A Review of the Fire and Explosion Hazards of Particulates
Source abstract
Abstract
Particulate fires and explosions cause substantial loss of life and property. With the goal of understanding, preventing, or at least mitigating particulate fire and explosion hazards, we review basics. We distinguish between ‘hazard’ and ‘risk’ and discuss the fire and explosion hazards of particulates, the many factors determining such hazards, hazard indexes, and ways to reduce fire and explosion hazards. While our primary goal is to improve safety, we briefly discuss how fundamental knowledge can be extracted from weapon technology based on particulate combustion. We review the prevention of and protection against particulate explosions and discuss ongoing and future research.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Combustion and Detonation Processes · Risk and Safety Analysis · Fire dynamics and safety research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Chemical Engineering, Delft University of Technology
Mary Kay O’Connor Process Safety Center, Department of Chemical Engineering of Texas A&M University
References (100+)
Show source-provided references
1. 1) Lemkowitz, S. M. and Pasman, H. J. (2013): discuss particulate fire and explosion risks in “Assessment and Control of Fire and Explosion Hazards and Risks of Particulates”, Chapter 4, Merkus, H. G. and Meesters, G. M. H. (Editors), “Particulate Products—Design Properties for Performance Optimization”, pp. 77–120, .Springer, 2013 (ISBN: 978-3-319-00713-7).
2. 2) While dust explosion hazards are extensively studied, much less is available for mist explosions. Examples are: Gant, S, Bettis, R., Santon, R., Bickland, I., Bower, Ph. and Kay, P. (2012), “Generation of Flammable Mists from High Flash-point Fluids: Literature Review”, presented at Institution of Chemical Engineers, XXIII Conference, Southport, UK, 12–15 November 2012, available as: http://s177835660.websitehome.co.uk/research/gant_bettis_santon_buckland_bowen_kay_2012_mists_lit_review_preprint.pdf, 19 pages;
3. 2) Förster, H. (2004), Chapter 5, “Properties of Flammable Mists and Foams”, p. 419–480, from M. Hattwig, M. and Steen, H., “Handbook of Explosion Prevention and Protection”, Wiley-VCH, 2004 (ISBN: 3-527-30718-4);10.1002/9783527612468.ch5 ↗
4. 2) Krishna, K., Rogers, W. J. and Mannan, M. S. (2003), “The use of aerosol formation, flammability, and explosion information for heat-transfer fluid selection”, Journal of Hazardous Materials 104, pp. 215–226;10.1016/S0304-3894(03)00273-5 ↗
5. 2) Holness, M. H. and Smith, B. J. (2002), “Oil Mist and Machinery Space Fires”, Marine Technology, 39(1), 2002, pp. 62–66;10.5957/mt1.2002.39.1.62 ↗
6. 2) Britton, L. G. (1999), “Avoiding Static Ignition Hazards in Chemical Operations,” Center for Chemical Process Safety, American Institute of Chemical Engineers, pp. 83–96, 209–211.10.1002/9780470935408 ↗
7. 3) See for example, Eckhoff, R. K. (2003), “Dust Explosions in the Process Industries”, Third Edition, Elsevier, (ISBN: 0-7506-7602-7), in particular Table A.1, pages 686–699, which lists explosion severity and sensitivity indexes, including Pmax, for ca. 600 different powders.
8. 4) Lemkowitz, S. M. and Scholten, R. M. (1999), “Explosion theory for dummies”, NPT Process Techniek, 2, pp. 19–24. Derivation is based on assumptions that flame thickness is small relative to vessel diameter and that flame speed is independent of temperature and pressure.
9. 5) Hertzberg et al, 1986 derive a formula very similar to Eq. 4 applied to gases, i.e. for flames whose thickness is small relative to the radius of vessels in which explosion occurs. Hertzberg, M., Cashdollar, K. L., and Zlochower, I. A. (1986), "Flammability Limit Measurements For Dusts and Gases: Ignition Energy Requirements and Pressure Dependences", Twenty-first Symposium (International) on Combustion, the Combustion Institute, pp. 303-31310.1016/S0082-0784(88)80258-3 ↗
10. see Eq. 5, page 307. Cashdollar (2000) obtains the same equation as Hertzberg et al. (1986), but applies it to dust explosions, commenting that the equation is probably more valid in the standard 1000 liter testing sphere than in the, also standard, 20 liter sphere due to the greater radius of the 1000 liter sphere, relative to dust flame thickness.
