec.2018.02.00310.1016/j.powtec.2018.02.003 ↗
3. Bierwisch C., Kraft T., Riedel H., Moseler M., Three-dimensional discrete element models for the granular statics and dynamics of powders in cavity filling, Journal of the Mechanics and Physics of Solids, 57 (2009) 10–31. DOI: 10.1016/j.jmps.2008.10.00610.1016/j.jmps.2008.10.006 ↗
4. Bierwisch C.S., Numerical Simulations of Granular Flow and Filling, Shaker Verlag GmbH, Germany, 2009, ISBN: 3832283382.
5. Börner M., Michaelis M., Siegmann E., Radeke C., Schmidt U., Impact of impeller design on high-shear wet granulation, Powder Technology, 295 (2016) 261–271. DOI: 10.1016/j.powtec.2016.03.02310.1016/j.powtec.2016.03.023 ↗
6. Ciantia M.O., Arroyo M., Butlanska J., Gens A., DEM modelling of cone penetration tests in a double-porosity crushable granular material, Computers and Geotechnics, 73 (2016) 109–127. DOI: 10.1016/j.compgeo.2015.12.00110.1016/j.compgeo.2015.12.001 ↗
7. Clearly P.W., DEM modelling of particulate flow in a screw feeder Model description, Progress in Computational Fluid Dynamics, An International Journal, 7 (2007). DOI: 10.1504/PCFD.2007.01300510.1504/PCFD.2007.013005 ↗
8. Coetzee C.J., Review: Calibration of the discrete element method, Powder Technology, 310 (2017) 104–142. DOI: 10.1016/j.powtec.2017.01.01510.1016/j.powtec.2017.01.015 ↗
9. Cundall P.A., Strack O.D.L., A discrete numerical model for granular assemblies, Géotechnique, 29 (1979) 47–65. DOI: 10.1192/bjp.115.526.106510.1192/bjp.115.526.1065 ↗
10. Derakhshani S.M., Schott D.L., Lodewijks G., Micro – macro properties of quartz sand : Experimental investigation and DEM simulation, Powder Technology, 269 (2015) 127–138. DOI: 10.1016/j.powtec.2014.08.07210.1016/j.powtec.2014.08.072 ↗
11. El Kassem B., Brinz T., Heider Y., Markert B., Experimental study and discrete element simulation of auger dosing of different pharmaceutical powders, Proceedings in Applied Mathematics and Mechanics PAMM, 18 (2018). DOI: 10.1002/pamm.20180026110.1002/pamm.201800261 ↗
12. El Kassem B., Salloum N., Brinz T., Heider Y., Markert B., A Multivariate regression parametric study on DEM input parameters of free-flowing and cohesive powders with experimental data-based validation, Computational Particle Mechanics, (2020). DOI: 10.1007/s40571-020-00315-810.1007/s40571-020-00315-8 ↗
13. Eriksson L., Johansson E., Kettaneh-Wold N., WikstrÄom C., Wold S., Design of Experiments: Principles and Applications, third edition, Umetrics AB, 2008, ISBN: 9197373044.
14. Fernandez J.W., Cleary P.W., McBride W., Effect of screw design on hopper drawdown of spherical particles in a horizontal screw feeder, Chemical Engineering Science, 66 (2011) 5585–5601. DOI: 10.1016/j.ces.2011.07.04310.1016/j.ces.2011.07.043 ↗
15. Geuzaine C., Remacle J.-F., Gmsh: A 3-D finite element mesh generator with built-in pre- and post-processing facilities, International Journal for Numerical Methods in Engineering, 79 (2009) 1309–1331. DOI: 10.1002/nme.257910.1002/nme.2579 ↗
16. Govender N., Pizette P., Wilke D.N., Abriak N.-E., Validation of the GPU based blaze-DEM framework for hopper discharge, Proceedings of the 4th International Conference on Particle-Based Methods — Fundamentals and Applications, PARTICLES 2015, (2015).
17. Heider Y., Reiche S., Siebert P., Markert B., Modeling of hydraulic fracturing using a porous-media phase-field approach with reference to experimental data, Engineering Fracture Mechanics, (2018) 116–134. DOI: 10.1016/j.engfracmech.2018.09.010.10.1016/j.engfracmech.2018.09.010 ↗
18. Hertz H., Ueber die Berührung fester elastischer Körper (“On the contact of elastic bodies”), Journal für die reine und angewandte Mathematik, 92 (1882) 156–171. DOI: 10.1515/crll.1882.92.15610.1515/crll.1882.92.156 ↗
19. Iwashita K., Oda M., Micro-deformation mechanism of shear banding process based on modified distinct element method, Powder Technology, 109 (2000) 192–205. DOI: 10.1016/S0032-5910(99)00236-310.1016/S0032-5910(99)00236-3 ↗
20. Johnstone M.W., Calibration of DEM models for granular materials using bulk physical tests, Doctoral Thesis, The University of Edinburgh, Philosophy (2010).
