journal article·2011Open access

Electrical Tomography: a review of Configurations and Applications to Particulate Processes

Maria G. Rasteiro, Rui C. C. Silva, Fernando A. P. Garcia, Pedro M. Faia

KONA Powder and Particle Journal· Volume 29· Issue 0

Abstract

Despite decades of research, the study of suspension flows still continues to be a subject of great scientific interest. In the development of accurate models for suspension-related processes, prior knowledge of several flow characteristics is essential, such as spatial distribution of phases, flow regimen, relative velocity between phases, etc. Several non-invasive techniques of flow characterisation can be found in the literature, however, electrical tomography offers a vast field of possibilities due to its low cost, portability and, above all, safety of handling. In this paper, a review of the use of electrical tomography for industrial/process monitoring purposes will be presented, giving information about the evolution throughout the years and about the limitations and advantages of the different configurations. Moreover, the signal de-convolution strategies, to obtain the images of the process, will also be discussed. The most recent advances in both fields will be presented. Additionally, information about the strategy adopted by the authors to produce a portable EIT system will be described. Finally, the future challenges for electrical tomography will be addressed.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Electrical and Bioimpedance Tomography · Flow Measurement and Analysis · Microfluidic and Bio-sensing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Chemical Engineering, Faculty of Sciences and Technology, University of Coimbra

Department of Electric and Computers Engineering, Faculty of Sciences and Technology, University of Coimbra

References (74)

Show source-provided references
1. 1) Torczynski, J.R., O'Hern, T.J., Adkins, D.R., Jackson, N.B. and Shollenberger, K.A. (1997): Advanced Tomographic Flow Diagnostics for Opaque Multiphase Fluids, Sandia Report SAND97-1176 • UC-406, Sandia National Laboratories, Albuquerque, New Mexico, USA.10.2172/481578 ↗
2. 2) Abel, N.H. (1826): Resolution d'un probleme de mecanique, J. Reine Agnew. Math., 1, pp. 311–389.
3. 3) Radon, J. (1917): Über die Bestimmung von Funktionen durch ihre Integralwerte längs gewisser Mannigfaltigkeiten, Ber. Saechs. Akad. Wiss. 69, pp.262–278.
4. 4) Seeram, E. (2000): “Computed Tomography: Physical Principles, Clinical Applications, and Quality Control”, W.B Saunders Comp.
5. 5) Plakowski, A., Beck, M.S., Thorn, R. and Dyakowski, T. (1995): “Imaging Industrial Flows”, IOP Publishing, Bristol.
6. 6) Williams, R.A. and Beck, M.S. (1995): “Process Tomography—Principles, Techniques and Applications”, Butterworth-Heinemann, Oxford.
7. 7) Mewes, D. and Schmitz, D. (1999): Tomographic methods for the analysis of flow patterns in steady and transient flow, Proceedings of the Second International Symposium on Two-Phase Flow Modelling and Experimentation, Rome, Italy, 23–26 May (1999), pp.29–42.
8. 8) Chaouki, J., Larachi, F. and Dudukovic, M. P. (1997): Non-invasive tomographic and velocimetric monitoring of multiphase flows, Ind. & Eng. Chem. Research, 36 (11), pp.4476–4503.10.1021/ie970210t ↗
9. 9) Williams, R.A. and Xie, C.G. (1993): Tomographic techniques for characterizing particulate processes, Part. & Part. Systems Characterization, 10 (5), pp.252–261.10.1002/ppsc.19930100507 ↗
10. 10) Brown, G.J., Reilly, D. and Mills, D. (1996): Development of an ultrasonic tomography system for application in pneumatic conveying. Meas. Sci. Technol, 7, pp. 396–405.10.1088/0957-0233/7/3/022 ↗
11. 11) Rahim, R.A., Green, R.G., Horbury, N., Dickin, F.J., Naylor, B.D. and Pridmore, T.P. (1996): Further development of a tomographic imaging system using optical fibres for pneumatic conveyors. Meas. Sci. Technol, 7, pp. 419–422.10.1088/0957-0233/7/3/025 ↗
12. 12) Green, R.G., Rahim, R.A., Evans, K., Dickin, F.J., Naylor, B.D. and Pridmore, T.P. (1998): Concentration profiles in a gravity chute conveyor by optical tomography measurement. Powder Technol., 95 (1), pp.49–54.10.1016/S0032-5910(97)03315-9 ↗
13. 13) Uchiyama, H., Nakajima, M. and Yuta, S. (1985): Measurement of flame temperature distribution by IR emission computed tomography. Appl. Opt., 24, pp. 4111–4116.10.1364/AO.24.004111 ↗
14. 14) Xie, C.G., Reinecke, N., Beck, M.S., Mewes, D., Williams, R.A. (1995): Electrical tomography techniques for process engineering applications, The Chem. Eng. J., 56, pp. 127–133.10.1016/0923-0467(94)02907-5 ↗
15. 15) Yu, Z.Z., Peyton, A.T., Beck, M.S., Conway, W.F. and Xu, L.A. (1993): Imaging system based on Electromagnetic Tomography, Electronic Letters, 29, pp. 625–626.10.1049/el:19930418 ↗
16. 16) Wilkinson, A.J., Randall, E.W., Long, T.M. and Collins, A. (2006): The design of an ERT system for 3D data acquisition and a quantitative evaluation of its performance, Meas. Sci. Technol., 17, pp. 2088–2096.10.1088/0957-0233/17/8/006 ↗
17. 17) Maxwell, J.C. (1873): “A Treatise on Electricity and Magnetism vol. I”, Clarendon Press, Oxford.