11. 5) Cashdollar, K. L. (2000), “Overview of dust explosibility characteristics”, Journal of Loss Prevention in the Process Industries, 13, pp. 183–199. See Eqs. 6–7, page 188.10.1016/S0950-4230(99)00039-X ↗
12. 6) Dahoe et al. (1996, 2003) derive more realistic—and considerably more complex—equations describing flame speed effects on pressure rise and K factor for thick dust flames, which are typical of particulate explosions. Dahoe, A. E. and de Goey, L. P. H. (2003), “On the determination of the laminar burning velocity from closed vessel gas explosions”, Journal of Loss Prevention in the Process Industries, 16, pp. 457–478;10.1016/S0950-4230(03)00073-1 ↗
13. 6) Dahoe, A. E., Zevenbergen, J. F., Lemkowitz, S. M., and Scarlett, B. (1996), “Dust explosions in spherical vessels: the role of flame thickness in the validity of the ‘cube-root-law’”, Journal of Loss Prevention in the Process Industries, 9, pp. 33–4410.1016/0950-4230(95)00054-2 ↗
14. 7) Center for Chemical Process Safety (2012), “Guidelines for Evaluating Process Plant Buildings for External Explosions, Fire, and Toxic Releases”, Second Edition, Wiley (ISBN 978-0-470-64367); see p. 62.
15. 8) Center for Chemical Process Safety (1994), “Guidelines for Evaluating the Characteristics of Vapor Cloud Explosions, Flash Fires, and BLEVEs”, first edition, American Institute of Chemical Engineers; see Table 4.1a, p. 72.
16. 9) Abbasi, T., Pasman, H. J., Abbasi, S. A. (2010), A scheme for the classification of explosions in the chemical process industry, Journal of Hazardous Materials, 174, pp. 270–280.10.1016/j.jhazmat.2009.09.047 ↗
17. 10) Mannan, S. editor (2012), “Lees’ Loss Prevention In The Process Industries, Fourth Edition, Chapter 17, “Explosion”, Elsevier, ISBN 978-0-123-971890
18. 11) Using such indexes (Tables 1 and 2), in combination with chemical thermodynamic data and data from practice (e.g., accidents), the National Fire Protection Agency (NFPA) ranks hazards of powders in terms of Health, Fire, and Instability. See Center for Chemical Process Safety, (2005), “Guidelines for Safe Handling of Powders and Bulk Solids”.
19. 12) On the basis of a number of simplifying assumptions, and using only secondary school chemistry and physics, Lemkowitz and Scholten correctly derive, in terms of trends, how changes in ambient temperature, pressure, and flow (turbulence) affect nearly all important fire and explosion indexes: Lemkowitz, S. M. and Scholten, R. M. (1999), op cit.
20. 13) Detailed discussions of test methods for powders and their evaluation are given in: J. Barton (2002)), “Dust Explosion Prevention and Protection—A Practical Guide”, Institution of Chemical Engineers; see Chapter 2: “Determination of dust ignitability, flammability and explosibility characteristics”, pp. 8–20; Eckhoff, R. (2003), “Dust Explosions in the Process Industries”, Third Edition, Butterworth-Heinemann, see Chapter 7, “Assessment of ignitability, explosibility, and related properties of dusts by laboratory-scale tests; pp. 473–548.10.1016/B978-075067602-1/50008-1 ↗
21. 14) Gao, W., Zhong, S., Miao, N., and Liu, H. (2013), “Effect of ignition on the explosion behavior of 1-Octadecanol/air mixtures”, Powder Technology, 241, pp. 105–114.10.1016/j.powtec.2013.03.015 ↗
22. 15) Proust, Ch., Accorsi, A., and Dupont, L. (2007), “Measuring the violence of dust explosions with the “20 l sphere”and the standard “ISO 1 m3 vessel—Systematic comparison and analysis of the discrepancies”, Journal of Loss Prevention in the Process Industries, 20, pp. 599–606.10.1016/j.jlp.2007.04.032 ↗
23. 16) Detailed descriptions of hazards of unstable liquids and their control are given by L. A. Medard (1989) in: “Accidental Explosions” Volumes 1 (ISBN 0470215305) and Volume 2 (ISBN 0-7458-0436-5). Ellis Horwood Ltm (English translations of the original French language text of 1987).
