journal article·2013-12

Influence of mechanical behavior between the grains on stress fluctuation of aluminum alloy thick plate

Kai Liao, Yunxin Wu, Hai Gong

Publisher page

Abstract

The research on fl uctuation and inhomogeneity of internal stress of aluminum alloy thick plate is theoretical and technological base for stress control technology. By using X-ray diffraction technique and mechanical test method, aluminum alloy with typical fine sub-grains, coarse recrystallized grains, and second phase was analyzed; the interactive mechanical model between grains was built for analysis of variation of internal stress within the local micro structure by imitating the actual distribution of grains. The experimental result shows that the mechanical model can effectively explain the reason for fluctuation of microscopic stress, which also proves that the inhomogeneous distribution of metal organization is the cause for the complex distribution of microscopic stress. The model can well describe stress distribution of thick plate caused by thermal deformation. Besides, it well describes mechanism of stress fluctuation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Laser and Thermal Forming Techniques · Metallurgy and Material Forming · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. Todinov MT. Mechanism for Formation of the Residual Stress from Quenching[J].Modeling and Simulation in Materials Science and Engineering, 1998, 6(3):273–29110.1088/0965-0393/6/3/006 ↗
2. Lin GY. Fundamentsl Research Relsted to The Fabrication Technology for High Quality Thick Plates of 7X75 Series Aluminum Alloys[D]. Changsha: Central South University, 2006
3. Hu Shaoqiu, Zeng Sumin. The Theoretical Model of the Thermal Stress Evolution Mechanism during Quenching of no Phase Change Alloy —(1) The Corner and Edge Model for Thermal Stress during Quenching and the Corner Effect during Quenching[J]. Rare Metal Materials and Engineering, 2006, 35(4):538–541
4. Michael B Prime, Michael R Hill. Residual Stress, Stress Relief, and Inhomogeneity in Aluminum Plate[J]. Scripta Materialia, 2000,46(1):77–8210.1016/S1359-6462(01)01201-5 ↗
5. Gong H, Wu YX, Liao K. Infl uence of Pre-stretching on Residual Stress Distribution in 7075 Aluminum Alloy Thick-plate[J]. Transactions of Materials and Heat Treatment, 2010,30(6):201–205
6. LIAO Kai, WU Yunxin, GONG Hai. Prediction and Measurement of Quenching-prestretching Stress in Aluminum Alloy Thick Plate[J]. The Chinese Journal of Nonferrous Metals, 2010,20(10):1 901–1 906
7. Zhang XM, Han NM, Liu SD. Inhomogeneity of Texture, Tensile Property and Fracture Toughness of 7050 Aluminum Alloy Thick Plate[J]. The Chinese Journal of Nonferrous Metals, 2010,20(2):202–208
8. Deng YL, Zhang XM, Liu Y. Inhomogeneities of Icrostructures and Micro-orientations in Cold-rolled High Purity Al Columnar Grain[J]. The Chinese Journal of Nonferrous Metals, 2005,15(8):1173–1178
9. Fan XG. Study on the Microstructures and Mechanical Properties and the Fracture Behavior of the Al-Zn-Mg-Cu-Zr Alloys[D]. Harbin: Harbin Institute of Technology, 2007
10. Liu G, Zhang GJ, Ding XD. A model for Fracture Toughness of High Strength Aluminum Alloys Containing Second Particles of Various Sized Scales[J]. The Chinese Journal of Nonferrous Metals, 2002,12(4):706–713
11. Cvijovic Z, Vratnica M, Rakin M. Micromechanical Modeling of Fracture Toughness in Overaged 7000 Alloy Forgings[J]. Mater. Sci. Eng. A, 2006, 434(1/2):339–34610.1016/j.msea.2006.07.018 ↗
12. Xiong CX, Deng YL, Wan L. Evolutions of Microstructures and Textures of 7050 Al Alloy Plate during Solution Heat Treatment[J]. The Chinese Journal of Nonferrous Metals, 2010,20(3): 427–434
13. Quan GF, Cai DL, Song YJ. Analyses of Thermal and Residual Microstress in Particle and Matrix of Composites[J]. Acta Material Composite Sinica, 1995,12(3):70–75
14. Li MW, Ying ZD, Zhu JC. Analyses of Residual Thermal Microstress of ZrO2/Ni FGM[J]. Rare Metal Materials and Engineering, 2003,32(4): 254–257
15. Muammer Koc, John Culp, Taylan Altan. Prediction of Residual Stress in Quenched Aluminum Blocks and Their Reduction Through Cold Working Processes[J]. Journal of Materials Processing Technology, 2006, (17):342–354