18. 18) Morse, T. D. and Ballou, C. O. (1951): The uniformity of fluidisation, its measurement and use, Chem. Eng, Progress. 47, pp.199–211.
19. 19) Geldart, D. and Kelsey, J.R. (1972): The use of capacitance probes in gas fluidised beds, Powder Tech., 6, pp. 45–50.10.1016/0032-5910(72)80055-X ↗
20. 20) Abouelwafa, M.S.A. and Kendall, E.J.M (1979): Analysis and design of helical capacitance sensors for volume fraction determination, Rev. Sci. Instrum., 50 (7), pp.872–878.10.1063/1.1135942 ↗
21. 21) Dyakowski, T., Jeanmeure, L.F.C. and Jaworski, A.J. (2000): Applications of electrical tomography for gas-solids and liquid-solids flows - a review, Powder Tech., 112, pp. 174–192.10.1016/S0032-5910(00)00292-8 ↗
22. 22) Dyakowski, T., Johansen, G.A., Hjertaker, B.T., Sankowski, D., Mosorov, V. and Wlodarczyk, J. (2006): A Dual Modality Tomography System for Imaging Gas/Solids Flows, Particle & Particle Systems Characterization, 23, pp. 260–265.10.1002/ppsc.200601057 ↗
23. 23) Yang, W. (2007): Tomographic Imaging based on Capacitance Measurement and Industrial Applications, IEEE International Workshop on Imaging on Systems and Techniques, 2007, pp. 1–6.10.1109/IST.2007.379587 ↗
24. 24) Azzopardi, B.J., Abdulkareem, L.A., Zhao, D., Thiele, S., da Silva, M.J., Beyer, M. and Hunt, A. (2010): Comparison between Electrical Capacitance Tomography and Wire Mesh sensor for air/silicone oil flow in a vertical pipe, Ind. & Eng. Chem. Research, 49, pp. 8805–8811.10.1021/ie901949z ↗
25. 25) Grootveld, C. J. (1996): “Measuring & Modelling of concentrated settling suspensions using Electrical Impedance Tomography”, PhD thesis, Univ. of Delft, Delft, Holland.