24. 17) Powdered ammonium nitrate, mixed with an inert compound such as calcium carbonate to reduce its explosion hazard (‘phlegmatizing’ it), is a widely used fertilizer. In spite phlegmatizing inerts, a number of serious explosions of large piles of powdered ammonium nitrate have nevertheless occurred.
25. 18) Examples of pyrophoric substances are found in Johnson, R. W., Rudy, S. W., and Unwin, S. D. (2003), “Essential Practices for Managing Chemical Reaction Hazards”, Center for Chemical Process Safety, American Institute of Chemical Engineering, Table 3.2, page 45.
26. 19) The above source also lists common water-reactive substances (Table 3.4, page 50) as also does ‘Common Water Reactive Chemicals’, http://www.esd.uga.edu/chem/pub/waterreactivemat.pdf.
27. 20) Going, J. E. and Snoeys, J. (2002), “Explosion Protection with Metal Dust Fuels”, Process Safety Progress, 21(4), pp. 305–312.10.1002/prs.680210407 ↗
28. 21) In some cases, such as explosions of finely divided metals (e.g., powdered aluminum), even three phases can be simultaneously present: a solid phase (solid aluminum oxide), a liquid phase (molten aluminum), and a gaseous phase (air, even vaporized aluminum).
29. 22) P. Puri, P. (2008), “Multiscale modelling of ignition and combustion of micro and nano aluminum particles”, PhD Dissertation, The Pennsylvania State University, In his 235 page thesis Puri discusses combustion mechanisms of metal particles in great detail, including many splendid color figures. Full dissertation available via: http://search.proquest.com/docview/231495775
30. 23) Lecture of Puri, P. and V. Yang, V. (2005), "Multi-Scale Modeling of Nano Aluminum Particle Ignition and Combustion", Sheet 6, lecture presented in 2005 at MURI NEEM Program Review, Aberdeen, Maryland
31. full lecture available as: http://soliton.ae.gatech.edu/people/vigor.yang/projects/Nano%20Aluminum...(Puneesh)/ARO-MURI%20NEEM%20Website-(11-16-05).pdf. See also Yang, V., Sundaram, D., and Puni, P. (2010), "Multi-Scale Modeling of Nano Aluminum Particle Ignition and Combustion", lecture presented in 2010 MURI NEEM Program Review, Aberdeen, Maryland, March 15, 2010. Sheet 3. Lecture available as: http://www.neem.psu.edu/2010%20Review%20Meeting/GeorgiaTech_Yang_NEEM_MURI_Final_Review_15_March_2010.pdf
32. 24) Kobiera, A., Szymczyk, J., Wolanski, P., and Kuhl, A (2009), “Study of the shock-induced acceleration of hexane droplets”, Shock Waves, 18.4, pp. 475–485.10.1007/s00193-008-0184-4 ↗
33. 25) Dobashi, R. (2008), “Risk of dust explosions of combustible nanomaterials”, Journal of Physics: Conference Series, IOP Publishing, 170, Figure 3 on page 3.10.1088/1742-6596/170/1/012029 ↗
34. 26) R. Dobashi, R. (2008), “Risk of dust explosions of combustible nanomaterials”, sheet 19 of lecture presented at Nanosafe 2008, International Conference on Safe Production and Use of Nanomaterials; lecture available as: http://www.nanosafe.org/home/liblocal/docs/2008_Oral%20presentations/PL7_Dobashi.pdf
35. 27) Föster, H. (2004), “Properties of Flammable Mists and Foams”, Chapter 5 of “Handbook of Explosion Prevention and Protection”, edited by Hattwig, M. and Steen, H. Wiley-VCH Verlag, 2004 (ISBN: 3-527-30718-4), Figure 5.1-6, page 435.
36. 28) Dobashi, R. (2008), op cit, sheet 20 from 2008 lecture of Dobashi.10.4325/seikeikakou.20.284 ↗
37. 29) Ballal, D. R. (1980), “Ignition and Flame Quenching of Quiescent Dust Clouds of Solid Fuels”, Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, 369, pp. 479–500.10.1098/rspa.1980.0012 ↗
38. 30) The Sauter mean diameter (SMD, d32 or D[3, 2]) is an average of particle size. It is defined as the diameter of a sphere that has the same volume/surface area ratio as the particle of interest.
39. 31) Eckhoff, R. K. (2003), op cit, page 479.