21. Kloss C., Goniva C., Hager A., Amberger S., Pirker S., Models, algorithms and validation for opensource DEM and CFD-DEM, Progress in Computational Fluid Dynamics, International Journal, 12 (2012) 140. DOI: 10.1504/PCFD.2012.04745710.1504/PCFD.2012.047457 ↗
22. Krantz M., Zhang H., Zhu J., Characterization of powder flow: Static and dynamic testing, Powder Technology, 194 (2009) 239–245. DOI: 10.1016/j.powtec.2009.05.00110.1016/j.powtec.2009.05.001 ↗
23. Li Y.,Xu Y., Thornton C., A comparison of discrete element simulations and experiments for “sandpiles” composed of spherical particles, Powder Technology, 160 (2005) 219–228. DOI: 10.1016/j.powtec.2005.09.00210.1016/j.powtec.2005.09.002 ↗
24. Li Z.,Yang J., Xu X., Xu X., Yu W., Yue X., Sun C., Particle shape characterization of fluidized catalytic cracking catalyst powders using the mean value and distribution of shape factors, Advanced Powder Technology, 13 (2002) 249–263. DOI: 10.1163/15685520232025243510.1163/156855202320252435 ↗
25. Lommen S., Schott D., Lodewijks G., DEM speedup: Stiffness effects on behavior of bulk material, Particuology, 12 (2014) 107–112. DOI: 10.1016/j.partic.2013.03.00610.1016/j.partic.2013.03.006 ↗
26. Lumay G., Boschini F., Traina K., Bontempi S., Remy J.C., Cloots R., Vandewalle N., Measuring the flowing properties of powders and grains, Powder Technology, 224 (2012) 19–27. DOI: 10.1016/j.powtec.2012.02.01510.1016/j.powtec.2012.02.015 ↗
27. MakeItFrom, 2019a, EN 1.4404 (X2CrNiMo17-12-2) Stainless Steel accessed 19.01.2019.
28. MakeItFrom, 2019b, Borosilicate Glass accessed 19.01.2019.
29. Marigo M., Cairns D.L., Bowen J., Ingram A., Stitt E.H., Relationship between single and bulk mechanical properties for zeolite ZSM5 spray-dried particles, Particuology, 14 (2014) 130–138. DOI: 10.1016/j.partic.2013.05.00610.1016/j.partic.2013.05.006 ↗
30. Marigo M., Stitt E.H., Discrete element method (DEM) for industrial applications: Comments on calibration and validation for the modelling of cylindrical pellets, KONA Powder and Particle Journal, 32 (2015) 236–252. DOI: 10.14356/kona.201501610.14356/kona.2015016 ↗
31. Mindlin R.D., Compliance of elastic bodies in contact, Journal of Applied Mechanics, 16 (1949) 259–268.10.1115/1.4009973 ↗
32. Moysey P.A., Thompson M.R., Modelling the solids inflow and solids conveying of single-screw extruders using the discrete element method, Powder Technology, 153 (2005) 95–107. DOI: 10.1016/j.powtec.2005.03.00110.1016/j.powtec.2005.03.001 ↗
33. Obaid A., Turek S., Heider Y., Markert B., A new monolithic Newton-multigrid-based FEM solution scheme for large strain dynamic poroelasticity problems, International Journal for Numerical Methods in Engineering, 109 (2017) 1103–1129. DOI: 10.1002/nme.531510.1002/nme.5315 ↗
34. Owen P.J., Cleary P.W., Prediction of screw conveyor performance using the Discrete Element Method (DEM), Powder Technology, 193 (2009) 274–288. DOI: 10.1016/j.powtec.2009.03.01210.1016/j.powtec.2009.03.012 ↗
35. Owen P.J., Cleary P.W., Screw conveyor performance: comparison of discrete element modelling with laboratory experiments, Progress in Computational Fluid Dynamics, An International Journal, 10 (2010) 327–333. DOI: 10.1504/PCFD.2010.03536610.1504/PCFD.2010.035366 ↗
36. Pezo L., Jovanović A., Pezo M., Čolović R., Lonćar B., Modified screw conveyor-mixers – Discrete element modeling approach, Advanced Powder Technology, 26 (2015) 1391–1399. DOI: https://doi.org/10.1016/j.apt.2015.07.016.10.1016/j.apt.2015.07.016 ↗
37. Pillai U., Heider Y., Markert B., A diffusive dynamic brittle fracture model for heterogeneous solids and porous materials with implementation using a user-element subroutine, Computational Materials Science, 153 (2018) 36–47. DOI: 10.1016/j.commatsci.2018.06.02410.1016/j.commatsci.2018.06.024 ↗