26. 26) Wang, M. (2005): Impedance Mapping of Particulate Multiphase Flows, Flow Measurement and Instrumentation, 16, pp. 183–189.10.1016/j.flowmeasinst.2005.02.016 ↗
27. 27) Jia, J., Wang, M., Schlaberg, H. I. and Li, H. (2010): A Novel Tomographic Sensing System for High Electrically Conductive Multiphase Flow Measurement, Flow Measurement and Instrumentation, 21(3), pp.184–190.10.1016/j.flowmeasinst.2009.12.002 ↗
28. 28) Henderson, R.P. and Webster, J.G. (1978): An Impedance Camera for Spatially Specific Measurements of the Thorax. IEEE Transactions on Biomedical Engineering, 25 (3), pp.250–254.10.1109/TBME.1978.326329 ↗
29. 29) Barber, D.C. and Brown, B.H. (1984): Applied Potential Tomography, Journal of Physics E: Scientific Instruments, 17 (9), pp.723 – 733.10.1088/0022-3735/17/9/002 ↗
30. 30) Wang, M., Jones, T.F. and Williams, R.A. (2003): Visualization of Asymmetric Solids Distribution in Horizontal Swirling Flows Using Electrical Resistance Tomography, Chemical Engineering Research and Design 81 (8), pp.854–861.10.1205/026387603322482095 ↗
31. 31) Malmivuo, J. and Plonsey, R. (1995): “Bioelectromagnetism: Principles and Applications of Bioelectric and Biomagnetic Fields”, Oxford University Press, New York - Oxford.10.1093/acprof:oso/9780195058239.001.0001 ↗
32. 32) Pakzad, L., Ein-Mozaffari, F. and Chan, P. (2008): Using Electrical Resistance Tomography and Computational Fluid Dynamics Modelling to Study the Formation of Cavern in the Mixing of Pseudoplastic Fluids Possessing Yield Stress, Chemical Engineering Science, 63 (9), pp.2508–2522.10.1016/j.ces.2008.02.009 ↗
33. 33) Razzak, S.A., Barghi, S., Zhu, J.-X. (2009): Application of electrical resistance tomography on liquid-solid two-phase flow characterization in an LSCFB riser, Chemical Engineering Science, 64 (12), pp. 2851–2858.10.1016/j.ces.2009.02.049 ↗
34. 34) Faia, P.M., Ferreira, A.R., Santos, M.J., Santos, J.B., Silva, A.P.R., Rasteiro, M.G. and Garcia, F.A.P.: Imaging particulate two-phase flow in liquid suspensions with Electric Impedance Tomography, Particulate Science and Technology, in press.
35. 35) Karapantsios, T.D. and Papara, M. (2008): On the design of electrical conductance probes for foam drainage applications. Assessment of ring electrodes performance and bubble size effects on measurements, Colloids & Surfaces A: Physicochem. Eng. Aspects 323, pp.139–148.10.1016/j.colsurfa.2007.10.003 ↗
36. 36) Wang, M., Mann, R. and Dickin, F.J. (1999): Electrical resistance tomography sensing systems for industrial applications, Chem. Eng. Comm. 175, pp.49–70.10.1080/00986449908912139 ↗
37. 37) Lucas, G.P., Cory, J., Waterfall, R.C., Loh, W.W. and Dickin, F.J. (1999): Measurement of the solids volume fraction and velocity distributions in solids-liquids flows using dual-plane electrical resistance tomography, Flow Measurement Instrumentation 10, pp.249–258.10.1016/S0955-5986(99)00010-2 ↗
38. 38) Wang, M. and Yin, W. (2001): Measurements of concentration and velocity distribution in miscible liquid mixing using electrical resistance tomography, Trans. Chemical Engineering Research and Design, 79 (A8), pp.883–886.10.1205/02638760152721398 ↗
39. 39) Polydorides, N. and Lionheart, W.R.B. (2002): A Matlab toolkit for three-dimensional electrical impedance tomography: a contribution to the Electrical Impedance and Diffuse Optical Reconstruction Software project, Measurement Science and Technology, 13(12), pp.1871–1883.10.1088/0957-0233/13/12/310 ↗
40. 40) Kotre, C.J. (1994): EIT image reconstruction using sensitivity weighted filtered backprojection. Phys. Meas., A 15, pp.125–136.10.1088/0967-3334/15/2A/017 ↗
41. 41) Yang, W. Q., Gamio, J.C. and Beck, M.S. (1997): A fast iterative image reconstruction algorithm for capacitance tomography, Sensors and their Applications, vol. III, IOP Pub., pp.47–52.
42. 42) Lionheart, W.R.B (2001): Reconstruction algorithms for permittivity and conductivity imaging, Proceedings of the Second World Congress on Industrial Process Tomography, Hannover, Germany, 29–31 August, 2001, pp. 4–11.
43. 43) Yorkey, T.J., Webster, J.G. and Tompkins, W. (1987): Comparing reconstruction algorithms for electrical-impedance tomography, IEEE J. Bio-Med. Eng., 34, pp. 843–852.10.1109/TBME.1987.326032 ↗
44. 44) Parvareh, A., Rahimi, M., Alizadehdakhel, A. and Alsaifari, A.A. (2010): CFD and ERT investigations on two-phase flow regimes in vertical and horizontal tubes, Int. Comm. Heat & Mass Transfer, 37, pp. 304–311.10.1016/j.icheatmasstransfer.2009.11.001 ↗
45. 45) Molinari, M., Cox, S.J., Blott, B.H. and Daniell, G.J. (2001): Efficient non-linear 3D electrical tomography reconstruction, Proceedings of the Second World Congress on Industrial Process Tomography, Hannover, Germany, 29–31 August 2001, pp.424–432.
