journal article·2025-02

Bulging Performance and Quality Control of Aluminum Alloy Tailor-welded Overlapping Sheets Based on Interface Friction

Tiejun Gao, Bowen Gao, Weijie Li, Jiabin Zhang

Publisher page

Abstract

In order to solve the problem of poor formability caused by different materials and properties in the process of tailor-welded sheets forming, a forming method was proposed to change the stress state of tailor-welded sheets by covering the tailor-welded sheets with better plastic properties overlapping sheets. At the same time, the interface friction effect between the overlapping and tailor-welded sheets was utilized to control the stress magnitude and further improve the formability and quality of the tailor-welded sheets. In this work, the bulging process of the tailor-welded overlapping sheets was taken as the research object. Aluminum alloy tailor-welded overlapping sheets bulging specimens were studied by a combination of finite element analysis and experimental verification. The results show that the appropriate use of interface friction between tailor-welded and overlapping sheets can improve the formability of tailor-welded sheets and control the flow of weld seam to improve the forming quality. When increasing the interface friction coefficient on the side of tailor-welded sheets with higher strength and decreasing that on the side of tailor-welded sheets with lower strength, the deformation of the tailor-welded sheets are more uniform, the offset of the weld seam is minimal, the limit bulging height is maximal, and the forming quality is optimal.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Advanced Welding Techniques Analysis · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. Liu Z Y, Xiong B Q, Li X W, et al. Effect of Friction Coefficient on Deep Drawing of 6A16 Aluminum Alloy for Automobile Body[J]. J. Wuhan Univ. Technol.-Mat. Sci. Ed., 2023, 35(01): 208–21410.1007/s11595-020-2245-1 ↗
2. Zhao W J. The Influence of Deformation Conditions on the Deformation Behavior of AZ31 Magnesium Alloy Sheet with Different Microstructure[D]. Qinhuangdao: Yansan University, 2019
3. Peng S. Research on Mechanical Clinching Technology of AZ31 Magnesium Alloy Sheets[D]. Guangzhou: South China University of Technology, 2012
4. Chen L, Xiong A K, Wang Y J, et al. Hydroforming Technology of High Cone Parts for Aero-engine[J]. Forging & Stamping Technology, 2020, 45(07): 72–76
5. Sun C Y, Li G, Liu Y D, et al. Structural Design and Simulation Analysis on Mechanical Gripper for Welding Tailored Blank Overturning[J]. Forging & Stamping Technology, 2020, 45(05): 140–146
6. Wu J, Mao Z L, Zou F. Formability Prediction and Experimental Study on Aluminum Alloy Tailor Welded Blanks Based on Norton-Hoff Viscoplastic Theory[J]. Forging & Stamping Technology, 2022, 47(05): 109–115
7. Bandyopadhyay K, Panda S K, Saha P, et al. Limiting Drawing Ratio and Deep Drawing Behavior of Dual Phase Steel Tailor Welded Blanks: FE Simulation and Experimental Validation[J]. J. Mater. Process. Tech., 2015, 217: 48–6410.1016/j.jmatprotec.2014.10.022 ↗
8. Zhan M, Xing L, Gao P F, et al. Advances in Plastic Forming of Lightweight Components with Tailor Welded Plate[J]. Journal of Netshape Forming Engineering, 2019, 11(05): 1–12
9. Wang Z J, Song H, Wang Z. Deformation Behavior of TC1 Titanium Alloy Sheet under Double-sided Pressure[J]. T. Nonferr. Metal. Soc., 2008, 18(01): 72–7610.1016/S1003-6326(08)60013-8 ↗
10. Zhang Z C, Xu Y C, Yuan S J. Effect of Outer Stainless Steel on the Deformation Behavior of Hydro-bulging of 5A06 Aluminum Alloy Sheet[J]. Journal of Mechanical Engineering, 2016, 52(14): 40–4710.3901/JME.2016.14.040 ↗
11. Zhu F C. Research on Influencing Factors and Control Methods of Forming Quality of Tailor-welded Blanks[D]. Harbin: Harbin Institute of Technology, 2020
12. Guan Y P, Ma X D, Zhang D Q. Variable Blank Holder Force Curve Prediction in Deep Drawing for Square Box of Tailor-welded Blanks[J]. Journal of Plasticity Engineering, 2017, 24(02): 17–21
13. Gao T J, Yao Y J, Wang X K, et al. Effect of Interface Friction on Overlapping Sheets Bulging Formability and Microstructure of 5A02 Aluminum Alloy[J]. J. Wuhan Univ. Technol. -Mat. Sci. Ed., 2019, 34(04): 919–92410.1007/s11595-019-2138-3 ↗
14. Yu L H, Chen S P. Numerical Simulation Research on Formability of Tailor-welded Blanks Based on Dynaform[J]. Forging & Stamping Technology, 2011, 36(04): 68–72