38. Qi L.,Chen Y., Sadek M., Simulations of soil flow properties using the discrete element method (DEM), Computers and Electronics in Agriculture, 157 (2019) 254–260. DOI: 10.1016/j.compag.2018.12.05210.1016/j.compag.2018.12.052 ↗
39. Roberts A.W., The influence of granular vortex motion on the volumetric performance of enclosed screw conveyors, Powder Technology, 104 (1999) 56–67. DOI: 10.1016/S0032-5910(99)00039-X10.1016/S0032-5910(99)00039-X ↗
40. Roessler T., Katterfeld A., DEM parameter calibration of cohesive bulk materials using a simple angle of repose test, Particuology, 45 (2019) 105–115. DOI: 10.1016/j.partic.2018.08.00510.1016/j.partic.2018.08.005 ↗
41. Roessler T., Richter C., Katterfeld A., Will F., Development of a standard calibration procedure for the DEM parameters of cohesionless bulk materials – part I: Solving the problem of ambiguous parameter combinations, Powder Technology, 343 (2018) 803–812. DOI: 10.1016/j.powtec.2018.11.03410.1016/j.powtec.2018.11.034 ↗
42. Shimizu Y., Cundall P., Three-dimensional DEM simulations of bulk handling by screw conveyors, Journal of Engineering Mechanics, 127 (2001) 864–872. DOI: 10.1061/(ASCE)0733-9399(2001)127:9(864)10.1061/(ASCE)0733-9399(2001)127:9(864) ↗
43. Sinnott M.D., Cleary P.W., The effect of particle shape on mixing in a high shear mixer, Computational Particle Mechanics, 3 (2016) 477–504. DOI: 10.1007/s40571-015-0065-410.1007/s40571-015-0065-4 ↗
44. Souihi N., Josefson M., Tajarobi P., Gururajan B., Trygg J., Design space estimation of the roller compaction process, Industrial & Engineering Chemistry Research, 52 (2013) 12408–12419. DOI: 10.1021/ie303580y10.1021/ie303580y ↗
45. Sundararajan K., 2018, Design of Experiments- A Primer accessed 22.04.2020.
46. Triefenbach F., Design of experiments: The D-optimal approach and its implementation as a computer algorithm, Bachelor’s Thesis, Umea University and South Westphalia University of Applied Sciences, 2008.
47. Wang Z., Jacobs F., Ziegler M., Experimental and DEM investigation of geogrid-soil interaction under pullout loads, Geotextiles and Geomembranes, 44 (2016) 230–246. DOI: 10.1016/j.geotexmem.2015.11.00110.1016/j.geotexmem.2015.11.001 ↗
48. Wensrich C.M., Katterfeld A., Rolling friction as a technique for modelling particle shape in DEM, Powder Technology, 217 (2012) 409–417. DOI: 10.1016/j.powtec.2011.10.05710.1016/j.powtec.2011.10.057 ↗
49. Wilkinson S.K., Turnbull S.A., Yan Z., Stitt E.H., Marigo M., A parametric evaluation of powder flowability using a Freeman rheometer through statistical and sensitivity analysis: A discrete element method (DEM) study, Computers and Chemical Engineering, 97 (2017) 161–174. DOI: 10.1016/j.compchemeng.2016.11.03410.1016/j.compchemeng.2016.11.034 ↗
50. Yan Z., Wilkinson S.K., Stitt E.H., Marigo M., Discrete element modelling (DEM) input parameters: Understanding their impact on model predictions using statistical analysis, Computational Particle Mechanics, 2 (2015) 283–299. DOI: 10.1007/s40571-015-0056-510.1007/s40571-015-0056-5 ↗
51. Zhou D., Qiu Y., Understanding material properties in pharmaceutical product development and manufacturing: Powder flow and mechanical properties, Journal of Validation technology, 73 (2010) 65–77. DOI: 10.6061/clinics/2018/e26410.6061/clinics/2018/e264 ↗
52. Zhou Y.C., Xu B.H., Yu B., Zulli P., An experimental and numerical study of the angle of repose of coarse spheres, Powder Technology, 125 (2002) 45–54. DOI: 10.1109/MACE.2011.598691010.1016/S0032-5910(01)00520-4 ↗
53. Zhu H.P., Zhou Z.Y., Yang R.Y., Yu A.B., Discrete particle simulation of particulate systems: Theoretical developments, Chemical Engineering Science, 62 (2007) 3378–3396. DOI: 10.1016/j.ces.2006.12.08910.1016/j.ces.2006.12.089 ↗
54. Zhu H.P., Zhou Z.Y., Yang R.Y., Yu A.B., Discrete particle simulation of particulate systems: A review of major applications and findings, Chemical Engineering Science, 63 (2008) 5728–5770. DOI: 10.1016/j.ces.2008.08.00610.1016/j.ces.2008.08.006 ↗