40. 32) Eckhoff does, however, mention (p. 490) a related essential point, namely that a measured particle size distribution may be quite different from that occurring in practice, due to how in practice a powder is dispersed and suspended.
41. 33) Föster, H. (2004), op cit., see pages 423–425 and 235.
42. 34) Merkus, H. G. (2009), “Particle Size Measurements—Fundamentals, Practice, Quality”, Springer (ISBN: 978-1-4020-9015-8 en e-ISBN: 978-1-4020-9016-5). See pp 140–146.
43. 35) Amyotte, P. R., Chippett, S., and Pegg, M. J. (1989), “Effects of Turbulence on Dust Explosions”, Progress in Energy and Combustion Science, 14, pp. 293–310; see also Lemkowitz and Scholten, 1999, op cit.10.1016/0360-1285(88)90016-0 ↗
44. 36) A detailed discussion of film theory in describing heterogeneous combustion is given in: Annamalei, K.et al.. (1994), “Interactive Processes in Gasification and Combustion-Part III: Coal/Char Particle Arrays, Streams and Clouds”, Prog. Energy Combust. Sci. 20, 487–618; see especially pages 491–494.10.1016/0360-1285(94)90002-7 ↗
45. 37) For detailed discussion of secondary dust explosions see: Taveau, J. (2012), “Secondary Dust Explosions: How to Prevent Them or Mitigate Their Effects”, Process Safety Progress, 31(1), pp. 36–50.10.1002/prs.10478 ↗
46. 38) A comprehensive and detailed analysis (85 pages) of such an explosion, caused in part by poor housekeeping, is given in: U.S. Chemical Safety and Hazard Investigation Board, Sugar Dust Explosion and Fire (14 Killed, 36 Injured), Investigation Report No. 2008-05-I-GA, September 2009; available as: http://www.csb.gov/assets/document/Imperial_Sugar_Report_Final_updated.pdf
47. 39) Proust discusses DDTs through flame acceleration in connecting pipe work: Proust, Ch. (1996), “Dust explosions in pipes: a review”, Journal of Loss Prevention in the Process Industries, 4(9), pp. 267–277.10.1016/0950-4230(96)00010-1 ↗
48. 40) R. K. Eckhoff, R. K. (2003), op cit, pages 74 and 525
49. see also Crowl, D. A. (2003), "Understanding Explosions", Center for Chemical Process Safety, American Institute of Chemical Engineers, (ISBN 0-8169-0779-X), pp. 63-64.
50. 41) See for example, Dahoe, A. E., Cant, R. S., Pegg, M. J. and Scarlett, B. (2001), “On the transient flow in the 20-liter explosion sphere”, Journal of Loss Prevention in the Process Industries 14, pp. 475–48710.1016/S0950-4230(01)00052-3 ↗
51. 42) For more detail see: Dahoe, A. E., “Dust Explosions: A Study of Flame Propagation”, PhD Dissertation, Delft University of Technology, 2000, 297 pages (ISBN: 90-90-13706-8); see especially pages 174–181.
52. 43) van Laar, G. F. M. and Zeeuwen, J. P. (1981), “On the Minimum Ignition Energy of Dust-Air Mixtures”, Archivum Combustionis, 5, pp. 145–159R. A extensive study of effects ab//adsorbed water of explosion indexes is: J. P. Zeeuwen and G. F. M. van Laar (1983), “An overview of the research at TNO in the dust explosion field over the last decade”, Figure 6, page 83, of VDI-Berichte 494 (1983), “Sichere Handhabung brennbarer Stäube”, VDI-Verlag GmbH, Verlag des Vereins Deutscher Ingenieurs, Düsseldorf.
53. 44) Glor, M. (1988), “Electrostatic Hazards in Powder Handling”, Chapter 2, Charging of particles, Chapter 3, Ignition of particles, Wiley (ISBN: 0-471-92024).
54. 45) Hertzberg, M. and Cashdollar, K. L. (1987), “Introduction to Dust Explosions”, from Hertzberg, M. and Cashdollar, K. L. (editors), “Industrial Dust Explosions”, ASTM (American Society for Testing Materials), 1987 (ISBN: 0-8031-0957-1); modified version of Figure 5, page 14.10.1520/STP28163S ↗
55. 46) Bartknecht, W., (1981), “Explosions”, Springer-Verlag, 1981 (ISBN: 3-540-10216-7), pp. 49–55. Many of Bartknecht’s original figures continually reappear in modified form in standard works on dust explosions, such as Eckhoff’s 2003 textbook.