46. 46) Cho, K.H., Kim, S. and Lee, Y.J. (1999): A fast reconstruction method for the two phase flow visualization, Int. Comm. Heat & Mass Transfer, 26 (5), pp.637–646.10.1016/S0735-1933(99)00050-0 ↗
47. 47) Tapp, H.S. and Wilson, R.H. (1997): Developments in low-cost electrical imaging techniques, Process. Contr. Qual. 9, 1997, pp. 7–16.
48. 48) Sun, T.D., Mudde, R., Schouten, J.C., Scarlett, B. and Bleek, C.M. (1999): Image reconstruction of an electrical capacitance tomography system using an artificial neural network, Proceedings of the First World Congress on Industrial Process Tomography, Buxton, UK, April 1999, pp.174–180.
49. 49) Mohamad-Saleh, J., Hoyle, B.S., Podd, F.J.W. and Spink, D.M. (2001): Direct flow process estimations from tomographic data using artificial neural systems, Proceedings of the Second World Congress on Industrial Process Tomography, Hannover, Germany, 29–31 August 2001, pp.751–758.
50. 50) Hamidipour, M. and Larachi, F. (2010): Characterizing the liquid dynamics in concurrent gas-liquid flows in porous media using twin-plane electrical capacitance tomography, Chemical Engineering Journal, 165 (1):15, pp.310–323.10.1016/j.cej.2010.08.058 ↗
51. 51) Meng, S., Shi, L., Zhihong, L. and Jing, L. (2008): Application of Electrical Capacitance Tomography to the Concentration Measurement in a Cyclone Dipleg, Chinese Journal of Chemical Engineering, 16 (4), pp.635–639.10.1016/S1004-9541(08)60133-0 ↗
52. 52) Brodowicz, K., Maryniak, L. and Dyakowski, T. (1993): Application of capacitance tomography to pneumatic conveying processes, “Tomographic Techniques for Process Design and Operation”, Computational Mechanics Publications, Southampton and Boston, pp.361–368.
53. 53) Zhu, K., Rao, S. M., Wang, C. and Sundaresan, S. (2003): Electrical capacitance tomography measurements on vertical and inclined pneumatic conveying of granular solids, Chemical Engineering Science, 58 (18), pp.4225–4245.10.1016/S0009-2509(03)00306-3 ↗
54. 54) Arko, A., Waterfall, R.C., Beck, M.S., Dyakowski, T., Sutcliffe, P. and Byars, M. (1999): Development of electrical capacitance tomography for solids mass flow measurement and control of pneumatic conveying systems, in: Proceedings of the First World Congress on Industrial Process Tomography, Buxton, UK, 14–17 April 1999, pp.140–146.
55. 55) West, R.M., Wu, Y., Scott, D.M., Sunshine, G., Hoyle, B.S., Kostuch, J., McLeod, C.N. and Williams, R.A. (2001): Electrical impedance imaging of paste during extrusion, Proceedings of the Second World Congress on Industrial Process Tomography, Hannover, Germany, 29–31 August 2001, pp.300–306.
56. 56) White, R.B., and Zakhari, A. (1999): Internal structures in fluid beds of different scales: an application of electrical capacitance tomography, Proceedings of the First World Congress on Industrial Process Tomography, Buxton, UK, 14–17 April 1999, pp.39–46.
57. 57) Makkawi, Y.T. and Wright, P.C. (2001): Application of process tomography as a tool for better understanding of fluidization quality in a conventional fluidized bed, Proceedings of the Second World Congress on Industrial Process Tomography, Hannover, Germany, 29–31 August 2001, pp.324–338.
