Fatigue Strength Analysis of Dissimilar Aluminum Alloy TIG Welds
Source abstract
Abstract
The constant amplitude loading fatigue tests were carried out on the 6061/7075 aluminum alloy TIG fillet welded lap specimens in this study, and the weld seam cross-section hardness was measured. The experimental results show that most specimens mainly failed at the 7075 side weld toes even though the base material tensile strength of 7075 is higher than that of 6061. The maximum stress-strain concentration in the two finite element models is located at the 7075 side weld toe, which is basically consistent with the actual fracture location. The weld zone on the 7075 side experiences severe material softening, with a large gradient. However, the Vickers hardness value on the 6061 side negligibly changes and fluctuates around 70 HV. No obvious defects are found on the fatigue fracture, but a large number of secondary cracks appear. Cracks germinate from the weld toe and propagate in the direction of the plate thickness. Weld reinforcement has a serious impact on fatigue life. Fatigue life will decrease exponentially as the weld reinforcement increases under low stress. It is found that the notch stress method can give a better fatigue life prediction for TIG weldments, and the errors of the predicted results are within the range of two factors, while the prediction accuracy decreases under low stress. The equivalent structural stress method can also be used for fatigue life prediction of TIG weldments, but the errors of prediction results are within the range of three factors, and the accuracy decreases under high stress.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fatigue and fracture mechanics · Advanced Welding Techniques Analysis · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Wang J T, Chen J W, Zhang Y K, et al. Influence of Ultrasonic Impact Treatment on Stress Corrosion of 7075 Aluminum Alloy and Its Welded Joints[J]. Eng. Fail. Anal., 2023, 144: 106 90810.1016/j.engfailanal.2022.106908 ↗
2. Niu P L, Li W Y, Yang C G, et al. Low Cycle Fatigue Properties of Friction Stir Welded Dissimilar 2024-to-7075 Aluminum Alloy Joints[J]. Mater. Sci. Eng.: A, 2022, 832: 142 42310.1016/j.msea.2021.142423 ↗
3. Deng A L, Chen H, Zhang Y B, et al. Prediction of the Influence of Welding Metal Composition on Solidification Cracking of Laser Welded Aluminum Alloy[J]. Mater. Today Commun., 2023, 35: 105 55610.1016/j.mtcomm.2023.105556 ↗
4. Wang Y J, Chen M A, Wu C S. HF Pulse Effect on Microstructure and Properties of AC TIG Butt-welded Joint of 6061Al Alloy[J]. J. Manuf. Process, 2020, 56(part A): 878–88610.1016/j.jmapro.2020.05.055 ↗
5. Kumar P, Arif A, Prasad A C V S, et al. Study of Welding Process Parameter in TIG Joining of Aluminum Aolly (6061)[J]. Mater. Today: Proc., 2021, 47(13): 4 020–4 025
6. Dwivedi U, Tiwari S, Mishra A, et al. Comparative Study of Weld Characteristics of Friction Stir Welded Joints on Aluminium 7075 with Autogenous TIG[J]. Mater. Today: Proc., 2020, 22(Part 4): 2 532–2 538
7. Zhu Q Y, Lu P M, Xiang Q Y. Fatigue Life Evaluation of Web Butt Welding Structure on Boom of Excavator by Hot Spot Stress Approach[J]. Eng. Fail. Anal., 2020, 113(2): 104 54710.1016/j.engfailanal.2020.104547 ↗