56. 47) Modified from Pellmont, G. (1979), “Explosions- und Zündverhalten von Hybriden Gemischen aus brennbaren Stäuben und Brenngasen”, PhD thesis, No. 6498, ETH Zürich. Figure 7 here is taken from Eckhoff, R. K. (2003), op cit, Figure 1.60, p. 52.
57. 48) Modified from Bartknecht, W. (1981), “Explosions—Course, Prevention, Protection”, Springer-Verlag, Fig. 1–5.4, p. 51. Figure 8 here is taken from Eckhoff, R. K. (2003), op cit, Figure 1.65, p. 55.
58. 49) Lavoie, L. (1989), “Fuel-Air Explosives, Weapons, and Effects”, Military Technology—MILTECH, 9, pp. 64–70.
59. 50) Rao, A. A., (1987), “Fuel Air Explosives”, Defence Science Journal, 37(1), pp. 23–28;10.14429/dsj.37.5888 ↗
60. 50) Liu, G., Hou, F., Cao, B., Xie, L., Shen, Zh., and Zhou,T. (2008), “Experimental Study of Fuel-Air Explosive”, Combustion, Explosion, and Shock Waves, 44(2), pp. 213–217.10.1007/s10573-008-0028-7 ↗
61. 51) Dearden, P., (2001), “New Blast Weapons”, Journal of the Royal Army Medical Corps, 147 (1), 2001, 80–86. Available as: http://www.ramcjournal.com/content/147/1/80.full.pdf+html;10.1136/jramc-147-01-08 ↗
62. 51) Wildegger-Gaissmaier, A. E., “Aspects of thermobaric weaponry”, ADF Health (Health Journal for the Australian Department of Defence—Joint Health Command), 4, pp. 3–6, 2003; article available as: http://www.defence.gov.au/health/infocentre/journals/ADFHJ_apr03/ADFHealth_4_1_03-06.pdf
63. 52) Pierce, T. H., Sedgwick, R. T. and Groethe, M. A. (1982), “Investigation of a Reusable Fuel-Air Explosive Nuclear Airblast Simulator”, Defense Nuclear Agency (Washington D.C.), 133 pages. Abstract available as: http://oai.dtic.mil/oai/oai?verb=getRecord&metadataPrefix=html&identifier=ADA14947310.21236/ADA149473 ↗
64. 53) Direct ignition of detonations of gaseous fuel-air mixtures requires high energies, typically (more than) a million times greater than those required to ignite deflagrations. See for example, Center for Chemical Process Safety (2010), “Guidelines for Vapor Cloud Explosion, Pressure Vessel Burst, BLEVE and Flash Fire Hazards”, Second Edition, Wiley, (ISBN 978-0-470-25147-9), Table 4.2, page 55.
65. 54) The generic nature of management failure in causing industrial explosions is clearly shown in, for example, many publications of the United States Chemical Safety Board. (http://www.csb.gov/), like the investigation of the 2009 explosion at the Imperial Sugar plant that killed 14 workers and totally destroyed the plant. Other publicly available investigations of industrial disasters (e.g., Flixborough, Seveso, Piper Alpha, Chernobyl, BP Texas City explosion, BP Deepwater Horizon oil spill) all show management failure, not lack of scientific knowledge, to be the basic cause of disasters.
66. 55) For example: Center for Chemical Process Safety: (2011), "Guidelines for Auditing Process Safety Management Systems, 2nd Edition", Wiley (ISBN: 978-0-470-28235-9)
67. (2008) Guidelines for the Management of Change for Process Safety, Wiley (ISBN: 978-0-470-04309-7)
68. 56) For example see: Britton, L. G. (1999), “Avoiding Static Ignition Hazards in Chemical Operations”, Center for Chemical Process Safety (ISBN: 0-8169-0800-1); and Glor, M. (1988), op cit.