58. 58) Takei, M., Zhao, T. and Yamane, K. (2009): Measurement of particle concentration in powder coating process using capacitance computed tomography and wavelet analysis, Powder Technology, 193 (1), pp.93–100.10.1016/j.powtec.2009.02.014 ↗
59. 59) Meng, Z., Huang, Z., Wang, B., Ji, H. and Yan, Y. (2010): Air-water two-phase flow measurement using a Venturi meter and an electrical resistance tomography sensor, Flow Measurement Instrumentation, 21, pp. 268–276.10.1016/j.flowmeasinst.2010.02.006 ↗
60. 60) Bennett, M.A., West, R.M., Luke, S.P. and Williams, R.A. (2002): The investigation of bubble column and foam processes using electrical capacitance tomography, Minerals Engineering, 15 (4), pp. 225–234.10.1016/S0892-6875(02)00005-5 ↗
61. 61) Kourunen, J., Käyhkö, R., Matula, J., Käyhkö, J., Vauhkonen, M. and Heikkinen, L.M. (2008): Imaging of mixing of two miscible liquids using electrical impedance tomography and linear impedance sensor, Flow Measurement and Instrumentation 19 (6), pp.391–396.10.1016/j.flowmeasinst.2008.07.002 ↗
62. 62) Vilar, G., Williams, R.A., Wang, M. and Tweedie, R.J. (2008): On line analysis of structure of dispersions in an oscillatory baffled reactor using electrical impedance tomography, Chemical Engineering Journal, 141 (1–3), pp.58–66.10.1016/j.cej.2007.10.018 ↗
63. 63) Karhunen, K., Seppänen, A., Lehikoinen, A., Monteiro, P.J.M. and Kaipio, J.P. (2010): Electrical Resistance Tomography imaging of concrete, Cement and Concrete Research, 40 (1), pp.137–145.10.1016/j.cemconres.2009.08.023 ↗
64. 64) Boonkhao, B., Li, R. F., Wang, X. Z., Tweedie, R. J., Primrose, K. (2010): Making use of process tomography data for multivariate statistical process control, AIChE J., doi 10.1002/aic.12443,.10.1002/aic.12443 ↗
65. 65) Ricard, F., Brechtelsbauer, C., Xu, X.Y. and Lawrence, C.J. (2005): Monitoring of Multiphase Pharmaceutical Processes Using Electrical Resistance Tomography, Chemical Engineering Research and Design, 83 (7), pp.794–805.10.1205/cherd.04324 ↗
66. 66) Rimpiläinen, V., Kuosmanen, M., Ketolainen, J., Järvinen, K., Vauhkonen, M. and Heikkinen, L.M. (2010): Electrical impedance tomography for three-dimensional drug release monitoring, European Journal of Pharmaceutical Sciences, 41 (2), pp.407–413.10.1016/j.ejps.2010.07.008 ↗
67. 67) Sun, T., Tsuda, S., Zauner, K. and Morgan, H. (2010): On-chip electrical impedance tomography for imaging biological cells, Biosensors and Bioelectronics, 25 (5), pp.1109–1115.10.1016/j.bios.2009.09.036 ↗
68. 68) Ventura, C., Garcia, F.A.P., Ferreira, P. and Rasteiro, M.G. (2007): Flow Dynamics of pulp fiber suspensions, Tappi Journal, 7 (8), pp.20–26.10.32964/TJ7.8.20 ↗
69. 69) Cheng, K.S., Isaacson, D., Newell, J.C. and Gisser, D. G. (1989): Electrode Models for Electric Current Computed Tomography, IEEE Transactions on Biomedical Engineering, 36 (9), pp.918–924.10.1109/10.35300 ↗
70. 70) Schlaberg, H. I., Baas, J. H., Wang, M., Best, J. L., Williams, R. A. and Peakall, J. (2006): Electrical resistance tomography for suspended sediment measurements in open channel flows using a novel sensor design, Part. Part. Syst. Charact., 23, pp. 313–320.10.1002/ppsc.200601062 ↗
71. 71) Wang, M., Ma, Y., Holliday, N., Dai, Y., Williams, R. A. and Lucas, G. (2005): A high performance EIT system, IEEE sensors J., 5 (2), pp.289–299.10.1109/JSEN.2005.843904 ↗
72. 72) Hoyle, B. S., Jia, X., Podd, F. J. W., Schlaberg, H. I., Tan, H. S., Wang, M., West, R. M., Williams, R. A., and York, T. A. (2001): Design and application of a multimodal process tomography system, Meas. Sc. & Tech., 12, pp. 1157–1165.10.1088/0957-0233/12/8/324 ↗
73. 73) Lei, J., Liu, S., Guo, H. H., Li, Z. H., Li, J. T. and Han, Z. X. (2011): An image reconstruction algorithm based on semiparametric model for electrical capacitance tomography, Computers & Mathematics with Applications, 61, pp. 2843–2853.10.1016/j.camwa.2011.03.060 ↗
74. 74) Fan, W. R. and Wang, H. X. (2010): Maximum entropy regularization method for electrical impedance tomography combined with a normalized sensitivity map, Flow Meas. & Instr., 21, pp. 277–283.10.1016/j.flowmeasinst.2010.02.007 ↗