8. Ren D Q, Jiang Y, Hu X A, et al. Investigation of Tensile and High Cycle Fatigue Failure Behavior on a TIG Welded Titanium Alloy[J]. Intermetallics, 2021, 132: 107 11510.1016/j.intermet.2021.107115 ↗
9. Wan Z D, Meng D Y, Zhao Y, et al. Improvement on the Tensile Properties of 2219-T8 Aluminum Alloy TIG Welding Joint with Weld Geometry Optimization[J]. J. Manuf. Process, 2021, 67: 275–28510.1016/j.jmapro.2021.04.062 ↗
10. Zhao H, Li M J, Wang X D, et al. Intergranular Corrosion Effect on Fatigue Behavior of Dissimilar 6005A-5083 Aluminum Alloys Weld Joints[J]. Mater. Corros., 2022, 73(9): 1 505–1 51810.1002/maco.202213122 ↗
11. Chen Y J, Xu P D, Liu C C, et al. Multiaxial Fatigue Behavior and Life Prediction of 7075-T651 Aluminum Alloy under Two-step Loading[J]. Eng. Fract. Mech., 2020, 230: 107 00710.1016/j.engfracmech.2020.107007 ↗
12. Rotella G. Effect of Surface Integrity Induced by Machining on High Cycle Fatigue Life of 7075-T6 Aluminum Alloy[J]. J. Manuf. Process, 2019, 41: 83–9110.1016/j.jmapro.2019.03.031 ↗
13. Zhao X Y, Xie S Q, Zhang Y L, et al. Fatigue Reliability Analysis of Metro Bogie Frame Based on Effective Notch Stress Method[J]. Eng. Fail. Anal., 2022, 131: 105 81110.1016/j.engfailanal.2021.105811 ↗
14. Wang Q D, Wang L B, Ji B H, et al. Modified Effective Notch Stress Method for Fatigue Evaluation of Rib-deck Welds Integrating the Critical Distance Approach[J]. J. Constr. Steel Res., 2022, 196: 107 37310.1016/j.jcsr.2022.107373 ↗
15. Wang R J, Mi P. Study on Fatigue Strength of FSW Joints of 5083 Aluminum Alloy with Kissing Bond Defect[J]. J. Mech. Sci. Technol., 2020, 34(7): 2 761–2 76610.1007/s12206-020-0608-3 ↗
16. Sonsino C M. A Consideration of Allowable Equivalent Stresses for Fatigue Design of Welded Joints According to the Notch Stress Concept with the Reference Radii rref = 1.00 and 0.05 mm[J]. Weld World, 2009, 53(3–4): R64–R7510.1007/BF03266705 ↗
17. Zhang L Y, Dong P S, Wang Y D, et al. A Coarse-mesh Hybrid Structural Stress Method for Fatigue Evaluation of Spot-Welded Structures[J]. Int. J. Fatigue, 2022, 164: 107 10910.1016/j.ijfatigue.2022.107109 ↗
18. Liu Y, Deng C Y, Gong B M, et al. Fatigue Limit Prediction of Notched Plates using the Zero-point Effective Notch Stress Method[J]. Int. J. Fatigue, 2021, 151: 106 39210.1016/j.ijfatigue.2021.106392 ↗
19. Dong P S, Hong J K, Osage D A, et al. Master S-N Curve Method for Fatigue Evaluation of Welded Components[J]. Weld. Res. Counc. Bull., 2002, (474): 1–50
20. Li J, Zhang Q H, Bao Y, et al. An Equivalent Structural Stress-based Fatigue Evaluation Framework for Rib-to-deck Welded Joints in Orthotropic Steel Deck[J]. Eng. Struct., 2019, 196: 109 30410.1016/j.engstruct.2019.109304 ↗
21. Yürük A, Çevik B, Kahraman N. Analysis of Mechanical and Microstructural Properties of Gas Metal Arc Welded Dissimilar Aluminum Alloys (AA5754/AA6013)[J]. Mater. Chem. Phys., 2021, 273(2–3): 125 11710.1016/j.matchemphys.2021.125117 ↗
22. Hima Bindu A, Chaitanya B S K, Ajay K, et al. Investigation on Feasibility of Dissimilar Welding of AA2124 and AA7075 Aluminium Alloy Using Tungsten Inert Gas Welding[J]. Mater. Today: Proc., 2020, 26(Part 2): 2 283–2 288
23. Mehdi H, Mishra R S. Effect of Friction Stir Processing on Mechanical Properties and Heat Transfer of TIG Welded Joint of AA6061 and AA7075[J]. Def. Technol., 2021, 17(3): 715–72710.1016/j.dt.2020.04.014 ↗