69. 57) For example: Vijayaraghavan, G. (2011), “Review Article: Dust Explosions - A Major Industrial Hazard”, International Journal of Advanced Engineering Technology, Vol. II/Issue IV, pp. 83–87;
70. 57) Amyotte, P. R. and Eckhoff, Rolf K., P. R. (2010), “Dust explosion causation, prevention and mitigation: An overview”, Journal of Chemical Health & Safety, pp. 15–28;10.1016/j.jchas.2009.05.002 ↗
71. 57) Eckhoff, R. K. (2009), “Understanding dust explosions: The role of powder science and technology”, Journal of Loss Prevention in the Process Industries, 22, pp. 105–116;10.1016/j.jlp.2008.07.006 ↗
72. 57) Eckhoff, R. K. (2009), “Dust Explosion Prevention and Mitigation, Status and Developments in Basic Knowledge and in Practical Application”, International Journal of Chemical Engineering, pp. 1–12;10.1155/2009/569825 ↗
73. 57) Abbasi, T and Abbasi, S. A., (2007) “Dust explosions—Cases, causes, consequences, and control”, Journal of Hazardous Materials, 140, pp. 7–44;10.1016/j.jhazmat.2006.11.007 ↗
74. 57) Amyotte, P. R., Pegg, M. J., Khan, F. I., Nifuku, M., and Yingxin, T., (2007) “Moderation of dust explosions”, Journal of Loss Prevention in the Process Industries, 20, pp. 675–687;10.1016/j.jlp.2007.05.011 ↗
75. 57) Pekalski, A. A., Zevenbergen, J. F., Lemkowitz, S. M. and Pasman, H. J., (2005), “A Review of Explosion Prevention and Protection Systems Suitable as ultimate Layer of Protection in Chemical Process Installations”, Trans IChemE, Part B, Process Safety and Environmental Protection, 83(B1), pp. 1–17.10.1205/psep.04023 ↗
76. 58) Center for Chemical Process Safety (2009), “Inherently Safer Chemical Processes: A Life Cycle Approach”, 2nd Edition (ISBN: 978-0-471-77892-9). Layer of Protection Analysis (LOPA) and Inherently Safer Design (ISD) are examples of parts of the systematic, science-based discipline of Loss Prevention.
77. 59) Center for Chemical Process Safety (CCPS), Layer of Protection Analysis—Simplified Process Risk Assessment, American Institute of Chemical Engineers, 2001 (ISBN 0-8169-0811-7).
78. 60) For an overview of Loss Prevention, see, for example, Mannon, Ref. 15 in the Appendix.
79. 61) See, for example, Chapter 13, “The Role of Inherently Safer Design in Dust Explosion Prevention and Mitigation”, from Kletz, T. and Amyotte, P. (2010), “Process Plants: A Handbook for Inherently Safer Design”, Second Edition, CRC Press, ISBN: 978-1-4398-0455-1, pp. 289–318;10.1201/9781439804568-c13 ↗
80. 61) Amyotte, P. R., Pegg, M. J. and Khan, F. I. (2009), “Application of inherent safety principles to dust explosion prevention and mitigation”, Process Safety and Environmental Protection, 87, pp. 35–39;10.1016/j.psep.2008.06.007 ↗
81. 61) Dufaud, O., Perrin, L. and Laurent, A. (2010), “State of the art: promotion of early inherently safer design against dust explosions”, paper presented at CISAP4, 4th International Conference on Safety and Environment, Florence, Italy; available as: http://www.aidic.it/CISAP4/webpapers/74Dufaud.pdf
82. 62) Vignes, A., Muñoz, F., Bouillard, J., Dufaud, O., Perrin, L., Laurent, A. and Thomas, D. (2012), “Risk assessment of the ignitability and explosivity of aluminum nanopowders”, Process Safety and Environmental Protection, 90, pp. 304–310.10.1016/j.psep.2011.09.008 ↗
83. 63) Zhang, Q., Zhong, S. and Jiang, G. (2011), “Development of an Expert System for Dust Explosion Risk Management Based on ASP. Net and Prolog”, Journal of Software, 6(9), pp. 1857–1865.10.4304/jsw.6.9.1857-1865 ↗
84. 64) Pasman, H. J., Knegtering, B., and Rogers, W. J. (2013), “Review: A holistic approach to control process safety risks: Possible ways forward”, Reliability Engineering and System Safety, 117, pp. 21–29.10.1016/j.ress.2013.03.010 ↗
85. 65) See, for example, Baukal, C. E. (2013), “The John Zink Hamworthy Combustion Handbook”, Second Edition: Volume 1—Fundamentals, CRC Press. ISBN: 978-1-4398-3962-1.
86. 66) For example: Veyssiere, B., Khasainov, B. A., and Ingignoli, W., W. (2010), “Shock Initiation of Detonations in Aluminum-Oxygen Mixtures”, pp. 297–310, in Roy, G. D. and Frolov, S. M. (editors) “Deflagrative and Detonation Combustion”, Torus Press (ISBN: 978-5-94588-071-9).
87. 67) Examples being: Proust, Ch. (2006), “A few fundamental aspects about ignition and flame propagation in dust clouds”, Journal of Loss Prevention in the Process Industries, 19, pp. 104–120;10.1016/j.jlp.2005.06.035 ↗
88. 67) Eckhoff, R. K. (2005), “Current Status and Expected Future Trends in Dust Explosion Research”, Journal of Loss Prevention in the Process Industries, 18, pp. 225–237;10.1016/j.jlp.2005.06.012 ↗
89. 67) Eckhoff, R. K. (1993), “Dust explosion research. State-of-the-art outstanding problems”, Journal of Hazardous Materials, 35, pp. 103–117;10.1016/0304-3894(93)85026-B ↗
90. 67) Kauffman, C. W., Sichel, M. and Wolanski, P. (1992), “Research on dust explosions at the University of Michigan”, Powder Technology, 71, pp. 119–134.10.1016/0032-5910(92)80002-E ↗
91. 68) Hinkley, G. K. and Stephen M. Roberts, S. M. (2013), Chapter 5, pp. 121–149, “Particle and Fiber Toxicology”, from Merkus, H. G. and Meesters, G. M. H. (Editors), “Particulate Products—Design Properties for Performance Optimization”, Springer, 2013 (ISBN: 978-3-319-00713-7).
92. 69) Safety and health issues are central in the Nanosafe: Safe Production and Use of Nanomaterials. International conferences held biannually in Grenoble, France in 2008, 2010, and 2012. Noticeable is that while in 2008 and 2010 fire and explosion safety issues were discussed in many lectures, since then these issues seem relatively clear, in comparison with health issues, which in 2012 still received much attention. Lectures available on the web. For 2008: http://www.nanosafe.org/scripts/home/publigen/content/templates/show.asp?P=96&L=EN&ITEMID=42. For 2010: http://www.nanosafe.org/scripts/home/publigen/content/templates/show.asp?P=118&L=EN. For 2012: http://www.nanosafe.org/scripts/home/publigen/content/templates/show.asp?P=124&L=EN
93. 70) Eckhoff, R. K. (2012), “Does the dust explosion risk increase when moving from μm-particle powders to powders of nm-particles?”, Journal of Loss Prevention in the Process Industries, 25, pp. 448–459.10.1016/j.jlp.2011.11.011 ↗
94. 71) Wu, H-C, Chang, R-C, and Hsiao, H-C. (2009), “Research of minimum ignition energy for nano Titanium powder and nano Iron powder”, Journal of Loss Prevention in the Process Industries, pp. 21–24.10.1016/j.jlp.2008.10.002 ↗
95. 72) Eckhoff, R. K. (2013), “Influence of dispersibility and coagulation on the dust explosion risk presented by powders consisting of nm-particles”, Powder Technology, 239, pp. 223–230.10.1016/j.powtec.2013.02.007 ↗
96. 73) Yetter, R. A., Risha, G. A., and Son, S. F. (2009), “Metal particle combustion and nanotechnology”, Proceedings of the Combustion Institute 32, pp. 1819–1838; e.g. see p. 1822.10.1016/j.proci.2008.08.013 ↗
97. 74) Evans, J. P., Borland, W. and Mardon, P. G. (1976) “Pyrophoricityof fine metal; powders”, Powder Metallurgy, 1, pp. 17–21.10.1179/pom.1976.19.1.17 ↗
98. 75) Mohan, S., Ermoline, A. and Dreizin, E. L. (2012), “Pyrophoricity of nano-sized aluminum particles”, Journal of Nanoparticle Research, 14(2), pp. 1–6.10.1007/s11051-012-0723-x ↗
99. 76) Sundaram D. S., Puri P. and Yang V. (2013): Pyrophoricity of nascent and passivated aluminum particles at nano-scales, Combustion and Flame, 160, pp. 1870–1875.10.1016/j.combustflame.2013.03.031 ↗
100. 77) Krietsch, A., Romahn, T., Scheid, M. and Krause, U. (2013), “Modified Setup of 20-L-Sphere for the Determination of Safety Characteristics of Nano Powders” Chemical Engineering Transactions, 31, pp. 805–810, DOI:10.3303/CET1331135.